Metra Electronics 99-7424 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7424
99-7424
APPLICATIONS
Nissan Titan 2008-11
KIT FEATURE
• DIN Radio Provision with Pocket
• I O Mount Radio Provision with Pocket
• Painted To Match Factory Dash
A) ingle DIN Radio Housing • B) I O Trim Plate • C) I O Brackets • D) Trim Panel
• E) Two ided Tape (Not hown)
KIT COMPONENT
A
TOOL REQUIRED:
Torx T-10 Driver • mall Flat Blade crewdriver/ Panel Removal Tool
• Phillips crewdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
D
BC
Harness & Antenna Connections (sold separately)
• 70-7550 - Nissan Harness 95-up

Das Disassembly
Nissan Titan 2008-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 2
Kit Assembly
- DIN Radio Provision wit Pocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- ISO Mount Radio Provision wit Pocket. . . . . . . . . . . . . . . . . . . . . . . .4
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TABLE OF CONTENTS
99-7424
*Note:
Refer also to the instructions included with the aftermarket radio.

99-7424 DASH DISASSEMBLY
NISSAN Tit n 2008-11
A
B
C
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip the entire dash panel including
the radio and climate controls. Unplug
and remove the panel. (Figure A)
2
Remove (4) Phillips screws securing
the radio chassis. Unplug and remove
the chassis.
(Figure B)
3
Remove (4) T-10 Torx screws securing
the climate controls to the dash panel
and remove the controls from the
panel. (Retain the screws and climate
controls for re-use during kit prepara-
tion.) (Figure C)
4
Remove (2) T-10 Torx screws securing
the passenger air bag status light
assembly to the dash panel and
remove the light from the panel.
(Retain the screws and light for re-
use during kit preparation.)
(Figure C)
NOTE: The small round Airbag s icker
also needs o be removed from he fac-
ory panel and placed on o he 99-7424
radio housing panel. (A round piece of
double-sided ape is provided in case
he fac ory s icker is no s rong
enough.) (Figure C)
5
Continue to kit preparation

2
99-7424 KIT PREPARATON
Attach the climate controls to the Trim
Panel using the factory hardware
removed during the dash disassem-
bly.
(Figure A)
1
Attach the passenger air bag status
light assembly to the Trim Panel using
the factory hardware removed during
the dash disassembly. Also, apply to
air bag button the small round airbag
sticker previously removed in tep 5
dash disassembly.
(Figure B)
2
Continue to kit assembly.
A
B
NISSAN Tit n 2008-11

3
99-7424 KIT ASSEMBLY
DIN RADIO PROVISION WITH POCKET
lide the DIN cage into the ingle DIN
Radio Housing and secure by bending
the metal locking tabs outward.
1
lide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
2
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B

4
99-7424 KIT ASSEMBLY
A
B
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the I O Brackets to the radio
using the screws supplied with the
radio.
(Figure A)
1
lide the radio into the radio housing
until it snaps into place.
(Figure B)
2
nap the Trim plate onto the front of
the Radio Housing.
(Figure B)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

5
99-7424 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends toget er
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble in reverse order of disassembly using the 99-7424 Trim Panel in
place of the factory radio trim panel.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring onne tions using the EIA olor ode hart shown below and the instru tions in luded with the
head unit. Metra re ommends making onne tions as shown below; Strip, Spli e, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent ele tri al short ir uit.
METRA / EIA WIRING CODE
12V Ignition / A . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Bla k*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Bla k / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Bla k
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Bla k
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Bla k
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Bla k
*NOTE: When a Bla k wire is not present, ground radio to vehi le hassis.
All olors may not be present on all leads due to manufa turer’s spe ifi ations.

99-7424 INSTRUCTIONS
1-800-221-0932
REV. 11/18/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7424
www.metraonline.com