Metra Electronics LEXUS 99-8151 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-8151
Phillips Screwdriver • Small Flat Blade Screwdriver or Panel Removal Tool • Cutting Tool
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
•DIN Radio Provision With Pocket
•ISO Radio Provision With Pocket
• Two ISO Units Provision
•Double DIN Radio Provision
(A) Radio Housing • (B) Pocket Trim Plate
KIT COMPONENTS
TOOLS REQUIRED:
ABCD
APPLICATIONS
Lexus IS 300 2001-2005
(C) Double DIN Trim Plate • (D) ISO Trim Plate
(E) Pocket • (F) Rear Support Bracket
(G) Mounting Brackets • (H) Double DIN Spacer Brackets • (I) ISO Snap-in Brackets
EF
HIJK
( J ) (6) #8X3/8” Phillips Truss Head Screws • (K) (2) #8X3/8” Phillips Pan Head Screws
99-8151
G

Dash Disassembly
Lexus IS 300 2001-2005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1, 2
Kit Assembly
DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 3, 4
ISO Radio Provision with Pocket .......................5, 6
Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 8
Two ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9, 10
Final Assembly ......................................11
TABLE OF CONTENTS
99-8151

99-8151
1
NOTE: Disconnect the negative
battery terminal to prevent an
accidental short circuit.
1
Using a small flat blade screwdriver,
unsnap and remove the liner from
the tray above the center vents.
(Figure A)
2
LEXUS IS 300 2001-2005
Remove (2) Phillips screws from
inside the tray.
(Figure B)
3
Using a small flat blade screw driver,
unsnap and remove the center trim
panel including vents and tray.
(Figure C)
4
DASH DISASSEMBLY
A
B
C

2
99-8151
DASH DISASSEMBLY
Remove (4) Phillips screws securing
climate controls to the factory brack-
ets and remove the climate controls.
7
Remove (4) 10mm bolts securing
radio/climate control assembly,
unplug and remove assembly.
(Figure E)
6
E
LEXUS IS 300 2001-2005
SNOW SNOW
TRAC
TRAC
OFF
OFF
D
Using a small flat blade screwdriver,
unsnap and remove switch panel
below radio.
(Figure D)
5

99-8151
KIT ASSEMBLY
Position the pocket trim-plate in the
bottom of the radio housing.
(Figure A)
1
Secure the mounting brackets to
radio housing/pocket assembly using
(2) #8 x 3/8” Phillips truss head
screws and (2) #8 x 3/8” Phillips pan
head screws provided with the kit.
(Figure C)
3
DIN RADIO PROVISION WITH POCKET
A
C
3
B
Attach the pocket to the pocket trim-
plate using (2) #8 x 3/8” Phillips
truss head screws provided with the
kit.
(Figure B)
2
LEXUS IS 300 2001-2005

99-8151
KIT ASSEMBLY
DIN RADIO PROVISION WITH POCKET
LEXUS IS 300 2001-2005
D
F
4
E
Mount the rear support bracket to
the back of the pocket using (2) #8 x
3/8” Phillips truss head screws pro-
vided with the kit. (Figure D)
4
Slide the DIN cage into the radio
housing/pocket assembly and secure
by bending locking tabs outward.
(Figure E)
6
Slide the DIN radio into the DIN cage
until it snaps into place.
(Figure F)
7
Continue to final assembly.
8
Align and engage the (3) tabs on the
bottom of the climate controls to the
top edge of the radio housing/pocket
assembly. Secure the climate con-
trols to the assembly using the (4)
factory Phillips screws previously
removed from the climate controls.
5

5
Position the pocket trim-plate in the
bottom of the radio housing.
(Figure A)
1
Attach the pocket to the pocket trim-
plate using (2) #8 x 3/8” Phillips
truss head screws provided with the
kit.
(Figure B)
2
Secure the mounting brackets to
radio housing/pocket assembly
using (2) #8 x 3/8” Phillips truss
head screws and (2) #8 x 3/8”
Phillips pan head screws provided
with the kit.
(Figure C)
3
Mount the rear support bracket to
the back of the pocket using (2) #8 x
3/8” Phillips truss head screws pro-
vided with the kit.
(Figure D)
4
ISO RADIO PROVISION WITH POCKET
99-8151
KIT ASSEMBLY
A
B
C
D
LEXUS IS 300 2001-2005

6
Align and engage the (3) tabs on the
bottom of the climate controls to the
top edge of the radio housing/pocket
assembly. Secure the climate con-
trols to the assembly using the (4)
factoryPhillips screws previously
removed from the climate controls.
5
Mount the ISO Brackets to the radio
with the screws supplied with the
radio.
(Figure E)
6
Slide the radio into the radio housing
assembly until it snaps into place.
(FigureF)
7
Snap the ISO Trim-plate onto the
Radio Housing.
(Figure G)
8
Continue with final assembly.
9
Note: To remove the radio from the
housing unclip and remove the ISO
trim-plate. Using a small blade
screw driver release the clips on the
ISO snap in brackets and slide the
radio out of the housing assembly.
ISO RADIO PROVISION WITH POCKET
99-8151
KIT ASSEMBLY
E
F
G
LEXUS IS 300 2001-2005

7
Insert the double din spacer brackets
into the mounting brackets.
(Figure A)
1
Secure the mounting brackets/spac-
ers to radio housing using (2) #8 x
3/8” Phillips truss head screws and
(2) #8 x 3/8” Phillips pan head
screws provided with the kit.
(Figure B)
2
DOUBLE DIN RADIO PROVISION
Align the holes in the brackets/spac-
ers with the holes in the aftermarket
double DIN radio and mount the
brackets/spacers to the radio using
the screws supplied with the radio.
(Figure C)
3
99-8151
KIT ASSEMBLY
A
B
C

8
Cut and remove the center divider
from the double DIN trim-plate.
(Figure D)
5
Snap the double DIN trim-plate onto
the radio housing.
(Figure E)
6
DOUBLE DIN RADIO PROVISION
Continue with final assembly.
7
99-8151
KIT ASSEMBLY
E
D
Align and engage the (3) tabs on the
bottom of the climate controls to the
top edge of the radio housing
assembly. Secure the climate con-
trols to the assembly using the (4)
factory Phillips screws previously
removed from the climate controls.
4