Metra Electronics 99-7864 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7864
99-7864
KIT FEATURES
•DIN Radio Provision
•ISO Radio Provision
A) Radio/Climate Control Housing B) ISO Brackets C) ISO Trim Plate D) PPH-1034 Screws
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ • Panel Removal Tool
•Phillips Screwdriver
1-800-221-0932
©COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
TOOLS REQUIRED:
APPLICATIONS
Honda Accord
2003-2007
(Equipped with Single Zone Climate Controls)
BCD
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
WIRING HARNESS:
•70-1721 - Honda/Acura Harness 1998-up
•70-78640Z - AccordDual Zone Eliminator Harness 2003-07
ANTENNA ADAPTER:
Not Required

Dash Disassembly
-HondaAccord2003-2007 ..................................... .1,2
Kit Assembly
-DINRadioProvision .............................................3
-ISORadioProvision .............................................4
Final Assembly ..........................................5
TABLE OF CONTENTS
99-7864
*Note:
Refer also to the instructions included with the aftermarket radio.
NOTE:
Toadapt dual zone climate controls to a single zone system to work
with this kit you will need Metra harness #70-7864DZ (sold separately).
KNOWLEDGE IS POWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.

99-7864 DASH DISASSEMBLY
HONDA ACCORD 2003-2007
A
B
1
Disconnect the negative battery-
terminal to prevent an accidental
short circuit.
1
Unsnap and remove shift lever
trim ring. (Figure A)
2
Unsnap coin tray/ashtray from
assembly and remove. Rubber
cover may come out first but
entire assembly must be removed
to access screws below.
(Figure B)
3
Remove (2) Phillips screws from
under coin tray/ashtray and
remove entire assembly.
(Figure C)
4
Continue to kit assembly.
R
N
D
D
C
R
N
D
D
R
N
D
D

2
99-7864 DASH DISASSEMBLY
E
F
G
R
P
N
D
D
D
HONDA ACCORD 2003-2007
Remove (2) Phillips screws facing
up under radio/climate control
assembly.
)(Figure E)
6
Push and hold the hazard button
down. Carefully insert a flat blade
screwdriver into the slot below the
button and push down to release
the center clip.
(Figure F)
7
Unclip and remove radio/climate
control assembly.
9
Unsnap and remove upper panel
(including a/c vents) and remove (3)
Phillips screws behind the panel.
(Figure G)
8
Tip: You can use a hook tool to
grasp the panel inside of the vent
and pull toward the rear of the vehi-
cle. Be careful not to scratch the
panel.
Continue to kit assembly.
* Note: Refer also to the instructions included with the aftermarket radio.
Remove (2) Phillips screws from
bottom of pocket assembly and
unsnap and remove. (Figure D)
5

3
99-7864 KIT ASSEMBLY
B
A
DIN RADIO PROVISION
Slide the aftermarket radio into the
cage and secure.
(Figure B)
2
Continue to final assembly.
* Note: Refer also to the instructions included with the aftermarket radio.
Snap the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. ( Figure A)
1
Programming:
In order to adjust the 99-7864 to
the different types of radios
available in the Honda Accord,
the 99-7864 has a program fea-
ture.
4DOOR SEDAN ONLY:
To program the kit you will need
to start your vehicle then hold
the A/C button for approximately
5seconds or until the light starts
to blink.The climate controls will
be programmed when the light
stops blinking.
2DOOR COUPE ONLY:
Toprogram the kit you will need
to start your vehicle then hold
the Rear Defrost button for
approximately 5 seconds or until
the light starts to blink.
The climate controls will be
programmed when the light
stops blinking.
Note:
The orange wire coming out of
the back of the 99-7864 needs to
be connected to the orange illu-
mination wire coming from the
Metra 70-1721 wire harness (sold
separately).

4
99-7864 KIT ASSEMBLY
B
A
ISO RADIO PROVISION
Slide the head unit into the radio
opening until the side clips engage.
Snap the Trim plate into the Radio
Housing.
(Figure B)
2
Continue to final assembly.
* Note: Refer also to the instructions included with the aftermarket radio.
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. ( Figure A)
1
NOTE:
When reinstalling the screws
into the bottom of the 99-7864
use the (2) supplied Phillips
screws instead of the factory
screws removed in step 5 in
Dash Disassembly.
Programming:
In order to adjust the 99-7864 to
the different types of radios
available in the Honda Accord,
the 99-7864 has a program
feature.
2DOOR COUPE ONLY:
To program the kit you will need
to start your vehicle then hold
the Rear Defrost button for
approximately 5 seconds or until
the light starts to blink.The cli-
mate controls will be pro-
grammed when the light stops
blinking.
4DOOR SEDAN ONLY:
To program the kit you will need
to start your vehicle then hold
the A/C button for approximately
5seconds or until the light starts
to blink.The climate controls will
be programmed when the light
stops blinking.
Note:
The orange wire coming out of
the back of the 99-7864 needs to
be connected to the orange illu-
mination wire coming from the
Metra 70-1721 wire harness (sold
separately).

99-7864 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
NOTE: Use the screws supplied with this kit for the lower mounting
screws instead of the factory hardware.
1
2
3
5
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown belowand the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’sspecifications.

99-7864 INSTRUCTIONS
1-800-221-0932
REV. 05/04/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-7864
www.metraonline.com