Metra Electronics 95-7323 User manual

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
APPLICATIONS
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 95-7323
WIRING & ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-1004 Hyundai/Kia harness 2004-up
Antenna Adapter:
• Not Required
Hyundai Entourage 2007-2008
Kia Sedona 2006-up
95-7323
• Double DIN radio provision
• Stacked ISO units provision
Panel Removal Tool • Phillips Screwdriver • Small Flat Blade Screwdriver
A B
A) • Double DIN Trim Plate B) • Double DIN Brackets
TOOLS REQUIRED
KIT FEATURES
KIT COMPONENTS

Table of Contents
Dash Disassembly
– Hyundai Entourage 2007-2008
– Kia Sedona 2006-up 3
Kit Assembly
– Double DIN radio provision 4
– Stacked ISO units head provision 5
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
95-7323
Caution
Metra recommends disconnecting the negative battery terminal before beginning any
installation. All accessories, switches, and especially air bag indicator lights must be
plugged in before reconnecting the battery or cycling the ignition.
*NOTE: Refer also to the instructions included with the aftermarket radio.

1. Unclip and remove panel surrounding
shifter. (Figure A)
2. Remove (2) Phillips screws at bottom
corners of panel surrounding radio.
(Figure B)
3. Unclip and remove entire panel
surrounding radio including the clock
and a/c vents. (Figure C)
4. Remove (4) Phillips screws
securing radio.
5. Unplug and remove the radio.
Continue to kit assembly
3
Dash Disassembly
95-7323
(Figure A)
(Figure B)
(Figure C)

4
Kit Assembly 95-7323
Double DIN radio provision
1. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2. Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate. (Figure A)
3. Slide the Double DIN radio into the
bracket/trim plate assembly and secure
the radio to the assembly using the
screws supplied with the radio.
(Figure B)
4. Reassemble dash in reverse order
of disassembly.
(Figure A)
(Figure B)

5
Kit Assembly 95-7323
1. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2. Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate. (Figure A)
3. Slide the stacked ISO units into the
bracket/radio housing assembly and
secure the units to the kit using the
screws supplied with the units.
(Figure B)
4. Reassemble dash in reverse order
of disassembly.
Stacked ISO units head provision
(Figure A)
(Figure B)

Notes

Notes

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 95-7323
REV. 5/17/11