Metra Electronics 99-9302 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-9302
99-9302
BMW
Mini Cooper/Cooper S 2002-2007
KIT FEATURES
•Mounting bracket
A) Mounting Bracket
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • T-33 Torx Driver
1-800-221-0932
©COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION
www.metraonline.com
TOOLS REQUIRED:
APPLICATIONS

Dash Disassembly
- BMW Mini Cooper/Cooper S 2002-2007 . . . . . . . . . . . . . . . 1,2
Kit Assembly
-DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Final Assembly ...........................................4
TABLE OF CONTENTS
99-9302
*Note:
Refer also to the instructions included with the aftermarket radio.

99-9302 DASH DISASSEMBLY
BMW Mini Cooper/Cooper S 2002-2007
A
B
C
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Carefully pry out both top edges of
driver’s knee panel and allow panel to
hang. ( Figure A)
2
Remove (2) Torx T-33 screws from
driver’s side rail trim. (Figure B)
3
Remove (2) Torx T-33 screws from
passenger side rail trim. (On specially
equipped models, it may be necessary
to open the glove box to access these
(2) screws) (Figure C)
4

99-9302 DASH DISASSEMBLY
BMW Mini Cooper/Cooper S 2002-2007
D
E
F
G
2
Remove (1) Phillips scew from each
cup holder. ( Figure D)
5
Carefully pry up mirror adjustment
switch panel and remove (2) Phillips
screws. ( Figure E)
6
Slide cup holder/gear shift assembly
toward rear of car and carefully
remove side rail trims.
(Figure F)
7
Remove (4) Phillip screws securing
radio. Pull out radio, disconnect and
remove.
(Figure G)
8

99-9302 KIT ASSEMBLY
3
A
B
DIN MOUNT RADIO PROVISION
Slide the DIN cage into the radio open-
ing of the Radio Housing and secureby
bending the metal locking tabs out-
ward.
(Figure A)
1
Slide the aftermarket radio unit into the
cage until it snaps into place. (Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-9302 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factorywiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) .............Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
4

NOTES
5
99-9302

99-9302 INSTRUCTIONS
1-800-221-0932
REV. 06/19/07 © COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION INST99-9302
www.metraonline.com