Metra Electronics 99-8220 User manual

INSTALLATION INSTR CTIONS FOR PART 99-8220
99-8220
APPLICATIONS
Toyota
Tundra 2007-2011
Sequoia 2008-2011
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• 99-8220 - Scratch Resistant Matte Black
• 99-8220HG - High Gloss Black
• 99-8220CHG - High Gloss Charcoal (matches 2010-UP models)
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
KIT COMPONENTS
A
TOOLS RE UIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932
© COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
D
E
C
F
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wire harness:
• 70-1761 Toyota 87-up
• TYTO-01 Toyota amp interface harness 03-up
Antenna adapter:
• Not requi red

D sh Dis ssembly
- Toyot Tundr (Console Shift ) 2007-2011 . . . . . . . . . . . . 1,2
- Toyot Sequoi 2008-2011 . . . . . . . . . . . . . . . . . . . . . . . . 1,2
- Toyot Tundr (Column Shift ) 2007 -2011 . . . . . . . . . . . . . 3
- Toyot Sequoi 2008-2011 . . . . . . . . . . . . . . . . . . . . . . . . 3
Kit Assembly
- DIN R dio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
- ISO Mount R dio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . .5
- Double DIN R dio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
- St cked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . ..7
Fin l Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
TABLE OF CONTENTS
99-8220
*Note:
Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.

99-8220 DASH DISASSEMBLY
TOYOTA T NDRA (Console Shift) 2007-2011
TOYOTA SEQ OIA 2008-2011
1
1
Remove (1) Phillips screw from shifter
trim panel and remove panel.
( Figure B)
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
3
Unclip and remove the top trim panel
around cup holders. (
Figure A)
2
Unclip, unplug and remove the cli-
mate control assembly. ( Figure C)
4
Continue dash disassembly.
A
B
C

99-8220 DASH DISASSEMBLY
D
E
6
Remove (4) 10 MM bolts securing the
radio. ( Figure D)
Unclip the right side of the instrument
panel trim and pull back the trim,then
unclip,unplug and remove radio.
(
Figure E)
5
Continue to kit assembly.
2
TOYOTA T NDRA (Console Shift) 2007-2011
TOYOTA SEQ OIA 2008-2011

99-8220 DASH DISASSEMBLY
TOYOTA T NDRA (Column Shift) 2007-2011
3
1
Pull the cup holder out and depress
the (2) clips on each side to slide cup
holder out of cup holder panel.
(
Figure B)
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
3
Remove (2) plastic Phillips screws
one from each side of the trim panel
below the cup holder then unclip and
remove the panel. (
Figure A)
2
Remove (4) Phillips screws from cup
holder panel assembly then unclip
and remove assembly. (
Figure C)
4
Unclip and remove the climate control
assembly. (
Figure D)
5
Remove (4) 10 MM bolts securing the
radio.
6
Unclip the right side of the instrument
panel trim and pull back then unclip
and remove radio.
7
Continue to kit assembly.
A
B
C
D
TOYOTA SEQ OIA 2008-2011

99-8220 KIT ASSEMBLY
4
A
B
C
DIN MO NT RADIO PROVISION WITH POCKET
Slide the DIN cage into the radio hous-
ing and secure by bending the metal
locking tabs outward.
(Figure A)
1
Slide the aftermarket radio into the cage
until it snaps into place.
(Figure B)
2
Snap the pocket into the radio housing.
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-8220 KIT ASSEMBLY
5
A
B
C
D
ISO MO NT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radio
using the screws supplied with the
radio.
(Figure A)
1
Slide the radio into the radio housing
until it snaps into place. (Figure B)
2
Snap the trim plate onto the front of
the Radio/Housing assembly. (Figure C)
3
Snap the Pocket into the radio
housing.
(Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-8220 KIT ASSEMBLY
6
DO BLE DIN RADIO PROVISION
Cut and remove the center bar from
the radio housing.
(Figure A)
1
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Slide the Double DIN radio into the
bracket/radio housing assembly and
secure the radio to the assembly using
the screws supplied with the radio.
(Figure C)
3
Snap the Double DIN trim plate onto
the front of the radio/housing assem-
bly. (Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C

99-8220 KIT ASSEMBLY
7
STACKED ISO MO NT NITS PROVISION
Cut and remove the center bar from
the radio housing.
(Figure A)
1
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Slide the stacked ISO mount units into
the bracket/housing assembly and
secure the units to the assembly using
the screws supplied with the units.
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
Snap the Double DIN trim plate onto
the front of the radio/housing assem-
bly. (Figure C)
4

99-8220 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends b ck 1/2"
B) Twist ends together
C) Solder
D) T pe
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring onne tions using the EIA olor ode hart shown below and the instru tions in luded with the
head unit. Metra re ommends making onne tions as shown below; Strip, Spli e, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent ele tri al short ir uit.
METRA / EIA WIRING CODE
12V Ignition / A . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Bla k*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Bla k / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Bla k
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Bla k
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Bla k
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Bla k
*NOTE: When a Bla k wire is not present, ground radio to vehi le hassis.
All olors may not be present on all leads due to manufa turer’s spe ifi ations.
8