Metra Electronics 99-8219 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-8219
Phillips Screwdriver Or Panel Removal Tool
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
APPLICATIONS
Toyota FJ Cruiser
2007-2009
•DIN radio provision with pocket
•ISO radio provision with pocket
KIT COMPONENTS
99-8219
A
B
C
D
TOOLS REQUIRED:
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
Wireharness:
•70-1761 Toyota 1987-up
Antenna adapter:
•Not required
•A) Radio Housing • B) Housing Brackets • C) ISO Snap In Brackets • D) Trim Plate

Dash Disassembly
-Toyota FJ Cruiser 2007-2009 . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly *
-DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 2
-ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 3
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
TABLE OF CONTENTS
99-8219
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake
steps towardabetter tomorrow.

1
99-8219 DASH DISASSEMBLY
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Remove two Phillips screws from
bottom part of side trim panels.
Figure A)
2
TOYOTAFJ CRUISER 2007-2009
Using a panel removal tool, carefully
remove the side trim panels.
(Figure B)
3
Remove (2) Phillips screws from radio
trim panel. (Figure C)
4
Using panel removal tool, carefully
remove radio trim panel.
(Figure D)
5
Remove (4) 10mm bolts securing the
radio.
6
7
A
B
C
D
Unplug and remove radio.
Continue to kit assembly.

2
99-8219 KIT ASSEMBLY
Slide the aftermarket radio into the
cage and secure. (Figure C)
3
Slide the housing brackets onto
the side of the radio housing until
the clips engage. Note: Brackets
are marked left and right. (Figure A)
1
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure B)
2
DIN RADIO PROVISION WITH POCKET
A
B
C
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

3
99-8219 KIT ASSEMBLY
Mount the ISO Brackets to the
aftermarket radio using the
screws supplied with the radio.
(Figure B)
2
Slide the radio into the radio
housing until the side clips
engage. Snap the Trim-plate into
the Radio Housing.
(Figure C)
3
Slide the housing brackets onto
the side of the radio housing until
the clips engage. Note: Brackets
are marked left and right.
(Figure A)
1
ISO RADIO PROVISION WITH POCKET
A
B
C
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-8219 KIT ASSEMBLY
4
FINAL ASSEMBLY
Make wiring connections using the EIA color code chart shown belowand the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
FINAL WIRING CONNECTIONS
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray/ Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
METRA / EIA WIRING CODE
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
1
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D

5
NOTES
99-8219

99-8219 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
REV.05/13/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-8219