Metra Electronics 99-3010S User manual

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

INSTALLATION INSTRUCTIONS

99-3010S

KIT FEATURES

• DIN radio provision with pocket

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted silver to match the factory ﬁnish

KIT COMPONENTS

• A) Radio trim panel with climate controls • B) Radio housing • C) Pocket • D) ISO DDIN brackets • E) ISO DDIN trim plate • F) ISO trim plate

• G) ISO brackets • H) Axxess interface and harness (not shown) TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 9/32” socket wrench • T-20 Torx screwdriver

• Cutting tool

TABLE OF CONTENTS

Dash Disassembly ...............................................2-3

Kit Preparation .......................................................3

Kit Assembly

–DIN radio provision with pocket ........................4

–ISO DIN radio provision with pocket ..................4

–ISO DDIN radio provision .....................................5

Axxess Interface Installation .................................6

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Axxess interface included

Antenna Adapter: 40-EU55 (sold sep.)

Steering wheel control interface: ASWC-1 (sold sep.)

Backup camera retention: BACKUPCAM-2 (sold sep.)

A B C E

Chevrolet Camaro 2010-2015

■

1.800.221.0932

MetraOnline.com

For vehicles without UMQ gauge panel,

unsnap and remove shifter trim panel

and skip to step 8.

1. Unclip and remove the (2) side trim

panels running the length of the center

console. (Figure A)

2. Remove (1) Phillips screw from each

side of the front of the center console.

(Figure B)

3. Remove (2) Phillips screws per side

from the cover on the back of the center

console then unclip and remove the

cover. (Figure C)

(Figure D)(Figure A)

(Figure E)(Figure B)

(Figure F)(Figure C)

70 9

180

200

320

300

100

70 9

180

200

320

300

100

70 9

180

200

320

300

100

70 9

180

200

320

300

100

DASH DISASSEMBLY

4. Remove (2) Phillips screws exposed

under the cover on the back of console.

(Figure D)

5. Remove gauge cluster/trim panel

around shifter. (Figure E)

6. Auto transmission vehicles only:

Remove one T-20 Torx screw from the

front of the shifter, and then remove

the knob and shifter surround panel.

(Figure F)

Continue onto next page

■

1"'elra».

REV. 5/25/2018 INST99-3010S 3

(Figure G)

(Figure H)

(Figure I)

DASH DISASSEMBLY KIT PREPARATION

(Figure A)

(Figure B)

7. Remove (4) Phillips screws now

exposed, and then lift up on the rear

of the center console. Slide toward

the back of the vehicle then unclip

and remove the entire center console.

(Figure G)

8. Remove (2) 9/32” screws securing the

climate control/radio trim panel and

remove. (Figure H)

9. Remove (4) 9/32” screws securing the

radio chassis, and then remove.

(Figure I)

Continue to Kit Preparation

1. Cut and remove the sub dash radio

support to make room for the interface

and harnesses. (Figure A)

2. Remove the panel clips from the factory

radio, then attach them to the 99-3010S

radio trim panel with climate controls.

(Figure B)

Continue to Kit Assembly

Remove shaded area

r i

■

1.800.221.0932

MetraOnline.com

DIN radio provision with pocket

1. Remove the metal DIN sleeve from the

aftermarket radio.

2. Slide the sleeve into the top opening

of the

radio housing

and secure by

bending the metal locking tabs down.

(Figure A)

3. Snap the

pocket

into the bottom

opening of the

radio housing

(Figure B)

4. Slide the radio back into the sleeve until

it clicks in. (Figure B)

Continue to Axxess

Interface Installation.

(Figure A)

(Figure B)

KIT ASSEMBLY

ISO DIN radio provision with pocket

1. Remove the metal DIN sleeve and trim

ring from the aftermarket radio.

2. Secure the

ISO brackets

to the radio

using the screws supplied with the

radio. (Figure A)

3. Snap the

pocket

into the bottom

opening of the

radio housing

(Figure B)

4. Slide the radio into the top opening of

the

radio housing

until it clicks in.

(Figure C)

5. Snap the

ISO trim plate

into the

radio

housing

. (Figure C)

Continue to Axxess

Interface Installation.

(Figure A)

(Figure B)

(Figure C)

■

1"'elra».

REV. 5/25/2018 INST99-3010S 5

ISO DDIN radio provision

1. Cut and remove the center support.

(Figure A)

2. Snap the

ISO DDIN brackets

to the

inside edge of the

radio housing

(Figure B)

3. Slide the radio into the bracket/radio

housing assembly, then secure it using

the screws supplied with the radio.

(Figure C)

4. Snap the

ISO DDIN trim plate

into the

radio housing

. (Figure C)

Continue to Axxess

Interface Installation.

(Figure C)(Figure A) (Figure B)

KIT ASSEMBLY

Remove shaded area

■

1.800.221.0932

MetraOnline.com

AXXESS INTERFACE INSTALLATION

INTERFACE FEATURES

INTERFACE COMPONENTS

• Axxess interface

• 3010 harness

• Climate control harness

• 16-pin harness with stripped leads

• 4-pin to 4-pin resistor pad harness

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder, and heat shrink

• Small ﬂat blade screwdriver • Tape • Wire cutter • Zip ties

TABLE OF CONTENTS

Connections to be made ..........................................................................................................7-10

For models without an ampliﬁer ........................................................................................7-8

For models with an ampliﬁer ............................................................................................. 8-9

Installing the Axxess interface and climate controls ................................................................10

Programming the Axxess interface and climate controls ........................................................10

Adjusting the Axxess interface ....................................................................................................11

Final assembly ..............................................................................................................................11

Conﬁgure backlight color .............................................................................................................11

Troubleshooting ............................................................................................................................11

• Provides accessory power (12-volt 10-amp)

• Maintains the Retained Accessory Power (R.A.P.) feature

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains warning chimes

• Retains OnStar/OE Bluetooth

• Adjustable volume for chimes and OnStar

• Retains the factory AUX-IN jack

• Pre-wired ASWC-1 harness (ASWC-1 sold separately)

• Can be used in non-ampliﬁed, or ampliﬁed models

• Retains balance and fade

• Micro “B” USB updatable

■

1"elra»,.

REV. 5/25/2018 INST99-3010S 7

CONNECTIONS TO BE MADE

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire.

• Tape off and disregard the following (5) wires, they will not be used in this application:

Blue/White, Purple, Purple/Black, Green, Green/Black

From the 3010 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) Red wires

to accessory power.

• Cut off and remove the resistors from the Green, Green/Black, Purple, and Purple/Black

wires below the heat shrink.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

• Ensure the (2) 4-pin Molex connectors are connected together.

Note: The 4-pin to 4-pin resistor pad harness

will not

be used in this application.

Continued on the next page

Attention! This interface will work with models that are either non-ampliﬁed or ampliﬁed,

Please follow the instructions carefully for your model vehicle. Failure to do so will result in

either no sound, or low sound. If you are unsure if your vehicle is factory ampliﬁed or not,

please contact your local dealership.

For models

without

an ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

Note: If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2) Red

wires from the 3010 harness as well.

• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.

• If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is

not connected, the radio will turn off when OnStar is activated.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

■

1.800.221.0932

MetraOnline.com

CONNECTIONS TO BE MADE (CONT.)

• The Black/Yellow wire is used for OnStar level adjustment for models that do not come

equipped with steering wheel controls. Refer to the OnStar level Adjustment section for

further instructions.

Attention! If this wire is not connected the climate control will fail to function.

• Connect the Pink wire with a red bullet connector to the Pink wire from the

climate

control harness

• If retaining the factory AUX-IN jack is desired, connect the Red and White RCA jacks to the

audio AUX-IN jacks from the aftermarket radio.

Note:

a) The jack can only be used if it is a single jack.

b) If the jack has a USB port as well, neither can be retained.

Note: The relay attached to the 3010 harness is only for audible turn signal clicks.

No extra steps are required to retain this feature, so leave the relay as-is.

12-pin pre-wired ASWC-1 harness:

This harness is to be used along with the optional ASWC-1 (sold separately) to retain steering

wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If the ASWC-1

will be used, please refer to the ASWC-1 instructions for radio connections and programming.

Disregard the harness that comes with the ASWC-1.

DIN jack:

The DIN jack is to be used with the optional AX-LCD (sold separately) to retain the

personalization menu.

For models

with

an ampliﬁer:

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

Note: If installing either an ASWC-1 or AX-LCD (both sold separately), connect the (2)

Red wires from the 3010 harness as well.

• Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear

sound from the factory ampliﬁer.