Metra Electronics 99-7308 User manual

KIT COMPONENTS
99-7308
INSTALLATION
INSTRUCTIONS
APPLICATIONS
CAR PAGE
HYUNDAI
Accent 1995-99....................................1
Accent 2002-05....................................1
Elantra (single DIN) 1996-00............... 1
Sonata (Single DIN) 1995-98............... 2
Tiburon (single DIN) 1997-02.............. 2
KIT FEATURES
Shaft and
DIN head
unit provisions
TOOLS REQUIRED
Cutting tool
Adjustable wrench
Phillips screwdriver
Radio Housing
Spacer 1L
Spacer 1R
(4) #10 x ¾" Phillips
Truss-head Screws
3
ALL VEHICLES
2-SHAFT HEAD UNITS: Slide the aftermarket
head unit into the Radio Housing and secure
with shaft nuts. (see Fig. A).
DIN HEAD UNITS: Cut and remove the shaft
supports from the Radio Housing. Slide the DIN
cage into the kit and secure by bending the metal
locking tabs down. Slide the aftermarket head
unit into the cage until secure. (see Fig. B)
Fig. A
Fig. A
Fig. B
5
ACCENT: Re-connect the battery terminal and test the unit for proper operation. Mount the
head unit/kit assembly to the sub-dash with (4) Phillips screws previously removed in step #1.
ELANTRA, TIBURON: Re-connect the battery terminal and test the unit for proper operation.
Mount the head unit/kit assembly to the sub-dash with (4) #10 x ¾" Phillips Truss-head
Screws supplied.
SONATA: Re-connect the battery terminal and test the unit for proper operation. Mount the
factory pocket to the sub-dash with (4) Phillips screws previously removed in step #1.Mount
the head unit/kit assembly to the sub-dash with (4) Phillips screws previously removed in step
#1. (see Fig. A).
4
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
3
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-07 METRA ELECTRONICS CORPORATION
rev. 06-14-07

Fig. A
"A"
"1R"
2
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Pop out the
dimmer switch panel and remove (1) Phillips screw
exposed. Unsnap the gear shifter trim plate and
remove (1) Phillips screw exposed at the base of
the dash trim bezel. Reach under the driver's side
dash, locate the teperature control cable and
remove the cable from the white plastic bracket.
Position the gear shifter in low, pull the dash panel
away and disconnect all wiring harnesses.
Remove the trim bezel (the temperature control
cable will be attached). Remove (4) Phillips
screws securing the factory head unit and
disconnect the wiring.
11
1
1
HYUNDAI Accent 1995-99 / 2002-2005 HYUNDAI Sonata (single DIN) 1995-98
HYUNDAI Elantra (single DIN) 1996-00 HYUNDAI Tiburon (single DIN) 1997-02
Locate the Radio Housing. Skip to the
Installation Instructions for ALL VEHICLES
on Page #3.
Locate the Radio Housing. Skip to the
Installation Instructions for ALL VEHICLES
on Page #3.
Attach Spacer 1L to the left mounting tab of
the Radio Housing and Spacer 1R to the
right mounting tab of the Radio Housing as
shown. Skip to the Installation Instructions
for ALL VEHICLES on Page #3.
Attach Spacer 1L to the left mounting tab of
the Radio Housing and Spacer 1R to the
right mounting tab of the Radio Housing as
shown. Skip to the Installation Instructions
for ALL VEHICLES on Page #3.
22
2
2
Disconnect the negative battery terminal to prevent
an accidental short circuit. For 2002-05 models
Disconnect (2)
posed.
vent cables from the vent levers
located behind the driver's side dash. Unclip the
dash trim bezel and disconnect the wiring. Remove
(4) Phillips screws securing the factory head unit
and disconnect the wiring.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the gear shifter trim panel and remove (1)
screw exposed. Unclip the dash trim bezel
and remove. Remove (4) Phillips screws
securing the factory head unit and
disconnect the wiring. Cut and remove tabs
"A" located in the top corners of the dash
cavity.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
(4) Phillips screws securing the center
console. Pry out on the front edge of the
console and unclip the radio trim bezel.
Remove (2) Phillips screws securing the
factory pocket and remove. Remove (4)
Phillips screws securing the factory head
unit and disconnect the wiring.
"1L"
"1R"
Remove the ashtray and (2) Phillips screws ex-
Remove (2) Phillips screws inside cupholders.
"1L"