Metra Electronics 99-8214TB User manual

INSTALLATION INSTR CTIONS FOR PART 99-8214
hillips Screwdriver • Small Flat Blade Screwdriver • Socket Wrench
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
• DIN Head Unit rovision With ocket
• ISO DIN Head Unit rovision With ocket
• Double DIN Head Unit rovision
• Stacked ISO DIN Head Unit rovision
• ainted And Textured To Match Factory Dash
• Available In Two Colors:
99-8214TB = BLACK, 99-8214TG = GRAY
• Both kits are factory “golf ball” style
textured.
• A) Radio Housing • B) Radio Housing Brackets
KIT COM ONENTS
AB
CD
APPLICATIONS
Toyota Tacoma 2005-2011
• C) Radio Housing Trim anel • D) ISO Brackets
• E) ISO Trim late • F) (4) #6 x 3/8” hillips an Head Screws
• G) (4) #8 X 3/8” hillips Truss Head Screws • H) Double DIN Trim late • I) Clock/Hazard Switch Bracket
E
F
G
H
99-8214TB
99-8214TG
TOOLS REQUIRED:
I
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1761 - Toyota arness 1987-up
• TYTO-01 - Toyota amp interface arness 2003-up
Antenna Adapter:
• Not required

Dash Disasse bly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Kit Asse bly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,4,5,6
Final Asse bly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TABLE OF CONTENTS
99-8214
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills
by enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 for more information
and take steps toward a better tomorrow.

99-8214
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove A/C control panel.
(Figure A)
2
TOYOTA TACOMA 2005-2011
Remove (4) 10 MM bolts securing
radio.
(Figure B)
3
Unclip and remove entire panel
including hazard switch and clock.
(Figure C)
4
Remove the left and right radio
brackets from the radio chassis.
(Figure D)
5
Unclip and remove the clock/hazard
switch assembly from the factory
radio housing trim panel. (Figure E)
6
DASH DISASSEMBLY
SCAN
TEXT
PWR VOL
SCAN
TEXT
PWR VOL
A
B
C
D
Continue to Kit Preparation.
E

2
99-8214
TACOMA 2005-2011
KIT PREPARATION
Clip the clock/hazard switch
assembly into the 99-8214 Radio
Housing Trim anel. (Figure A,B)
2
A
H
M
PASSENGERPASSENGER
INSERT CLOCK/HAZARD SWITCH ASSEMBLY
FROM REAR OF 99-8214 RADIO HOUSING TRIM PANEL
H
M
PASSENGER PASSENGER
B
Continue to Kit Assembly.
Attach the clock/hazard switch
bracket to the radio housing using
the (4) #6 x 3/8” hillips pan head
screws.
WARNING:
DO NOT OVERTIGHTEN SCREWS.
1
(SKIP KIT PREPARATION WHEN INSTALLING DDIN RADIO)

99-8214
KIT ASSEMBLY
TOYOTA TACOMA 2005-2011
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure B)
2
Slide the aftermarket head unit into
the cage and secure.
(Figure C)
3
Secure the Radio Housing into the
dash using the factory hardware.
4
DIN HEAD NIT PROVISION
B
C
3
A
Attach the corresponding radio
housing bracket to the radio housing
using the included (4) #8 x 3/8”
1
Continue to Final Assembly.

99-8214
KIT ASSEMBLY
TOYOTA TACOMA 2005-2011
Attach the corresponding radio
housing bracket to the radio housing
using the included (4) #8 x 3/8”
hillips truss head screws. (Figure A)
1
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure B)
2
Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
3
Snap the ISO Trim late into the
Radio Housing.
(Figure C)
4
Secure the radio housing into the
dash using the factory hardware.
5
ISO DIN HEAD NIT PROVISION
A
B
C
4
Continue to Final Assembly.

5
Slide the aftermarket radio unit into
the factory brackets and secure the
unit to the brackets using the
screws supplied with the head unit.
(Figure A)
1
A
B
REMOVE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
REMOVE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
REAR VIEW OF RADIO HOUSING
D
RESTORE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
RESTORE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
REAR VIEW OF
RADIO HOUSING
DOUBLE DIN TRIM PLATE
C
Secure the aftermarket radio unit
and factory bracket assembly into
the sub dash. (Figure B)
2
DO BLE DIN HEAD NIT PROVISION
3
lace the Double DIN trim plate into
the back of the radio housing, then
attach the clock/hazard switch brack-
et assembly using the (4) #6 x 3/8”
hillips pan head screws.
(Figure C)
WARNING:
DO NOT OVERTIGHTEN SCREWS.
4
99-8214
KIT ASSEMBLY
Continue to Final Assembly.
Clip the clock/hazard switch
assembly into the 99-8214 Radio
Housing Trim anel. (Figure D)

6
Slide the aftermarket radio units into
the factory brackets and secure the
unit to the brackets using the
screws supplied with the head unit.
(Figure A)
1
Secure the aftermarket radio units
and factory bracket assembly into
the sub dash. (Figure B)
2
STACKED ISO DIN HEAD NIT PROVISION
99-8214
KIT ASSEMBLY
A
B
REMOVE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
REMOVE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
REAR VIEW OF RADIO HOUSING
C
RESTORE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
RESTORE
CLOCK/HAZARD SWITCH
BRACKET ASSEMBLY
REAR VIEW OF
RADIO HOUSING
DOUBLE DIN TRIM PLATE
D
Remove the (4) screws securing the
clock/hazard switch bracket to the
radio housing and remove the
clock/hazard switch bracket
assembly.
(Figure C)
3
lace the Double DIN trim plate into
the radio housing and replace the
clock/hazard switch/bracket assem-
bly using the (4) #6 x 3/8” hillips
pan head screws.
(Figure D)
4
Continue to Final Assembly.

7
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
99-8214
FINAL ASSEMBLY
Make wiring onne tions using the EIA olor ode hart shown below and the instru tions in luded with the head
unit. Metra re ommends making onne tions as shown below; Strip, Spli e, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent ele tri al short ir uit.
12V Ignition / A . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Bla k*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Bla k / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray / Bla k
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Bla k
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Bla k
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Bla k
*NOTE: When Bla k a wire is not present, ground radio to vehi le hassis.
All olors may not be present on all leads due to manufa turer’s spe ifi ations.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS

8
NOTES
99-8214