MGG DTC Pro-Trainer User manual

1
DTC Pro-Trainer
Remote Training and Beeper Collar System
Instruction Manual
Pease read the entire guide before use

2
Brief introduction for the Remote Transmitter
Mode Button: hold over 3 seconds to turn on/off the Remote Transmitter.
Press the button to choose the different modes. There are 5 modes as follows:
V
S
1 2
R
T
Vibration mode
Static mode
1-9 Intensity Level
Run mode
1-9 Different Tones
OR
Location mode
Channel 1 or 2
Tone mode
Low Battery
Indicator
Vis the Vibration mode for the Training Collar
Sis the Static mode for the Training Collar
8 is the intensity Level of Vibration or Static
R is the running mode for the Remote Beeper and also re-activates the Remote Beeper functions
after being disabled by the Location mode.
T is the Tone Mode and allows you to choose from 9 different Remote Beeper Sound options
L is the Location Mode and also disables the Remote Beeper Functions
3is showing the third option from the different tone sounds
Channel button: Choose the different channels for Training Collar or/and beeper collar
Transmitter button: confirm the operation and send the signal to the collars
Up/Down button: adjust intensity levels of stimulation and choose the different tone sounds
Charging Jack: connect to the charger
Brief introduction for the Waterproof Training Collar:
Corrects the dog behaviour by stimulations (vibration or shock).
On/Off button: Turns the Training Collar on/off. Also set to be ready to encode the transmitter and
Training Collar by holding the on/off button for 10 seconds
Receiver indicator Light: Indicates when turned on/off and also serves as low-battery indicator
and after charge full.
Antenna
Charging Jack
Indicator Light
Channel (Collar) selector
Up/Down Button
Transmitter Button
Mode Button

3
Brief introduction for Remote Beeper
Waterproof Remote Beeper: Beeps with a tone and frequency set by the user.
On/Off button: Turns the Remote Beeper on/off. Also set to be ready to encode the transmitter
and Remote Beeper by holding the on/off button for 10 seconds.
Receiver indicator Light: Indicates when turned on/off and also serves as low-battery indicator
and when fully charged.
Charging Jack with cover: For connecting the charger.
Charging your devices
Lift the rubber cover protecting the Charging Jack.
Plug the charging lead into the Charging Jack Socket.
Plug the charger into a standard wall outlet
Low battery and charging indications for Remote
Transmitter
Please charge when the Low Battery sign shows up
Charge for 3 hours
Low battery and charging indications for Training Collar and Remote Beeper
When the battery is low, the green light will flash once every second changing from flashing twice
every second.
When charging, the green light will change to red without flashing.
When fully charged, the red LED light will turn off.
On/Off Button
Indicator Light
Charging Jack Socket
Contact Points
Beeper Speaker
Charging Jack Socket
On/Off Button
Indicator Light
Training Collar
Remote Beeper

4
How to set the Training Collar to work with a Remote Transmitter
Press the On/Off button to turn on the Training Collar. The Green indicator light flashes twice per
second. Now the Training Collar is in Standby status.
Turn the Training Collar off and the Green LED light goes out.
Press and hold the ON/OFF button for 3 seconds and the Training Collar indicator light will come on
and stay for 10 seconds. You must encode the Remote Transmitter with the Training Collar within
these 10 seconds. Choose channel 1 or 2 by pressing the Mode button and then press the
Transmitter button Y to confirm. The confirmation must be done within those 10 seconds, otherwise
you have to turn it off and start again.
For a second Training Collar, just choose the other channel and repeat the above.
How to set the Remote Beeper to work with a Remote Transmitter
Press the ON/OFF button to turn on the Remote Beeper, the Green indicator light flashes twice per
second. Now the Remote Beeper is in the Standby status.
Turn the Remote Beeper off and the Green LED light goes out.
Press and hold the ON/OFF button for 3 seconds and the Beeper indicator light will come on and
stay on for 10 seconds. You can choose channel 1 or channel 2 by pressing the Mode button and
then press the Transmitter button Y to confirm. The confirmation must be done within those 10
seconds, otherwise you have to turn it off and start again.
For a second Remote Beeper, just choose the other channel and repeat the above.
Operation between Remote Transmitter and Training Collar
Before use, please make sure the Remote Transmitter has been encoded with Training Collar
as per the above instructions.
Fitting the Charging Cable
To the Collars

5
Turn on The training collar and the transmitter. Select the channel which you encoded the
collar with (1 or 2)
Press the Mode Button to choose Vor Smode as you require
For V Mode –vibration mode –there are 9 intensity levels. Please use Up/Down button to adjust
them.
For S Mode –Static Mode –there are 9 intensity levels. Please use Up/Down button to adjust
them.
Press Transmitter button Yto send the signal to the collar receiver.
Operation between Remote transmitter and the Remote Beeper
Before use, please make sure you have encoded the Remote Transmitter with the Remote
Beeper and also choose the right channel.
Turn on/off the Remote Transmitter and the Training Collar (please refer to brief introduction on
‘How to set the Remote Beeper to work with a Remote Transmitter’).
Press the Mode Button to choose R, T or Lmode as you need and then press Transmitter button to
send the confirmation signal to the Remote Beeper.
For R Mode: There are 3 Running Modes. You have three choices of how often the beeper
sounds off when your dog is moving.
Silence Mode: The Beeper will keep Silent when the dog moves and when it stops it will beep
every 2 seconds.
5 Second Mode: The Beeper will beep every 5 seconds when the dog moves and when it stops it
will beep every 2 seconds.
10 Second Mode: The Beeper will beep every 10 seconds when the dog moves and when it stops
it will beep every 2 seconds.
For L Mode: The Location Mode will disable the Remote Beeper Functions. In this Mode you can
press the Transmitter Button to send a signal to the Remote Beeper and the Remote Beeper will
play a sound to help you locate your dog.
For T Mode: The Tone Mode can adjust to 9 different Tone sounds.
You can alter the Remote Beeper to different tone sounds any time you like. Please press Mode
button to change to the Tone Mode. Use the Up/Down button to change to your preferred tone
sound. Once decided, press Transmitter button Y to send the confirmation signal to the Remote
Beeper.

6
The Remote Beeper will play your selected sound
Mode
Tone
1
1 Beep
2
Whistle
3
Bird
4
3 Beeps
5
Cricket
6
Starling
7
Hawk
8
Hawk
9
Eagle
Frequency: 433.825MHz
Remote Transmitter: 7.4V 400mAh LiP
Training Collar: 3.7V 230mAh LiP
Remote Beeper: 3.7V 230mAh LiP
The Green Remote Beeper is worn on the collar on the topside of your dog’s neck and the
Orange Training Collar on the underside. It is at the correct tightness when you can slip one
finger between the collar and the dog.
Website: mggproducts.co.nz Email: inf[email protected]
© Machines Gadgets and Gizmows Ltd 2013