Metra Electronics JP-1014 User manual

Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 12/12/19 INSTJP-1014
INSTALLATION INSTRUCTIONS
JP-1014
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• Driver and passenger specific dash replacement sealed speaker pods
to install 6” to 6.75” speaker
• Mounting positions for Chrysler three hole mount used by specific
speaker manufacturers such as Alpine
• Sealed enclosure with a hole for the factory wiring grommet
• Includes necessary speaker harness adapter
KIT COMPONENTS
• A) Speaker pods (L&R) • B) Speaker harness adapter (2)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 8mm, 10mm, socket wrench
TABLE OF CONTENTS
Dash Disassembly ..............................................2-6
Kit Assembly ..........................................................7
Jeep Wrangler (JL) 2018, Wrangler 2019-Up
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
A B

1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and remove the panel below the
steering column. Remove (2) Phillips
screw exposed. (Figures A,B)
2. Unclip, unplug, and remove the climate
control panel. (Figure C)
(Figure D)
(Figure E)
3. Remove (2) Phillips screws securing
the radio trim panel, then unclip and
remove. (Figure D)
4. Remove (1) Phillips screw securing the
dash pad, then unclip and remove.
(Figure E)
(Figure A)
(Figure B)
(Figure C)

REV. 12/12/2019 INSTJP-1014 3
DASH DISASSEMBLY
5. Remove (8) Phillips screws securing the
instrument panel on the left side, and
airbag panel on the right side.
(Figure F, G)
6. Unclip the steering column shroud then
set aside. (Figure H)
Driver’s side speaker removal:
7. Open the driver’s door, then unclip
and remove the panel on the side of
the dash. Remove (5) Phillips screws
exposed. (Figure I)
8. Remove (5) Phillips screws securing the
speaker panel, then unclip and remove.
(Figure J)
(Figure I)
(Figure F)
(Figure G)
(Figure H) (Figure J)

1.800.221.0932
|
MetraOnline.com
4
DASH DISASSEMBLY
9. Remove (4) 10mm screws and (1) 8mm
screw securing the dashboard brace.
The brace only needs loosened to aid in
removing the speaker pod in the next
step. (Figure K, L)
(Figure L) (Figure N)
(Figure M)(Figure K)
10. Remove (3) Phillips screws securing
the speaker pod, then unclip, unplug,
and remove. Gentle aggression will be
required to remove the pod. (Figure M)
Note: There is an electronic module
attached to the back of the pod which
must be removed and reused in
Kit Assembly. (Figure N)

REV. 12/12/2019 INSTJP-1014 5
DASH DISASSEMBLY
Passenger side speaker removal:
11. Open the passenger door, then unclip
and remove the panel on the side of
the dash. Remove (5) Phillips screws
exposed. (Figure O)
12. Starting from the right side, unclip and
remove the trim panel from the grab-
bar. Remove (2) 10mm screws securing
the grab-bar, then remove. (Figure P)
13. Unclip and remove the airbag trim
panel, then remove (2) Phillips screws
exposed. (Figure Q)
14. Open the glovebox, then unclip the
hinge and drop the glovebox. Remove
(3) Phillips screws exposed. (Figure R)
(Figure Q)(Figure O)
(Figure R)(Figure P)

1.800.221.0932
|
MetraOnline.com
6
(Figure S)
15. Looking in the glovebox cavity up high,
remove (2) 13mm screws securing the
back of the passenger side airbag.
(Figure S))
16. Unclip and slightly release the airbag
panel, just enough to expose (3) Phillips
screws securing the passenger side dash
panel. Remove the (3) screws.
(Figures T, U)
DASH DISASSEMBLY
(Figure U)
(Figure T) (Figure V)
17. Carefully unclip and pull out on the
dashboard panel just enough to expose
the speaker pod. Remove (3) Phillips
screws securing the pod, then unclip,
unplug and remove. (Figure V)
Continue to Kit Assembly

REV. 12/12/2019 INSTJP-1014 7
KIT ASSEMBLY
1. Remove the factory speakers from the
speaker pods. (Figure A)
2. Remove the grommet and factory
wiring from the speaker pods. (Figure B)
3. Insert the grommets into the JP-1014
speaker pods. (Figure C)
4. Attach the speaker harnesses provided
to the factory harness inside the pods,
and then to the aftermarket speaker.
(Figure D)
5. Secure the aftermarket speakers to the
pods using hardware supplied with
the speakers.
6. Reassemble the dash in reverse order
of disassembly. Ensure that the factory
electronic module removed in Dash
Disassembly, step 10, is connected back
to the vehicle.
(Figure A) (Figure C)
(Figure B) (Figure D)

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 12/12/19 INSTJP-1014
INSTALLATION INSTRUCTIONS
JP-1014
If you are having difficulties with the installation
of this product, contact our Tech Support line
either by phone at 386-257-1187, or email at
[e-mail]. Before
doing so, look over the instruction booklet a
second time and ensure that the installation was
performed exactly as the instruction booklet
is stated. Have the vehicle apart and ready to
perform troubleshooting steps before contacting
Metra/Axxess Tech Support.