Metra Electronics 99-5819 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-5819
99-5819
KIT FEATURES
•DIN Radio Provision With Pocket
•ISO Mount Radio Provision With Pocket
•A) Radio Housing •B) Radio Housing Brackets • C) ISO Brackets • D) Trim Plate
KIT COMPONENTS
1-800-221-0932
©COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
A
APPLICATIONS
FORD
F-150 (XL Models Only) 2009-10
Cutting Tool • Phillips Screwdriver • Socket Wrench
B
C
D
TOOLS REQUIRED:
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wireharness:
•70-5520 Ford harness 2003-up
Antenna adapter:
•40-CR10 Chrysler antenna 2002-up

Dash Disassembly
- FORD F-150 (XL Models Only) 2009-10 . . . . . . . . . . . . . . . . . .1
Kit Assembly
-DIN Radio Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
-ISO Mount Radio Provision With Pocket. . . . . . . . . . . . . . . . . . . . . . . . 3
Final Assembly . . .........................................4
TABLE OF CONTENTS
99-5819
*Note:
Refer also to the instructions included with the aftermarket radio.

99-5819 DASH DISASSEMBLY
FORD F-150 ( XL Models Only ) 2009-10
A
B
C
D
1
1
Remove the rubber pad at the top of
the radio trim panel then remove the
(2) 9/32” screws exposed. ( Figure B)
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
3
Unclip and remove the switch panel
to the right of the cigarette lighter
then remove the (1) 9/32” screw
exposed. (
Figure A)
2
Unclip and pull the side panels con-
taining the a/c vents away from the
radio trim panel. Note: It is not nec-
essary to remove the panels com-
pletely. ( Figure C)
4
Unclip and remove the radio trim
panel. (
Figure D)
5
Remove (4) 9/32” screws to remove
the factory radio.
6
Continue to kit assembly.

99-5819 KIT ASSEMBLY
2
DIN RADIO PROVISION WITH POCKET
Cut and remove the top (2) mounting
holes off of the radio housing.
Note: The notch in the housing
should be on top. (Figure A)
1
Slide the included brackets onto the
sides of the radio housings pocket
from the back of the housing
forward.
(Figure B)
2
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down.
(Figure C)
3
Slide the aftermarket head unit into
the cage and secure. (Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
CUT HERE -TOP LEG ONLY
CUT HERE -TOP LEG ONLY
CUT
CUT
A
B
C
D

99-5819 KIT ASSEMBLY
3
ISO MOUNT RADIO PROVISION WITH POCKET
Cut and remove the top (2) mounting
holes off of the radio housing.
Note: The notch in the housing
should be on top. (Figure A)
1
Slide the included brackets onto the
sides of the radio housings pocket
from the backof the housing
forward.
(Figure B)
2
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit.
(Figure C)
3
Slide the head unit into the radio
opening until the side clips engage.
(Figure D)
4
Snap the trim plate into the Radio
Housing. (Figure D)
5
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
CUT HERE -TOP LEG ONLY
CUT HERE -TOP LEG ONLY
CUT
CUT
A
B
C
D