Metra Electronics 99-7631B User manual

REV. 1/25/2017 INST99-7631B
INSTALLATION INSTRUCTIONS FOR PART 99-7631B
METRA – The World’s best kits.®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
CAUTION! All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
• ISO DIN radio provision with pocket
• Painted matte black
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (8) #8 x 3/8” Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7552 Antenna Adapter: • 40-NI12
• Panel removal tool • Phillips screwdriver
• 12mm socket wrench • T-20 Torx driver
TOOLS REQUIRED
Nissan Titan 2017-up, Titan XD 2016-up
99-7631B
Table of Contents
A B C D
Dash Disassembly ..............................................2-5
Kit Assembly .......................................................... 6

99-7631B
2
Dash Disassembly
1. Remove the (2) Phillips screws
securing the knee bolster panel
below the steering column, and
then unclip the panel. It is not
necessary to completely remove
the panel. (Figure A)
2. Unclip and remove the passenger
door sill and kick panel. (Figure B)
3. Remove the (5) T-20 Torx screws
securing the glove box and then
remove. There are (2) screws
below the glove box, and (3)
screws exposed when you open
the glove box. (Figures C and D)
Continued on next page
(Figure B)
(Figure D)
(Figure A) (Figure C)
Upper screws
Lower screws

99-7631B
3
Dash Disassembly
4. Unclip and remove the (2) side
trim panels at the front of the
center console, and then remove
the (1) Phillips screw exposed
behind each panel. Tip: Pull out on
the front sides of the console to
release for later steps. (Figure E)
5. Slide both of the front seats
forward and then remove the (2)
12mm bolts from the rear sides of
the center console. Slide the seat
back once done. (Figure F)
6. Unclip and remove either the front
console pocket or heated seat
controls, depending on options
available. (Figure G)
Continued on next page
(Figure F)(Figure E) (Figure G)

99-7631B
4
Dash Disassembly
7. Unclip and remove the trim panel
where the center console and the
dashboard meet, and then remove
the (2) Phillips screws exposed.
(Figure H)
8. Slide the center console back, and
then unclip and remove the vent
panels from each side of the radio/
climate control panel. (Figure I)
9. Remove the (2) Phillips screws
securing the accessory panel
below the climate control panel,
and then unclip and remove.
(Figure J)
Continued on next page
(Figure J)(Figure I)(Figure H)

99-7631B
5
10. Remove the (2) Phillips screws
securing the climate control panel
and then remove. (Figure K)
11. Remove the (4) Phillips screws
securing the radio and then
remove. (Figure L)
12. Slightly loosen the (8) T-20
Torx screws securing the radio
brackets. Remove the (2) T-20
Torx screws securing the “white”
climate control module below
the radio and then remove. This
module will be reused in kit
assembly. (Figure M)
Continue to kit assembly
Dash Disassembly
(Figure M)
(Figure L)
(Figure K)

99-7631B
6
Kit Assembly
1. Attach the radio brackets to the
radio trim panel using the
(4) #8 x 3/8” Phillips screws
provided. (Figure A)
2. Slide the “white” climate
control module removed in dash
disassembly into the lower portion
of the bracket/panel assembly,
and then secure with the factory
hardware. (Figure B)
3. Secure the pocket to the bracket/
panel assembly using the
(4) #8 x 3/8” Phillips screws
provided. (Figure C)
4. Remove the metal DIN sleeve and
trim ring from the aftermarket radio.
5. Slide the radio into the completed
assembly, and then secure it to the
assembly using the screws supplied
with the radio. (Figure D)
6. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Test the radio for proper
operation.
7. Reassemble the dash in reverse
order of disassembly.
(Figure C)
(Figure B) (Figure D)
(Figure A)

99-7631B
7

REV. 1/25/2017 INST99-7631B
INSTALLATION INSTRUCTIONS FOR PART 99-7631B
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
IMPORTANT
If you are having difficulties with the installation
of this product, please call our Tech Support line
at 1-800-253-TECH. Before doing so, look over
the instructions a second time, and make sure
the installation was performed exactly as the
instructions are stated. Please have the vehicle
apart and ready to perform troubleshooting
steps before calling.
METRA – The World’s best kits.®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION

INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7631B
METRA. The World’s best kits.®metraonline.com1-800-221-0932 © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
REV. 1/25/2017 INST99-7631B
¡PRECAUCIÓN! Todos los accesorios, interruptores,
paneles de control climático y especialmente las luces
indicadoras de bolsa de aire deben estar conectados
antes de encender el encendido. Además, no extraiga la
radio de fábrica con la llave en la posición de encendido,
o mientras el vehículo esté funcionando.
Indice
• Herramienta para quitar paneles
• Destornillador Phillips • Llave del tubo 12mm
• Destornillador T-20 Torx
HERRAMIENTAS REQUERIDAS
Desmontaje del tablero................................................2
Ensamble del kit .................................................... 3
• Provisión de radio ISO DIN con cavidad
• Pintura negra mate
• A) Panel de la moldura del radio • B) Soportes del radio
• C) Cavidad • D) (8) Tornillos Phillips #8 x 3/8”
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)
Arnés de cables: • 70-7552 Adaptador de antena: • 40-NI12
Nissan Titan 2017 y mas, Titan XD 2016 y mas
99-7631B
A B C D

99-7631B
Desmontaje del tablero
2
1. Quite los (2) tornillos Phillips que
sujetan el panel del protector de
rodillas debajo de la columna de
dirección, luego desenganche el
panel. No es necesario quitar el
panel por completo. (Figura A)
2. Desenganche y quite el apoyo de
la puerta y el panel de protección.
(Figura B)
3. Quite los (5) tornillos T-20 Torx
que sujetan la caja de la guantera
y luego quítela. Hay (2) tornillos
debajo de la caja de la guantera y
(3) tornillos expuestos cuando abre
la caja de la guantera.
(Figura C, D)
Continúa en la siguiente página
(Figura B)
(Figura D)
(Figura A) (Figura C)
Tornillos superiores
Tornillos inferiores