Metra Electronics 99-7877S User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7877S
99-7877S
APPLICATIONS
Honda Fit 2009-10
KIT FEATURES
•DIN Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
•Stacked ISO Mount Units Provision
•Painted ToMatch Factory Dash
“S”= SILVER
•A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
•E) Double DIN Trim Plate • F) Pocket
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Set
1-800-221-0932
©COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
BD
EF
C
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
•70-1729 Honda Harness 2008-up
•40-HD10 Honda Antenna Adapter 2005-up
TOOLS REQUIRED:

Dash Disassembly
- HondaFit2009-10............................. . . . . . 1
Kit Assembly
-Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
-DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
-ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4
-Double DIN Radio/ Stacked ISO Mount Units Provision ............. 5
TABLE OF CONTENTS
99-7877S
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.

99-7877S DASH DISASSEMBLY
HONDA FIT 2009-10
1
1
Remove (1) 8 MM bolt facing up
behind center panel.
Note: Slide the recirculation
control lever to FRESH for better
access to bolt. (
Figure A)
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
3
Unclip and remove the lower center
panel below radio. ( Figure A)
2
Remove (2) Phillips screws securing
the hazard switch to the back of the
factory radio panel. ( Figure D)
5
Remove (2) Phillips screws securing
the air bag light to the backof the
factory radio panel. ( Figure E)
6
Remove (5) Phillips screws securing
the a/c vents to the radio panel.
Remove (7) retaining clips from radio
housing to be used later in kit
preparation.
8
7
Open the upper glove box then use
apry tool to unclip and remove the
radio/climate control assembly.
(
Figure B & C)
4
Continue to kit preparation.
A
B
C
D
E

2
99-7877S KIT PREPARATION
KIT PREPARATION
1
Secure the a/c vents to the radio
housing using the factory hardware.
( Figure B)
Secure the hazard switch into the
radio housing panel using the factory
hardware. ( Figure A)
3
Attach the (7) retaining clips to the
radio housing panel in the same
location as removed from the factory
radio panel.
4
Secure the air bag light into the radio
housing panel using the factory
hardware. (
Figure A)
2
Continue to kit assembly.
A
B

99-7877S KIT ASSEMBLY
3
A
B
C
DIN MOUNT RADIO PROVISION WITH POCKET
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from
Metra or AXXESS. Re-connect the
negative battery terminal and test
the unit for proper operation.
1
Slide the DIN cage into the Radio
Housing and secureby bending the
metal locking tabs down. (Figure A)
2
Slide the aftermarket head unit into
the cage and secure.
(Figure B)
3
Snap the pocket into the Radio
Housing. (Figure C)
4
Re-assemble dash in reverse order of
disassembly.
5
*Note: Refer also to the instructions included with the aftermarket radio.

99-7877S KIT ASSEMBLY
4
ISO MOUNT RADIO PROVISION WITH POCKET
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
2
Slide the head unit into the radio
opening until the side clips engage.
(Figure B)
3
Snap the Trim plate into the Radio
Housing. (Figure B)
4
Snap the Pocket into the radio
housing.
(Figure C)
5
*Note: Refer also to the instructions included with the aftermarket radio.
Re-assemble dash in reverse order of
disassembly.
6
A
B
C

99-7877S KIT ASSEMBLY
5
DOUBLE DIN RADIO PROVISION/
Cut and remove the center bar from
the radio housing.
(Figure A)
2
Snap the Double DIN brackets to the
inside edge of the Radio Housing.
(Figure B)
3
Slide the Double DIN head unit or
stacked ISO head units into the
bracket/radio housing assembly and
secure the Double DIN head unit or
stacked ISO head units to the
assembly using the screws supplied
with the radio.
(Figure C)
4
Snap the Double DIN trim plate onto
the front of the radio/housing
assembly. (Figure C)
5
*Note: Refer also to the instructions included with the aftermarket radio.
STACKED ISO MOUNT UNITS PROVISION
A
B
C
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Re-assemble dash in reverse order of
disassembly.
6

99-7877S INSTRUCTIONS
1-800-221-0932
REV. 4/22/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7877
www.metraonline.com