Metra Electronics 98-9306 User manual

APPLICATIONS
KIT FEATURES
KIT COMPONENTS
TOOLS REQUIRED
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932 metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
INSTALLATION INSTRUCTIONS FOR PART 98-9306
BMW
3 SERIES 2006-2010
(Not for models with Factory Navigation)
98-9306
Relocates Heated Seat Switches•
(Used For Heated Seat Models When
Using The 95-9306B)
• A) Pocket • B) Heated Seat Switch Trim Panel • C) Extension Harness
• Phillips Screwdriver • Panel Removal Tool • Small Flat Blade Screwdriver
• Torx Screwdriver
ABC

TABLE OF CONTENTS
DASH DISASSEMBLY
•BMW 3 Series 2006-10 . . . . . . . . . . . . . . . . . . . 1-2
KIT ASSEMBLY
•BMW 3 Series 2006-10 . . . . . . . . . . . . . . . . . . . 3-4
*NOTE: Refer also to the instructions included with the aftermarket radio.
CAUTION: Metra recommends disconnecting the negative battery terminal
before beginning any installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before reconnecting the battery
or cycling the ignition.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP certified
technicians
INSTALLATION INSTRUCTIONS FOR PART 98-9306

BMW 3 SERIES 2006-2010
98-9306 DASH DISASSEMBLY
Carefully unclip and remove the
shifter trim panel. (Fig. A)
Remove (4) Torx screws securing
the pocket or ash tray assembly to
the shifter trim panel. (Fig. B)
Unclip and remove the heated seat
switch assembly from the climate
control panel.
Remove (5) Torx screws securing
the back cover on the heated seat
switch assembly. (Fig. C)
1
2
3
4
A
B
C
1
Continue to PG.2...........................

2
5
D
Continue to Kit Assembly..............
98-9306 DASH DISASSEMBLY
Remove the circuit board and unplug the factory harness. (Fig. D)
BMW 3 SERIES 2006-2010

3
98-9306 KIT ASSEMBLY
BMW 3 SERIES 2006-2010
Plug the extension harness onto the circuit board. Then reassemble the
heated seat switch assembly. (Fig. A)
1
A
Continue to PG.4...........................

4
98-9306 KIT ASSEMBLY
BMW 3 SERIES 2006-2010
2
3
4
5
B
Clip the heated seat switch trim panel into the pocket. (Fig. B)
Clip the heated seat switch assembly into the pocket/trim panel assembly. (Fig. B)
Reattach the 98-9306 pocket assembly to the shifter trim panel using the
factory hardware.
Route the extension harness through the left side of the dash cavity and plug
it into the climate control.

APLICACIONES
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
HERRAMIENTAS REQUERIDAS
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932 metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
INSTRUCCIONES PARA LA INSTALACIÓN DE PARTE 98-9306
BMW
SERIE 3 2006-2010
(No apto para modelos con navegación de fábrica)
98-9306
• Reubica interruptores del asiento con
calefacción
(Empleado para los modelos de asiento con
calefacción cuando se utiliza el 95-9306B)
• A) Bolsillo • B) Panel de terminación con interruptor para el asiento con calefacción
• C) Extension Harness
• Destornillador Phillips • Destornillador Torx • Herramienta para retirar paneles
• Destornillador de hoja plana pequeño
ABC

PÁGINA DE ÍNDICE
DESMONTAJE DEL TABLERO
•BMW Serie 3 2006-2010 . . . . . . . . . . . . . . . . . 1-2
MONTAJE DEL KIT
•BMW Serie 3 2006-2010 . . . . . . . . . . . . . . . . . 3-4
* NOTA: Consulte también las instrucciones incluidas con la radio del mer-
cado de accesorios.
Precaución: Metra recomienda desconectar el terminal negativo de la
batería antes de comenzar cualquier instalación. Todos los accesorios,
interruptores y, especialmente, las luces indicadoras de airbag deben estar
enchufados antes de volver a conectar la batería o comenzar el ciclo de
ignición.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP certified
technicians
INSTRUCCIONES PARA LA INSTALACIÓN DE PARTE 98-9306

BMW SERIE 3 2006-2010
98-9306 DESMONTAJE DEL TABLERO
Desenganche y retire con cuidado el
panel de terminación de la palanca
de velocidades. (FIg. A)
Retire (4) tornillos Torx que sujetan
el conjunto del bolsillo o del cenicero
en el panel de terminación de la
palanca de velocidades. (FIg. B)
Desenganche y retire el conjunto
del interruptor del asiento con
calefacción del panel de control de
clima.
Retire (5) tornillos Torx que sujetan
la cubierta posterior sobre el
conjunto del interruptor del asiento
con calefacción. (FIg. C)
1
2
3
4
A
B
C
1
Continuar con la PG.2 .........................

2
5
D
Continuar con la Asamblea Kit......
Retire el tablero de circuitos y desenchufe el arnés de fábrica. (Fig. D)
98-9306 DESMONTAJE DEL TABLERO
BMW SERIE 3 2006-2010