Metra Electronics METRA 99-7603 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7603
99-7603
APPLICATIONS
Nissan Versa
2007-2011
KIT FEATURES
•DIN Mount Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
• Double DIN Mount Radio Provision
•Stacked ISO Mount Units Provision
A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Trim Plate
Harness & Antenna Connections (sold separately)
•70--7552 - Nissan Harness 07-up
•40-NI12 - Nissan Adapter 07-up
KIT COMPONENTS
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver
1-800-221-0932
©COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
D
C

Dash Disassembly
- Nissan Versa 2007-2011... .................. . . . . . . 1,2
Kit Assembly
- DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 3
-ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4
-Double DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
-Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Final Assembly ...........................................7
TABLE OF CONTENTS
99-7603
*Note:
Refer also to the instructions included with the aftermarket radio.

99-7603 DASH DISASSEMBLY
NISSAN VERSA 2007-2011
A
B
C
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the panel above
the radio. ( Figure A,B)
2
Remove (2) Phillips screws securing
the radio trim panel then unclip and
remove the entire panel surrounding
the radio and a/c controls.
(Figure C)
3

99-7603 DASH DISASSEMBLY
NISSAN VERSA 2007-2011
D
E
VOL
CD
LOAD
SCRL
AUDIO
SCAN
CAT CH
AUX
6CD CHANGER
RPT
RDM
DISP
CLOCK
RADIO
PRESET A-B-C
SEEK
TRACK
FILE
TUNE
FF-REW
FOLDER
PWR
PUSH
1
2
3
4
5
6
2
Remove (4) Phillips screws securing
radio, unplug and remove radio.
(Figure D)
4
Remove (4) Phillips screws securing
each bracket to factory radio. (Retain
these brackets to be re-used during
double DIN or stacked ISO kit assem-
bly.)
(Figure E)
5
Continue to kit assembly.

99-7603 KIT ASSEMBLY
3
A
B
DIN MOUNT RADIO PROVISION
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
Note: You will need to remove the
aftermarket radio’strim ring if
equipped.
1
Slide the aftermarket radio into the
cage until it snaps into place. (Figure B)
2
Attach the trim plate supplied with the
kit to the front of the radio housing
assembly.
(Figure B)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7603 KIT ASSEMBLY
4
FRONT
FACE-
RIGHT
SIDE
BRACKET
A
B
C
ISO MOUNT RADIO PROVISION
Mount the ISO Brackets to the after-
market radio using the screws sup-
plied with the radio. (Figure B)
1
Note: The following modification
will need to be made to both
ISO brackets when using the ISO
mount radio provision. Cut or trim
the area shown from the ISO
bracket. (Figure A)
Slide the radio into the radio housing
until it snaps into place. (Figure C)
2
Attach the trim plate supplied with
the kit to the front of the radio hous-
ing assembly. (Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7603 KIT ASSEMBLY
5
A
B
DOUBLE DIN MOUNT RADIO PROVISION
Mount the factory brackets (removed
from factory radio during disassembly)
to the sides of the double DIN radio
using screws supplied with the double
DIN radio.
(Figure A)
1
Place the double DIN trim plate on the
front of the double DIN radio. (Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7603 KIT ASSEMBLY
6
A
B
STACKED ISO UNITS PROVISION
Mount the factory brackets (removed
from factory radio during disassembly)
to the sides of the stacked ISO units
using screws supplied with the ISO
units.
(Figure A)
1
Place the double DIN trim plate on the
front of the stacked ISO units. (Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7603 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown belowand the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7

NOTES
8
99-7603
I