Metra Electronics 99-5823CH User manual

APPLICATIONS
KIT FEATURES
KIT COMPONENTS
TOOLS REQUIRED
INSTALLATION INSTRUCTIONS FOR PART 99-5823CHINSTALLATION INSTRUCTIONS FOR PART 99-5823CH
FORD MUSTANG
2010-11
99-5823CH
• DIN Head unit provisions with pocket
• ISO DIN Head unit provision with pocket
• DDIN Head unit provision
• ISO Stacked Head unit provision
• Painted charcoal to match factory fi nish
• A) Radio Trim Panel • B) Radio Housing • C) ISO Brackets • D) ISO Trim Plate
• E) DDIN Brackets • F) DDIN Trim Plate • G) Pocket • H) (4) Panel Clips • I) A/C Harness
• Phillips Screwdriver • Panel Removal Tool
• Small Flat Blade Screwdriver
WIRING & ANTENNA CONNECTIONS (SOLD SEPARATELY)
• XSVI-5520-NAV FORD INTERFACE 2006-UP
•40-CR10 CHRYSLER/GM ANTENNA ADAPTER 2002-UP
A B C DE
F
G
H
I
(NON-NAV MODELS)

FORD MUSTANG 2010-11
99-5823CH DASH DISASSEMBLY
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
Unclip and remove the trim panel
surrounding the shifter including the
cup holders.
Remove (2) 9/32” screws from the
bottom of the radio panel then unclip
and remove the panel.
Remove (4) Phillips screws securing
the radio.
Remove panel clips from factory
Radio, or use the provided panel
clips, and attach them to the back of
the radio housing.
1
2
3
A
B
C
4
5
Continue to Kit Assembly

Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapters from
Metra and AXXESS to integrate your
new radio. Re-connect the negative
battery terminal and test the unit for
proper operation.
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down.
(Fig. A)
Snap the pocket into the bottom
opening of the radio housing.
(Fig. B)
Slide the aftermarket head unit into
the cage and secure. (Fig. B)
Plug the A/C harness into the car
side of the climate control plug and
the other side into the kit
Reassemble dash in reverse order
of disassembly using the 99-5823CH
radio trim panel instead of the factory
radio trim panel.
99-5823CH KIT ASSEMBLY
1
2
3
4
5
6
FORD MUSTANG 2010-11
DIN HEAD UNIT PROVISION
A
B

Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapters from
Metra and AXXESS to integrate your
new radio. Re-connect the negative
battery terminal and test the unit for
proper operation.
Mount the ISO Brackets to the head
unit with the screws supplied with the
unit. (Fig. A)
Snap the pocket into the bottom
opening of the radio housing.
(Fig. B)
Slide the head unit into the radio
opening until the side clips engage.
(Fig. B)
Snap the Trim plate into the Radio
Housing. (Fig. C)
Plug the A/C harness into the car side
of the climate control plug and the
other side into the kit
Reassemble dash in reverse order
of disassembly using the 99-5823CH
radio trim panel instead of the factory
radio trim panel.
99-5823CH KIT ASSEMBLY
1
2
3
4
5
6
7
FORD MUSTANG 2010-11
ISO DIN HEAD UNIT PROVISION
A
B
C
99-5823CH
MAIN SCREEN TEXT CUSTOMIZATION
1. Press and hold the MAX A/C button for 10 seconds. The current home
screen will then be displayed and the cursor will appear and blink. It will
be located in the 1st location on the top row.
2. To modify the text :
A. Use the FAN buttons to move the cursor forward or back. The
location where the cursor is blinking is the location that the
character may be changed.
• FANDOWN=MoveCursoraheadonelocation
• FANUP=MoveCursorbackonelocation
B. To change the character where the cursor is currently blinking use
the TEMP buttons to progress through the character set.
• TEMPUP=Showthenextcharacter
• TEMPDOWN=Showthepreviouscharacter
3. To exit this mode:
A. Do not press ANY buttons for 15 seconds and it will timeout
automatically.
B. Press button other than the 4 mentioned above.
4. To erase any changes made to the default display – Press and hold down
the recirculation button button for 15 seconds. The “TAURUS” will once
again be the default display.
NOTE : Characters are saved into memory immediately whenever changes
are made.
NOTE:Whileinthismode–nootherdisplayitemswillbeupdated.

C
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapters from
Metra and AXXESS to integrate your
new radio. Re-connect the negative
battery terminal and test the unit for
proper operation.
Cut and remove the center bar from
the radio housing. (Fig. A)
Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate. (Fig. B)
Slide the Double DIN head unit or
stacked ISO head units into the
bracket/radio housing assembly and
secure the Double DIN head unit
or stacked ISO head units to the
assembly using the screws supplied
with the radio. (Fig. C)
Snap the double DIN trim plate into
the radio housing.
Plug the A/C harness into the car
side of the climate control plug and
the other side into the kit
Reassemble dash in reverse order
of disassembly using the 99-5823CH
radio trim panel instead of the fac-
tory radio trim panel.
99-5823CH KIT ASSEMBLY
1
2
3
4
5
6
7
A
B
FORD MUSTANG 2010-11
DDIN / STACKED ISO DIN
HEAD UNIT PROVISION
99-5823CH
Changing The Display Back Light Color
Press the Passenger Heated Seat button for 10 seconds, the unit will go1.
into“ConfigureBacklightColor”mode.Thedisplaywillshow“RedGreen
Blue” with number assigned to each color contributing to the overall back
light color while in this mode. Each number will be between 0-255.
Press and hold the Fan + button to increase Red.2.
Press and hold the Fan - button to decrease Red.3.
PressandholdtheFrontDefrostbuttontoincreaseGreen.4.
PressandholdthePowerbuttontodecreaseGreen.5.
Press and hold the Rear Defrost button to increase Blue.6.
Press and hold the Driver Heated Seat button to decrease Blue.7.
After you choose your color stop pressing the buttons and after 108.
seconds the color chosen will stay.
Changing The Display Contrast
Press the Driver Heated Seat button for 10 seconds, the unit will go into1.
“ConfigureDisplayContrast”mode.
Press the Temp +/- buttons to adjust the display contrast up and down.2.
After 10 seconds of no buttons being pressed the chosen contrast will3.
stay.
METRA ACCESSORIES STEREO DASH KITS