Metso Neles GB Series Operating and maintenance manual

Control Valves
Globe-Balanced Single Seated,
Cage-Guide
Series GB
Installation, Maintenance and
Operating Instructions
4 GV 75 en • 4/2018

24 GV 75 en
READ THESE INSTRUCTIONS FIRST!
These instructions provide information about safe handling and operation of the valve.
If you require additional assistance, please contact the manufacturer or manufacturer's representative.
Addresses and phone numbers are printed on the back cover.
See also www.metso.com/valves for the latest documentation.
SAVE THESE INSTRUCTIONS!
Subject to change without notice.
All trademarks are property of their respective owners.
Table of Contents
1 GENERAL...............................................................3
1.1 Scope of the manual ............................................3
1.2 Valve construction ................................................3
1.3 Valve markings .......................................................3
1.4 Technical specifications ......................................3
1.5 Valve seat leakage class ......................................3
1.6 Recycling and disposal ........................................4
1.7 Safety precautions ..........................................4
2 TRANSPORTATION, RECEPTION AND
STORAGE...............................................................4
3 VALVE INSTALLATION .........................................4
3.1 General ......................................................................4
3.2 Installation into the pipeline .............................4
3.3 Control valve assembly .......................................5
3.4 Valve insulation......................................................5
4 MAINTENANCE ....................................................5
4.1 General ......................................................................5
4.2 Gland packing adjustment.................................5
4.3 Replacing the gland packing ..........................5
4.4 Replacing the trim and body reassembly ....6
4.5 Pilot Plug...................................................................7
5 TESTING THE VALVE ............................................7
6 REMOVAL & MOUNTING THE ACTUATOR ..........9
7 TOOLS .................................................................10
8 ORDERING SPARE PARTS ..................................10
9 EXPLODED VIEW AND PARTS LIST ...................11
10 DIMENSIONS AND WEIGHTS .............................12
10.1 Valve GB ................................................................. 12
10.2 Actuators VD, VC................................................. 14
11 TYPE CODE .........................................................18
This product meets the requirements set by the Customs Union of the Republic of Belarus,
the Republic of Kazakhstan and the Russian Federation.

4 GV 75 en 3
1 GENERAL
1.1 Scope of the manual
This manual provides essential information on series GB,
Globe-Balanced single seated, cage guide sliding stem
globe valves. Actuators and positioners are only discussed
briefly. Refer to the individual manuals for further informa-
tion on their installation, operation and maintenance.
1.2 Valve construction
Series GB, Globe-Balanced cage guide valves are flanged
(weld end available) single seated sliding stem control
valves. The valve seat ring and cage and plug with stem is a
module accessible through the bonnet opening (top entry)
of the body.
Our standard design provides a cage guide with a piston
type plug with a quick change seat ring. The two split cages
and inserted plug seal ring makes strong support to ensure
valve alignment.
This series is available with series of reduced Cv trims and
the standard seat tightness is class III~IV, optional trims can
meet to class V, ANSI/FCI 70-2.
The detailed structure is revealed by the type code shown
on the valve identification plate. The type code is explained
in Section 11.
1.3 Valve markings
The body markings are: manufacturer's trademark, nominal
size, pressure rating and material of the body. The valve has
an identification plate attached to it, see Fig. 2. .
Markings on the identification plate:
1. Type designation (Valve code)
2. Size, Rating
3. Cv
4. Body material
5. Plug, Stem material
6. Seat material
7. Temp. min./max.
8. Maximum (shut-off) pressure
9. Valve manufacturing date
10. Tag No.
11. Serial No.
1.4 Technical specifications
Face-to-face length: ANSI/ISA-75.08.01, 03, 04, 05 &
ANSI/ISA-75.08.06 (Long)
Body rating: Class 150 to Class 2500
PN 10 to PN 420
Max. pressure differential:
acc. to pressure class
Temperature range: -198° to +593 °C (depending on the
body materials and bonnet type)
Flow direction: indicated by an arrow on the body
Actuator mounting: threaded bonnet with yoke nut or
bolted yoke
Stem connection: clamp with bolts/nuts
Dimensions: see Section 10
Weights: see Section 10
Note that the max. shut-off pressure is based on the
mechanical maximum differential pressure at ambient tem-
perature. You must always observe the fluid temperature
when deciding on applicable pressure values. When select-
ing a valve you must also check the noise level, cavitation
intensity, flow velocity, actuator load factor, etc. using Nel-
prof.
1.5 Valve seat leakage class
The valve follows the seat leakage classifications of ANSI/
FCI 70-2 requirement.
NOTE:
Selection and use of the valve in a specific application
requires close consideration of detailed aspects. Due to
the nature of the product, this manual cannot cover all the
individual situations that may occur when the valve is
used.
If you are uncertain about use of the valve or its suitability
for your intended purpose, please contact Metso for more
information.
For valves in oxygen service, please see also the separate
installation, maintenance and operating instructions for
oxygen service (see Metso document id:10O270EN.pdf).
Fig. 1 Construction of a Neles Globe-Balanced Single
Seated, Cage Guide Valve
Fig. 2 Identification(name) plate example
TYPE
BODY
STEM
SEAT
PLUG
DATE
t max.
SIZE
M.A.W.P
TAG No.
0496
235 Cheomdansane op 1-ro, Daesowon-myeon,
Chungju-si, Chungc heongbuk-do, Korea
Metso Flow Control
FLUID GROUP
t min.
CO No.
RATING
Cv

44 GV 75 en
1.6 Recycling and disposal
Most valve parts can be recycled if sorted according to
material. Most parts have a material marking. A material list
is supplied with the valve. In addition, separate recycling
and disposal instructions are available from the manufac-
turer. A valve can also be returned to the manufacturer for
recycling and disposal for a fee.
1.7 Safety precautions
2 TRANSPORTATION, RECEPTION AND
STORAGE
Check the valve and the accompanying devices for any
damage that may have occurred during transport.
The valve is delivered in the closed position. A valve
equipped with a spring-return actuator is delivered in the
position determined by the spring.
Store the valve carefully before installation, preferably
indoors in a dry place.
3 VALVE INSTALLATION
3.1 General
Remove the flow port protectors and check that the valve is
clean inside.
3.2 Installation into the pipeline
3.2.1 Pipeline cleaning
Make sure no foreign particles, such as sand or pieces of
welding electrode, are in the pipeline, they may damage
the sealing surfaces.
CAUTION:
Do not exceed the valve performance limitations!
Exceeding the limitations marked on the valve may cause
damage and lead to uncontrolled pressure release.
Damage or personal injury may result
CAUTION:
Do not dismantle the valve or remove it from the pipe-
line while the valve is pressurised!
Dismantling or removing a pressurised valve will result in
uncontrolled pressure release. Always isolate the relevant
part of the pipeline, release the pressure from the valve
and remove the medium before dismantling the valve.
Be aware of the type of medium involved. Protect yourself
and the environment from any harmful or poisonous sub-
stances. Make sure that no medium can enter the pipeline
during valve maintenance.
Failure to do this may result in damage or personal injury.
CAUTION:
Beware of the plug movement!
Keep fingers, other parts of the body, tools and other
objects out of the open flow port. Leave no foreign objects
inside the pipeline. When the valve is actuated, the plug
functions as a cutting device. Close and detach the actuator
pressure supply pipeline for valve maintenance.
Failure to do this may result in damage or personal injury.
CAUTION:
Protect yourself from noise!
The valve may produce noise in the pipeline. The noise
level depends on the application. It can be measured or
calculated using the Metso Nelprof software. Observe the
relevant working environment regulations in terms of
noise emission.
CAUTION:
Beware of a very cold or hot valve!
The valve body may be very cold or very hot during use.
Protect yourself against cold injuries or burns.
CAUTION:
When handling the valve or the control valve assem-
bly, take its weight into account!
Never lift the valve or control valve assembly by the posi-
tioner, the limit switch or their piping. Place the lifting
ropes securely around the valve body (see Fig. 3).
Damage or personal injury may result from falling parts.
CAUTION:
Follow the proper procedures when handling and
servicing Oxygen valves.
Fig. 3 Lifting the valve
CAUTION:
When handling the valve or the control valve assem-
bly, take its weight into account!
NOTE:
Over 260 °C, a heat-insulation should be installed, how-
ever don't insulate the cryogenic nor extension bonnet
relative to personal safety.

4 GV 75 en 5
3.2.2 Installation valve
The valve has an arrow indicating the flow direction. Install
the valve in the pipeline so that the flow direction of the
valve corresponds to the flow direction marked on the pipe.
The mounting orientation of the valve should be vertical
position as it is shown on Fig.4.
Choose flange gaskets according to the operating
conditions.
Do not attempt to correct a pipeline misalignment by
means of flange bolting.
Loads on the valve body from pipeline vibrations can be
reduced by supporting the pipeline properly. Reduced
vibration also increases the lifetime of the positioner.
Where necessary, you can support the valve by the body, using
regular pipe clamps and supports. Do not fasten supports to
the valve or flange bolting or to the actuator, see Fig. 4.
3.3 Control valve assembly
Check all joints, piping and cables.
Check that the actuator stop screws, positioner and limit
switches are calibrated. Refer to their installation, mainte-
nance and operating manuals.
3.4 Valve insulation
If necessary, the valve may be insulated. Insulation must not
continue above the upper level of the valve body, see Fig-
ure 5.
4 MAINTENANCE
4.1 General
The Neles Globe-Balanced Single Seated valves require no
regular maintenance. However, check the gland packing for
leakage. This section outlines the maintenance that can be
carried out by the user.
The numbers in parentheses refer to the parts lists and the
exploded views of the valve in Section 9.
4.2 Gland packing adjustment
In the event of a packing leakage tighten the hexagon nuts
(18) in ¼ turn steps each until the leakage is stopped. Do
not tighten more than necessary.
4.3 Replacing the gland packing
Make sure the valve is not pressurised.
Remove the actuator from the valve stem according
to the instructions given in the actuator manual.
Loosen and remove the gland flange nuts (18).
Remove the gland flange (9b), and gland (9a) up to
the valve stem.
Remove the old packing rings (69) using a pointed
tool, avoid damaging the seal surfaces and valve
stem.
NOTE:
For any other mounting position, please consult the
factory.
Fig. 4 Installing the control valve into pipeline using
supports
Fig. 5 Insulation of the valve
Insulation limit
CAUTION:
Observe the safety precautions listed in Section 1.7
before starting work!
CAUTION:
When handling the valve or the control valve assem-
bly, take its weight into account!
NOTE:
If you send the valve to the manufacturer for repair, do not
dismantle it. Clean the valve carefully, including the inside.
For safety reasons, inform the manufacturer of the nature
of the medium when you send the valve.
NOTE:
Always use original spare parts to make sure the valve
functions as intended.
CAUTION:
Do not dismantle the valve or remove it from the pipe-
line while the valve is pressurised!
Fig. 6 Gland packing

64 GV 75 en
Clean the packing ring counterbore.
Mount the new packing rings one by one into the
packing gland box using the gland as a tool and
mount the gland with hand-tightened nuts.
Fasten the gland with the nuts (18) and tighten
them.
Check leakage when the valve is pressurised.
4.4 Replacing the trim and body
reassembly
Make sure the valve is not pressurised.
Remove the actuator from the valve stem according
to the instructions given in the actuator manual and
Section 6.
Loosen the gland nuts (18) slightly.
Remove the hexagon nuts (17).
Remove the bonnet (8)
Remove the stem and plug (5 & 3) with the cage (15).
Remove the cage (15), cage guide (16) and the seal ring
(64). Avoid from damaging the seal ring between the
cage and cage guide.
Remove the body gasket (65), seat ring (7), seat gas-
ket (63)
Remove the hexagon nuts (18), gland flange (9b)
and packing gland (9a).
Fig. 7 Tightening sequence of the bonnet nuts
Table 1 Required torques for bonnet nuts
Valve Size Rating
(ANSI) Bonnet Stud Bolts Required Torques
(±5% allowable)
mm in Size Q'ty Nm lbf ft
50 2
150-300 1/2"-13UNC 8 45 33
600 9/16"-12UNC 8 65 48
900 7/8"-9UNC 8 140 103
1500 7/8"-9UNC 8 140 103
2500 7/8"-9UNC 8 140 103
75 3
150-300 5/8"-11UNC 8 90 66
600 5/8"-11UNC 10 90 66
900 7/8"-9UNC 8 250 184
1500 1-1/8"-8UN 8 300 221
2500 1-1/4"-8UN 8 400 295
100 4
150-300 3/4"-10UNC 8 160 118
600 3/4"-10UNC 10 160 118
900 1-1/8"-8UN 8 560 413
1500 1-1/8"-8UN 8 560 413
2500 1-1/2"-8UN 8 1400 1033
150 6
150-300 3/4"-10UNC 12 160 118
600 7/8"-9UNC 12 250 184
900 1-1/8"-8UN 12 560 413
1500 1-3/8"-8UN 12 800 590
2500 1-1/2"-8UN 12 1400 1033
200 8
150-300 7/8"-9UNC 12 250 184
600 1"-8UNC 12 380 280
900 1-3/8"-8UN 12 1100 811
1500 1-5/8"-8UNC 12 1200 885
250 10
150-300 1"-8UNC 16 380 280
600 1"-8UNC 16 380 280
900 1-3/8"-8UN 12 1100 811
1500 1-3/4"-8UN 12 1200 885
300 12
150-300 1-1/8"-8UN 16 560 413
600 1-1/8"-8UN 16 560 413
900 1-3/8"-8UN 20 1100 811
2500 2-3/4"-8UNC 12 3500 2581
350 14
150-300 1-1/4"-8UN 16 790 583
600 1-1/4"-8UN 16 790 583
900 1-1/2"-8UN 20 1400 1033
400 16
150-300 1-1/4"-8UN 20 790 583
600 1-3/8"-8UN 20 1100 811
900 1-5/8"-8UNC 20 1200 885
1500 2-1/2"-8UNC 12 3000 2213
Table 2 Required torques for bonnet nuts
Packing
Type
Stem Size Rating
(ANSI)
Required Torques
mm Min. Nm(lbf ft) Max. Nm(lbf ft)
Graphite
&PTFE
Carbon Fiber
packing
Ø12.7
150-300 5 (4) 7 (5)
600 6 (4) 8 (6)
900 7 (5) 10 (7)
1500 9 (7) 12 (9)
2500 10 (7) 14 (10)
Ø19.05
150-300 11 (8) 16 (12)
600 14 (10) 19 (14)
900 17 (12) 23 (17)
1500 19 (14) 27 (20)
2500 22 (16) 21 (15)
Ø25.4
150-300 18 (13) 25 (18)
600 23 (17) 32 (24)
900 27 (20) 38 (28)
1500 32 (24) 44 (32)
2500 36 (27) 51 (38)
Ø36
150-300 26 (19) 36 (27)
600 32 (24) 45 (33)
900 39 (29) 54 (40)
1500 45 (33) 64 (47)
2500 52 (38) 73 (54)
V-ring
packing
(PTFE)
Ø12.7
150-300 3 (2) 5 (4)
600 4 (3) 6 (4)
900 5 (4) 7 (5)
1500 6 (4) 8 (5)
2500 7 (5) 10 (7)
Ø19.05
150-300 8 (6) 11 (8)
600 10 (7) 14 (10)
900 12 (9) 16 (12)
1500 14 (10) 19 (14)
2500 16 (12) 22 (16)
Ø25.4
150-300 13 (10) 18 (13)
600 16 (12) 22 (16)
900 19 (14) 27 (20)
1500 22 (16) 31 (23)
2500 25 (18) 35 (26)
Ø36
150-300 18 (13) 25 (18)
600 23 (17) 32 (24)
900 27 (20) 38 (28)
1500 32 (24) 44 (32)
2500 36 (27) 51 (38)
NOTE:
The trim set consists of the seat, plug and stem, cage, cage
guide, seal ring and gaskets (for seat and body).
CAUTION:
Do not reuse the spiral wound gaskets (63 & 65), this is
need to be replace each time the valve is disassem-
bled.

4 GV 75 en 7
Remove the old packing rings (69).
Clean the body gasket surface.
Insert a new seat gasket (63) and the seat ring (7)
into the body.
Install the cage (15), seal ring (64), cage guide (16)
and plug stem assembly (3, 5, 6) very carefully.
Insert the body gasket (65).
Mount the bonnet on the body carefully maintaining
alignment with the plug and the stem and with the
cage in the closed position, so that the arrow on the
body and on the bonnet point in the same direction.
Insert the hexagon nuts (17) into studs (13) and
slightly the nuts.
Insert the packing (69) according to above 4.3
Tighten hexagon nuts (17) until plug and seat con-
tact is obtained with proper bolt torque.
Adjust and tighten the gland nuts finally.
4.5 Pilot Plug
Disassembly & Assembly
Mount the plug and stem assembly on the chuck to
setting. Compress the stem by the lathe center for
release (reduce) the spring tension.
Remove the pilot wire (76).
Remove the pilot bolts (75)
Remove the pilot cover (74)
Remove the pilot plug (73) and stem (5) from pilot
main plug (71).
Remove the pilot spring (77) carefully.
Inspect the pilot plug (73) and the pilot seat as well
as the surface inside of the pilot main plug (71). If
there is damage, scratches or grooves, it should be
replaced or repaired.
Insert the cleaned pilot spring (77) into the upper
side of main plug.
Install the pilot plug (73) & stem (5) on the spring
(77).
Install the pilot cover (74) and fasten the pilot bolts
(75) keep in balance.
Install wire (76) for connecting the all pilot bolts due
to prevent loose on operation.
5 TESTING THE VALVE
We recommend that the valve body is pressure-tested after
the valve has been assembled.
The pressure test should be carried out in accordance with
an applicable standard for the pressure rating. The valve
must be in the open position during the test.
NOTE:
If the valve have excess leakage, the plug and seating sur-
face need lapping and cleaning.
CAUTION:
Do not excessively tighten stud nuts at this time.
CAUTION:
The all related parts (seat ring, cages, plug & stem,
bonnet) must be properly aligned in the body.
Fig. 8 Conventional Cage-Balance Trim
CAUTION:
Make sure to balance when loose the pilot bolts, and
be careful the spring tension to bounced off the pilot
plug and stem.
CAUTION:
Pressure testing should be carried out using equip-
ment conforming to the correct pressure class!
Fig. 9 Pilot Cage-Balance Trim

84 GV 75 en
Fig. 10 Different trim designs
Quick change, standard cage trim Tendril Multi-hole trim
Trim Design applications
Pilot balanced trim

4 GV 75 en 9
6 REMOVAL & MOUNTING THE
ACTUATOR
The actuator is attached to the valve according to the manual
for actuator with body assembly and plug stem adjustment .
Several types of Metso actuators can be used with suitable
clamps. Refer to the model VD spring-diaphragm and VC
double acting cylinder actuator manuals for further informa-
tion on their installation, maintenance and operation.
A. Actuator removal for Reverse
<air to open, stem retract> actuator (Fig. 12)
Lift up to the valve plug more than 20 % from the
seat ring, using by specified air pressure.
Loosen the stem lock nut (5**) and socket head
screws (1a**) and hexagon nuts (1b**).
Remove the clamp (1**).
Shut off and disconnect air supply line.
Support actuator with the suitable lifting device.
Remove the yoke nut (3**).
Remove the actuator from the valve body assembly.
B. Actuator removal for Direct <air to close, stem
extend> actuator (Fig. 12)
Shut off and disconnect the air supply lines and
accessories.
Loosen stem lock nut (5**) and socket head screws
(1a**) and hexagon nuts (1b**).
Remove the clamp (1**).
Support actuator with the suitable lifting device.
Remove the yoke nut (3**).
Remove the actuator from the valve body assembly.
Standard valve construction
With the handwheel or pneumatically, push the
valve stem and plug to be slightly touched with seat
ring to make sure if valve is fully closed.
With the handwheel or pneumatically, stroke the
actuator to the fully open.
Measure the maximum distance between the valve
stem and actuator top stem.
CAUTION:
Beware of the plug movement!
Do not use air pressure higher than what specified on the
identification plate.
Fig. 11 Measurement of Gap 2
Fig. 12 VD Actuator
V-A (Valve-Actuator) Mounting Part (**)
1** CLAMP 1a**SOCKET HEAD SCREW
1b** HEXAGON NUT 3**YOKE NUT (see above VD g.)
5** STEM LOCK NUT 6** LOCK WASHER
VD Actuator part
1. YOKE 10. LOWER CASE 18 TOP STEM 20. UPPER CASE
21. LIFTING EYE NUT 22. WASHER 23. HEXAGON SCREW 24. HEXAGON SCREW
25. HEXAGON NUT 30. IDENTIFICATION PLATE 32. INDICATOR 32a. ROUND HEAD SCRREW
34. VENT CAP 99. AIR SUPPLY PORT
Direct Action actuator
(Air to Close, stem extend)
Reverse Action actuator
(Air to Open, stem retract)

10 4 GV 75 en
Calculate the gap (measured value – rated travel =
gap 1)
Move down the top stem so that the distance
between the valve stem and actuator top stem
should be gap 1
Fit the clamp to align with both stems thread
Line up the stroke indicator with the clamp indicator
arrow and check actuator for operation.
Tighten the socket head screws after adjusted the
rated stroke.
Pilot valve construction
With the handwheel or pneumatically, push the
valve stem and plug to be slightly touched with seat
ring to make sure if valve is fully closed. And mark
the valve stem end location by a line on the yoke or
travel indicator.
And move up the top stem. And mark the valve stem
end location by a line on the yoke or travel indicator
after valve stem is moved by a spring inside pilot
plug.
Measure the distance between two lines, which is
gap 2.
Stroke the actuator to the fully open.
Measure the maximum distance between the valve
stem and actuator top stem.
Calculate the gap (measured value – rated travel –
gap 2 = gap 3)
Move down the top stem so that the distance
between the valve stem and actuator top stem
should be gap 2
Fit the clamp to align with both stems thread
Close the valve fully.
Line up the stroke indicator with the clamp indicator
arrow and check actuator for operation.
Tighten the socket head screws after adjusted the
rated stroke.
C. Actuator replacement (mounting)
Mount the new or repaired actuator on top of the
bonnet, using a suitable lifting device.
Insert the yoke nut and tightly fasten the yoke by
turning the yoke nut clockwise using tightening tools.
Connect air line and accessories.
Tighten stem socket head screws (1a**) and hexa-
gon nuts (1b**) with stem lock nut (5**).
D. Type ‘VC’Springless Cylinder, Double Acting Actuator
This actuator is springless cylinder, double acting
actuator, can use the 3/8”, 1/2” NPT port according to
specified on the data sheet for all air lines.
Refer to the model VC double acting cylinder actua-
tor manuals for further information on their installa-
tion, maintenance and operation. .
7TOOLS
Removal of the actuator
L- wrench set (mm)
hex socket wrench set
chisel and hammer (10 pound)
+,- drivers
8 ORDERING SPARE PARTS
When ordering spare parts, always include the following
information:
type code, sales order number, serial number
number of the parts list, part number, name of the
part and quantity required
This information can be found from the identification plate
or documents.
CAUTION:
Avoid to turn the valve plug and stem when plug is on
seat ring to prevent the seating line from being dam-
aged.
NOTE:
Always use original spare parts to make sure that the valve
functions as intended.

4 GV 75 en 11
9 EXPLODED VIEW AND PARTS LIST
•) Delivered as a set
**) V-A Mounting Parts
Item Description Recommended spare part
1BODY
2*PLUG SET
3*PLUG
5*STEM
6*PLUG PIN
3** YOKE NUT
7 SEAT RING
8 BONNET
9a GLAND
9b GLAND FLANGE
12 DISK SPRING ASS'Y
13 STUD
14 STUD
15 CAGE
16 CAGE GUIDE
17 HEXAGON NUT
18 HEXAGON NUT
19 IDNTIFICATION PLATE
19A RIVET
21 LANTERN RING
25 DISK STACK
63 SEAT GASKET X
64 SEAL RING X
65 BODY GASKET X
67 PACKING SPACER
69 PACKING RING X
71 PILOT MAIN PLUG
73 PILOT PLUG
74 PILOT COVER
75 PILOT BOLT
76 PILOT WIRE
77 PILOT SPRING (Located inside the pilot main plug, see Fig. 8 at page 7)
1
8
17
9b
18
13
14
11
63
7
15
64
16
3
6
5
65
21
69
67
67
22
69
9a
69
9a
**
72
71
76
74
73
PILOT PLUG
75
77

12 4 GV 75 en
10 DIMENSIONS AND WEIGHTS
10.1 Valve GB
150 # / 300 # / 600 #
Dimension
(mm)
Size
(mm)
ABCDEF G H
Weight (kg)
(Approximate)
150# 300# 600# 150# 300# 600# STD EXT COMMON 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600#
50 254 267 286 83 83 83 178 295 110 150 165 165 19.1 19.1 19.1 120.7 127 127 4 8 8 30 32 40
80 298 318 337 109 109 120 222 330 115 190 210 210 19.1 22.2 22.2 152.4 168.3 168.3 4 8 8 65 67 72
100 352 368 394 135 135 135 248 380 140 230 255 275 19.1 22.2 25.4 190.5 200 215.9 8 8 8 100 103 112
150 451 473 508 170 170 178 340 430 150 280 320 355 22.2 22.2 28.6 241.3 269.9 292.1 8 12 12 185 195 240
200 543 568 610 230 230 230 451 490 150 345 380 420 22.2 25.4 31.8 298.5 330.2 349.2 8 12 12 363 385 443
250 673 708 752 275 275 275 488 600 150 405 445 510 25.4 28.6 34.9 362 387.4 431.8 12 16 16 552 595 681
300 737 775 819 350 350 350 543 660 150 485 520 560 25.4 31.8 34.9 431.8 450.8 489 12 16 20 905 955 1020
350 889 927 972 385 385 385 616 740 210 535 585 605 28.6 31.8 38.1 476.3 514.4 527 12 20 20 1170 1230 1311
400 1016 1057 1108 440 440 440 692 820 220 595 650 685 28.6 34.9 41.3 539.8 571.5 603.2 16 20 20 1380 1460 1587
Dimension
(inch)
Size
(inch)
ABCDEFGH
Weight (lbs)
(Approximate)
150# 300# 600# 150# 300# 600# STD EXT COMMON 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600# 150# 300# 600#
2" 1010.511.33.33.33.3713.114.3 5.96.56.50.80.80.84.855488667188
3" 11.7 12.5 13.3 4.3 4.3 4.7 8.7 15.55 4.5 7.5 8.3 8.3 0.8 0.9 0.9 6 6.6 6.6 4 8 8 143 148 159
4" 13.9 14.5 15.5 5.3 5.3 5.3 9.8 15.82 5.5 9.1 10 10.8 0.8 0.9 1 7.5 7.9 8.5 8 8 8 221 227 247
6" 17.8 18.6 20 6.7 6.7 7 13.4 18.38 5.9 11 12.6 14 0.9 0.9 1.1 9.5 10.6 11.5 8 12 12 408 430 529
8" 21.4 22.4 24 9.1 9.1 9.1 17.8 21.92 5.9 13.6 15 16.5 0.9 1 1.3 11.8 13 13.7 8 12 12 800 849 977
10" 26.5 27.9 29.6 10.8 10.8 10.8 19.2 26.37 5.9 15.9 17.5 20.1 1 1.1 1.4 14.3 15.3 17 12 16 16 1217 1312 1501
12" 29 30.5 32.2 13.8 13.8 13.8 21.4 28.18 5.9 19.1 20.5 22 1 1.3 1.4 17 17.7 19.3 12 16 20 1995 2105 2249
14" 35 36.5 38.3 15.2 15.2 15.2 24.3 33.30 8.3 21.1 23 23.8 1.1 1.3 1.5 18.8 20.3 20.7 12 20 20 2579 2712 2890
16" 40 41.6 43.6 17.3 17.3 17.3 27.2 35.78 8.7 23.4 25.6 27 1.1 1.4 1.6 21.3 22.5 23.7 16 20 20 3042 3219 3499
DRILLING
No of Hole. = H
Dia. Of Hole = F
Pitch Circle Dia. = G
BC
EXTENSION BONNET
neles
A
D
ØE
c
MATERIAL
HEAT NO.
SIZE-RATING
DRILLING
Dia. of Hole = F
Pitch Circle Dia = G
No of Hole = H
EXTENSION / CRYOGENIC

4 GV 75 en 13
900 # / 1500 #
Dimension
(mm)
Size
(mm)
ABCDEF GH
Weight (kg)
(Approximate)
900# 1500# 900# 1500# STD EXT COMMON 900# 1500# 900# 1500# 900# 1500# 900# 1500# 900# 1500#
40 333 333 90 90 278 380 110 180 180 28.6 28.6 123.8 123.8 4 4 105 115
50 375 375 113 113 300 400 110 215 215 25.4 25.4 165.1 165.1 8 8 130 140
80 441 460 142 142 330 430 115 240 265 25.4 31.8 190.5 203.2 8 8 207 220
100 511 530 182 182 350 450 150 290 310 31.8 34.9 235 241.3 8 8 397 475
150 714 768 210 210 393 500 150 380 395 31.8 38.1 317.5 317.5 12 12 530 540
200 914 972 290 290 480 600 150 470 485 38.1 44.5 393.7 393.7 12 12 698 821
250 991 1067 310 310 518 650 150 545 585 38.1 50.8 469.9 482.6 16 12 955 1137
300 1130 1219 385 385 680 800 150 610 675 38.1 54 533.4 571.5 20 16 1180 1240
350 1257 1257 420 420 770 920 210 640 750 41.3 60.3 558.8 635 20 16 1387 1477
400 1422 1422 450 470 850 1050 220 705 825 44.5 66.7 616 704.8 20 16 1601 1721
Dimension
(inch)
Size
(inch)
ABCDE F G H
Weight (lbs)
(Approximate)
900# 1500# 900# 1500# STD EXT COMMON 900# 1500# 900# 1500# 900# 1500# 900# 1500# 900# 1500#
1" 11.511.53.23.2913 4 5.97.1114444132132
1-1/2" 13.1 13.1 3.5 3.5 10 15 4 7.1 7.1 1.1 1.1 4.9 4.9 4 4 139 139
2" 14.8 14.8 4.4 4.4 12 15 4 8.5 8.5 1 1 6.5 6.5 8 8 148 148
3" 17.4 18.1 5.6 5.6 13 17 5 9.4 10.4 1 1.3 7.5 8 8 8 331 359
4" 20.1 20.9 7.2 7.2 15 19 6 11.4 12.2 1.3 1.4 9.3 9.5 8 8 538 562
6" 28.1 30.2 8.3 9.4 17 20 6 15 15.6 1.3 1.5 12.5 12.5 12 12 1168 1191
8" 36 38.3 11.4 11.4 22 24 6 18.5 19.1 1.5 1.8 15.5 15.5 12 12 1539 1810
10" 39 42 12.2 13.8 24 28 6 21.5 23 1.5 2 18.5 19 16 12 2105 2507
12" 44.5 48 15.2 15.2 27 31 6 24 26.6 1.5 2.1 21 22.5 20 16 2602 2734
14" 49.5 49.5 15.2 15.2 30 36 8 25.2 29.5 1.6 2.4 22 25 20 16 3058 3256
16" 56 56 17.7 17.7 33 41 8 27.8 32.5 1.8 2.6 24.3 27.7 20 16 3530 3794

14 4 GV 75 en
10.2 Actuators VD, VC
Dimension
(mm)
Size
(mm)
Without handwheel With handwheel
A2 Bd / Bhd Br / Bhr Weight
(kg) A2 A3 Bdh Brh Weight (kg)
VD_25 E 255 348 373 12 255 312 110 170 23
VD_25 D 255 373 395 17
VD_29 E 295 391 416 18 295 312 122 182 29
VD_29 D 295 431 453 26
VD_37 E 375 464 489 28 375 352 131 211 43
VD_37 D 375 514 535 46
Dimension
(inch)
Size
(inch)
Without handwheel With handwheel
A2 Bd / Bhd Br / Bhr Weight
(lbs) A2 A3 Bdh Brh Weight (lbs)
VD_25E101415261012 4 7 51
VD_25D10151637
VD_29E121516401212 5 7 64
VD_29D12171857
VD_37E151819621514 5 8 95
VD_37 D 15 20 21 101
Standard spring High spring Standard spring
VDD/R E VDD/R D Side handwheel(25/29/37)
VDRVDD

4 GV 75 en 15
NOTE
1. "E" refers to Spring range 0.8~2.6
2. "D" refers to Spring range 1.5~3.4
3. "Br / Bhr" refers to reverse acting actuator, VDR E / D
4. "Bd / Bhd" refers to direct acting actuator, VDD E / D
5. "Cdh / Crh" Top side handwheel actuator, VD_48/55
Dimension
(mm)
Size
(mm)
Without handwheel With handwheel
A2 Bd / Bhd Br / Bhr Weight
(kg) Bdh Brh Cdh Crh Weight
(kg)
VD_48 E 486 652 677 86 896 865 1102 1072 112
VD_48 D 486 702 724 118 946 915 1152 1122 144
VD_55 E 566 695 720 112 940 910 1145 1115 145
VD_55 D 566 745 767 152 990 960 1195 1165 185
Dimension
(inch)
Size
(inch)
Without handwheel With handwheel
A2 Bd / Bhd Br / Bhr Weight
(lbs) Bdh Brh Cdh Crh Weight
(lbs)
VD_48 E 19 26 27 190 35 34 43 42 247
VD_48 D 19 28 29 260 37 36 45 44 317
VD_55 E 22 27 28 247 37 36 45 44 320
VD_55 D 22 29 30 335 39 38 47 46 408
Top side handwheel(VDD48/55) Top side handwheel(VDR48/55)
Bdh
Brh
Cdh
Crh

16 4 GV 75 en
VC actuators without handwheel
VC actuators without handwheel
VC, without volume chamber VC, with volume chamber
B
A
B1
B2
ØC
ØC
Stroke
(mm)
#30 #40 #50
ØC 370 ØC 460 ØC 560
B1 Weight (kg) B1 Weight (kg) B1 Weight (kg)
B2 A B B2 A B B2 A B
40 640 92 115 810 120 148 810 186 234
760 935 935
50 650 94 118 820 123 152 820 189 237
790 965 965
60 660 97 121 830 126 155 830 192 242
820 995 995
70 670 100 124 840 128 159 840 195 246
850 1025 1025
80 680 103 127 850 131 162 850 198 251
880 1055 1055
90 690 106 130 860 134 166 860 201 256
910 1085 1085
100 700 108 133 870 137 173 870 203 261
940 1115 1115
120 720 114 139 890 142 177 890 209 270
1000 1175 1175
140 910 148 184 910 215 279
1235 1235
180 950 159 198 950 227 298
1355 1355
Stroke
(mm)
#60 #70 #80
ØC 660 ØC 710 ØC 820
B1 Weight(kg) B1 Weight(kg) B1 Weight(kg)
B2ABB2ABB2AB
100 954 255 344 955 322 438 954 378 519
1199 1203 1207
120 974 262 355 975 330 450 974 386 531
1259 1263 1267
140 994 269 365 995 338 461 994 394 543
1319 1323 1327
180 1034 283 386 1035 354 484 1034 410 567
1439 1443 1447
240 1094 303 417 1095 377 518 1094 435 604
1619 1623 1627
280 1134 451 628
1747
Stroke
(mm)
#30 #40 #50
ØC 15 ØC 18 ØC 22
B1 Weight(lbs) B1 Weight(lbs) B1 Weight(lbs)
B2 A B B2 A B B2 A B
40 25 203 254 32 265 326 32 410 516
30 37 37
50 26 207 260 32 271 335 32 417 522
31 38 38
60 26 214 267 33 278 342 33 423 534
32 39 39
70 26 220 273 33 282 351 33 430 542
33 40 40
80 27 227 280 33 289 357 33 437 553
35 42 42
90 27 234 287 34 295 366 34 443 564
36 43 43
100 28 238 293 34 302 381 34 448 575
37 44 44
120 28 251 306 35 313 390 35 461 595
39 46 46
140 36 326 406 36 474 615
49 49
180 37 351 437 37 500 657
53 53
Stroke
(mm)
#60 #70 #80
ØC 26 ØC 28 ØC 32
B1 Weight(lbs) B1 Weight(lbs) B1 Weight(lbs)
B2 A B B2 A B B2 A B
100 38 562 758 38 710 966 37 833 1144
47 47 48
120 38 578 783 38 728 992 38 851 1171
50 50 50
140 39 593 805 39 745 1016 39 869 1197
52 52 52
180 41 624 851 41 780 1067 41 904 1250
57 57 57
240 43 668 919 43 831 1142 43 959 1332
64 64 64
280 45 994 1385
69

4 GV 75 en 17
VC actuators with handwheel
VC actuators with handwheel
& volume chamber
VC, with optional handwheel VC, with optional handwheel
B
A
B2
ØC
ØC
B1
Stroke
(mm)
#30 #40 #50
ØC 370 ØC 460 ØC 560
B1 Weight (kg) B1 Weight (kg) B1 Weight (kg)
B2 A B B2 A B B2 A B
40 930 134 157 1095 180 208 1095 246 294
1055 1220 1220
50 940 137 160 1105 183 212 1105 249 299
1085 1250 1250
60 950 139 163 1115 186 215 1115 252 303
1115 1280 1280
70 960 142 167 1125 188 219 1125 255 308
1145 1310 1310
80 970 144 170 1135 191 222 1135 258 313
1175 1340 1340
90 980 147 173 1145 194 226 1145 261 318
1205 1370 1370
100 990 150 176 1155 197 230 1155 263 322
1235 1400 1400
120 1010 155 183 1175 202 237 1175 269 332
1295 1460 1460
140 1195 208 244 1195 275 341
1520 1520
180 1235 219 258 1235 287 360
1640 1640
Stroke
(mm)
#60 #70 #80
ØC 660 ØC 710 ØC 820
B1 Weight (kg) B1 Weight (kg) B1 Weight (kg)
B2ABB2ABB2AB
100 1239 315 404 1240 368 502 1289 438 579
1484 1488 1542
120 1259 322 415 1260 376 514 1309 446 591
1544 1548 1602
140 1279 329 425 1280 384 525 1329 454 603
1604 1608 1662
180 1319 343 446 1320 400 548 1369 470 627
1724 1728 1782
240 1379 363 477 1380 423 582 1429 495 664
1904 1908 1962
280 1469 511 688
2082
Stroke
(mm)
#30 #40 #50
ØC 15 ØC 18 ØC 22
B1 Weight (lbs) B1 Weight (lbs) B1 Weight (lbs)
B2 A B B2 A B B2 A B
40 37 295 346 43 397 459 43 542 648
42 48 48
50 37 302 353 44 403 467 44 549 659
43 49 49
60 37 306 359 44 410 474 44 556 668
44 50 50
70 38 313 368 44 414 483 44 562 679
45 52 52
80 38 317 375 45 421 489 45 569 690
46 53 53
90 39 324 381 45 428 498 45 575 701
47 54 54
100 39 331 388 45 434 507 45 580 710
49 55 55
120 40 342 403 46 445 522 46 593 732
51 57 57
140 47 459 538 47 606 752
60 60
180 49 483 569 49 633 794
65 65
Stroke
(mm)
#60 #70 #80
ØC 26 ØC 28 ØC 32
B1 Weight (lbs) B1 Weight (lbs) B1 Weight (lbs)
B2 A B B2 A B B2 A B
100 49 694 891 49 811 1107 51 966 1276
58 58 61
120 50 710 915 50 829 1133 52 983 1303
61 61 63
140 50 725 937 50 847 1157 52 1001 1329
63 63 65
180 52 756 983 52 882 1208 54 1036 1382
68 68 70
240 54 800 1052 54 933 1283 56 1091 1464
75 75 77
280 58 1127 1517
82

18 4 GV 75 en
11 TYPE CODE
VALVE CONSTRUCTIONS
- K: available for DN50-DN150 - M: available for DN25-DN150
- Bonnet material is equivalent to Body material.
TRIM CONSTRUCTIONS
Globe Balanced, Cage Guided Type, Series GB
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
GB 03 C W A J2 B P1 X BC S1 R1 X S G G S A X A E FC
1. VALVE SERIES
GB Globe Balanced, Cage guided type
2. BODY SIZE
02 2" / DN 50 03 3" / DN 80
04 4" / DN 100 06 6" / DN 150
08 8"/ DN 200 10 10" / DN 250
12 12" / DN 300 14 14" / DN 350
16 16" / DN400
Optional body size
18 18" / DN 450 20 20" / DN500
24 24" / DN 600 YY Special
3. PRESSURE RATING
CASME class 150 DASME class 300
FASME class 600 KEN PN 16
MEN PN 40
Optional pressure rating
GASME class 900 HASME class 1500
IASME class 2500 YSpecial
4. END CONNECTION
WFlanged RF, ASME B16.5
CFlanged RF, EN 1092-1
VSocket welding, ASME B16.11
QButt welding, ASME B16.25
Optional end connection
ZRing joint flange, ASME B16.5
YSpecial
5. BONNET CONSTRUCTION
Bonnet type Actuator connection
AGeneral Applicable for VD_25/29/37
BGeneral Applicable for VD_48/55
CGeneral Applicable for VD_30
DGeneral Applicable for VD_40/50/60/70
Optional bonnet construction
EExtension Applicable for VD_25/29/37
FExtension Applicable for VD_48/55
GExtension Applicable for VD_30
HExtension Applicable for VD_40/50/60/70
PCryogenic Applicable for VD_25/29/37
QCryogenic Applicable for VD_48/55
RCryogenic Applicable for VD_30
SCryogenic Applicable for VD_40/50/60/70
YSpecial Special
6. BODY MATERIAL
J2 A216 gr. WCB S6 A351 gr. CF8M
Optional body material
S1 A351 gr. CF3M YY Special
7. MODEL CODE
BModel B
8. PLUG MATERIAL
Material Description
P1 CA15 General for carbon steel valve
T6 CF8M General for stainless steel valve
Optional plug material
S1 CF3M
YY Special Special materials
9. PLUG APPLICATION
XNot Applicable
ACobalt based alloy
YSpecial
10. STEM MATERIAL
Material Description
BC 630 SS + HCr General for carbon steel valve
TC 316 SS + HCr General for stainless steel valve
Optional stem material
FC 316L SS + HCr
YY Special Special materials
11. SEAT TYPE
S1 Single metal seat
T1 Single soft seat
YY Special
12. SEAT / CAGE MATERIAL
Seat Cage Cage guide
R1 CA15 CB7Cu-1 / 630 SS + HCr CB7Cu-1 + HCr
R6 CF8M CF8M / 316 SS + HCr CF8M + HCr
Optional seat / Cage material
R3 CF3M CF3M / 316L SS + HCr CF3M + HCr
YY Special Special Special
- CA15 / AISI 410 is general for carbon steel valve.
- CF8M / AISI 316 is general for stainless steel valve.
13. SEAT APPLICATION
XNot Applicable
ACobalt based alloy
Optional seat application
PInsert RTFE
RInsert RTFE + Cobalt based alloy
YSpecial

4 GV 75 en 19
OTHERS
* ASME valve face to face length according to ISA 75.08. EN valve face to face length
according to ASME CL300.
* The body, bonnet, trim materials are subject to change as equivalent depending
on detail design.
* See 'Neles Globe Typecode Instruction' for further options and explanations.
TRIM TYPE & RATED Cv
- Rated Cv is different by the trim type and characteristic. - Srk means valve stroke in mm.
14. PACKING / BELLOWS TYPE
SGeneral packing
ELow emission, Live loaded
Optional Packing / Bellows Type
CBellows Seal (304 SS, Formed)
YSpecial
15. PACKING MATERIAL
GPTFE + Carbon fiber
FGraphite
TPTFE V-Ring
Optional packing material
HHi-Graphite
YSpecial
16. SEALS RING MATERIAL
GPTFE + Graphite
TPTFE
YSpecial
17. GASKET MATERIAL
SS/W gasket type, 316 SS + Graphite for general
LS/W gasket type, 316 SS + PTFE
Optional gasket material
HS/W gasket type, 316 SS + Graphite for high temp.
YSpecial
18. STUD / NUT MATERIAL
AA193 gr. B7 / A194 gr. 2H
BA193 gr. B8 / A194 gr. 8
KA320 gr. B8M cl. 2 / A194 gr. 8M
Optional Stud / Nut Material
HA193 gr. B16 / A194 gr. 4
YSpecial
19. OPTIONS
XNot applicable
EAnti-erosion
LLub. & Isol. valve
WWater seal
YNot Applicable
20.
TRIM TYPE
21.
TRIM
CHARACTERISTIC
22. RATED Cv
Sign Sign Sign Description Body Size and Stroke
2" Srk. 3" Srk. 4" Srk. 6" Srk. 8" Srk. 10" Srk. 12" Srk. 14" Srk. 16" Srk.
AGeneral
plug type LLinear FC General / Full capacity 74 (40) 142 (50) 230 (50) 380 (60) 600 (70) 950 (80) 1270 (120) 1740 (140) 2215 (160)
PPilot balanced
plug type 1A General / 1-Step reduction 48 (40) 98 (50) 160 (50) 275 (60) 455 (70) 700 (80) 970 (120) 1300 (140) 1530 (160)
2A General /
2-Step reduction 26 (40) 56 (50) 86 (50) 150 (60) 254 (70) 398 (80) 550 (120) 776 (140) 940 (160)
3A General /
3-Step reduction 16 (40) 34 (50) 52 (50) 90 (60) 152 (70) 238 (80) 340 (120) 464 (140) 568 (160)
FT Tendril 1 /
Full capacity 52 (40) 102 (50) 160 (50) 290 (60) 460 (70) 630 (80) 980 (120) 1300 (140) 1580 (160)
1T Tendril 1 /
1-Step reduction 40 (40) 42 (50) 120 (50) 220 (60) 340 (70) 460 (80) 735 (120) 985 (140) 1145 (160)
2T Tendril 1 /
2-Step reduction 27 (40) 10 (50) 70 (50) 130 (60) 195 (70) 255 (80) 405 (120) 565 (140) 670 (160)
3T Tendril 1 /
3-Step reduction 10 (40) 21 (50) 46 (50) 75 (60) 105 (70) 140 (80) 240 (120) 310 (140) 410 (160)
FM Tendril 2 /
Full capacity 50 (40) 100 (50) 155 (50) 280 (60) 425 (70) 590 (80) 920 (120) 1240 (140) 1530 (160)
1M Tendril 2 /
1-Step reduction 35 (40) 74 (50) 115 (50) 215 (60) 330 (70) 450 (80) 720 (120) 970 (140) 1130 (160)
2M Tendril 2 /
2-Step reduction 23 (40) 33 (50) 65 (50) 12 (60) 190 (70) 240 (80) 380 (120) 550 (140) 640 (160)
3M Tendril 2 /
3-Step reduction 8(40) 18 (50) 38 (50) 67 (60) 100 (70) 130 (80) 220 (120) 290 (140) 390 (160)
EEqual % FC General /
Full capacity 71 (40) 138 (50) 210 (50) 340 (60) 560 (70) 830 (80) 1240 (120) 1650 (140) 2090 (160)
1A General /
1-Step reduction 50 (40) 110 (50) 160 (50) 270 (60) 450 (70) 655 (80) 960 (120) 1275 (140) 1680 (160)
2A General /
2-Step reduction 24 (40) 50 (50) 82 (50) 136 (60) 236 (70) 374 (80) 524 (120) 746 (140) 854 (160)
3A General /
3-Step reduction 14 (40) 32 (50) 50 (50) 82 (60) 142 (70) 224 (80) 314 (120) 446 (140) 512 (160)
FT Tendril 1 /
Full capacity 50 (40) 82 (50) 135 (50) 235 (60) 370 (70) 500 (80) 840 (120) 1110 (140) 1400 (160)
1T Tendril 1 /
1-Step reduction 35 (40) 58 (50) 95 (50) 170 (60) 265 (70) 370 (80) 600 (120) 785 (140) 1020 (160)
2T Tendril 1 /
2-Step reduction 20 (40) 35 (50) 58 (50) 100 (60) 170 (70) 225 (80) 355 (120) 480 (140) 600 (160)
3T Tendril 1 /
3-Step reduction 10 (40) 20 (50) 32 (50) 58 (60) 105 (70) 125 (80) 205 (120) 290 (140) 350 (160)
FM Tendril 2 /
Full capacity 47 (40) 74 (50) 130 (50) 230 (60) 330 (70) 470 (80) 770 (120) 1050 (140) 1320 (160)
1M Tendril 2 /
1-Step reduction 33 (40) 56 (50) 92 (50) 165 (60) 245 (70) 330 (80) 570 (120) 720 (140) 960 (160)
2M Tendril 2 /
2-Step reduction 19 (40) 33 (50) 52 (50) 95 (60) 145 (70) 190 (80) 330 (120) 430 (140) 550 (160)
3M Tendril 2 /
3-Step reduction 8(40) 16 (50) 25 (50) 52 (60) 80 (70) 110 (80) 190 (120) 270 (140) 295 (160)
YSpecial YSpecial YY Special Contact Metso for Cv details

South Korea, 235 Cheomdansaneop 1-ro, Daesowon-myeon, Chungju-si, Chungbuk-do, 27466, Korea Tel. [phone], Fax [phone]
Europe, Vanha Porvoontie 229, P.O. Box 304, FI-01301 Vantaa, Finland. Tel. [phone]. Fax [phone]
North America, 44 Bowditch Drive, P.O. Box 8044, Shrewsbury, M A 01545, USA. Tel. [phone]. Fax [phone]
South America, Av. Independéncia, 2500-Iporanga, 18087-101, Sorocaba-São Paulo, Brazil. Tel. [phone]. Fax [phone]
Asia Pacic, 238B Thomson Road, #17-01 Novena Square Tower B, Singapore 307685. Tel. [phone]. Fax [phone]
China, 11/F, China Youth Plaza, No.19 North Rd of East 3rd Ring Rd, Chaoyang District, Beijing 100020, China. Tel. [phone]. Fax [phone]
Middle East, Roundabout 8, Unit AB-07, P.O. Box 17175, Jebel Ali Freezone, Dubai, United Arab Emirates. Tel. [phone]. Fax [phone]
www.metso.com/valves
Metso Flow Control Inc.
20 4 GV 75 en