Metra Electronics LEXUS 99-8150 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-8150
APPLICATIONS
LEXUS ES SERIES
1992-1996
KIT FEATURES
•DIN Mount Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
A) Radio Housing • B) Trim Plate • C) Mounting Brackets • D) ISO Brackets • E) (6) Phillips Screws
KIT COMPONENTS
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Set
1-800-221-0932
©COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
www.metraonline.com
99-8150
B
DC
E

Dash Disassembly
- Lexus ES Series 1992-1996 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Preparation ............................................2
Kit Assembly
-DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 3
-ISO Mount Radio Provision with Pocket....................... 4
Final Assembly ...........................................5
TABLE OF CONTENTS
99-8150
*Note:
Refer also to the instructions included with the aftermarket radio.

99-8150 DASH DISASSEMBLY
LEXUS ES SERIES 1992-1996
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the plastic trim
piece below the factory radio and
remove (2) Phillips screws exposed
underneath. ( Figure A)
2
Using a small flat blade screwdriver
release the clips securing the a/c vent
assembly and remove the assembly.
(Figure B)
3
Remove (2) Phillips screws inside of
vent cavity. (Figure B)
4
Pull the climate control/radio assem-
bly from the dash and disconnect the
wiring. (
Figure C)
5
Remove (2) Phillips screws and (4)
bolts per side to remove factory
brackets from climate controls and
radio.
6
Continue to kit assembly.
A
B
C

99-8150 KIT PREPARATION
2
Install the mounting brackets to the
radio housing with (6) Phillips
Screws supplied. ( Figure A)
1
Install the factory climate controls
into the assembled radio housing
and bracket assembly using the
screws from disassembly. ( Figure A)
2
Continue to kit assembly.
LEXUS ES SERIES 1992-1996
DIN MOUNT RADIO PROVISION WITH POCKET
ISO MOUNT RADIO PROVISON WITH POCKET
A

99-8150 KIT ASSEMBLY
3
Slide the DIN cage into the radio
housing and secure by bending the
metal locking tabs outward (Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure A)
2
Continue to final assembly.
LEXUS ES SERIES 1992-1996
DIN MOUNT RADIO PROVISION WITH POCKET
Note: Refer also to the instructions included with the aftermarket radio.
A

99-8150 KIT ASSEMBLY
4
Mount the ISO brackets to the radio
using the screws supplied with the
radio. (Figure A)
1
Slide the radio into the radio housing
until the ISO brackets snap into place.
(Figure A)
2
Snap the trim plate onto the front of
the radio housing. (Figure A)
3
NOTE: To remove the mounted after-
market radio, unclip and remove the
ISO trimplate. Using a small flat blade
screwdriver, disengage the side clips
securing the ISO brackets to the
Radio Housing.
(Figure B)
Continue to final assembly.
LEXUS ES SERIES 1992-1996
ISO MOUNT RADIO PROVISON WITH POCKET
Note: Refer also to the instructions included with the aftermarket radio.
A
B

99-8150 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) .............Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5

99-8150 INSTRUCTIONS
1-800-221-0932
REV. 07/28/10 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8150
www.metraonline.com