Micromax X249 User manual

X249 L2 Service Manual
1. Technical Specifications
Below given remarks are for reference only.
Particular
Remarks
Key Matrix For Flashing
N/A
Chipset
MT6260D
Android Version
N/A
Frequency
360Mhz
Network Mode
GSM 900/1800
ROM
24Mb
RAM
32Mb
Internal SD Card memory
NO
Expandable Memory
32GB
Factory mode code
*#510838#
2. CAUTIONS
I. Flashing & Servicing must be undertaken by qualified personnel only.
II. Ensure all work is carried out at an anti-static workstation and that an anti-static wrist strap is worn.
III. Use only approved Tools & components as specified in the parts list.
IV. Ensure all components, modules, screws, and insulators are correctly re-fitted after servicing and
alignment
V. Ensure all cables and wires are repositioned correctly if Handset disassembled
VI. Electrostatic discharge can easily damage the sensitive components of electronic products.
Therefore, Service Centre must adhere the precautions which mentioned above.
All manuals and user guides at all-guides.com
all-guides.com

X249 L2 Service Manual
3. L2 Level trouble shooting
3.1 Structural Parts Fault
3.2 Fail to Start Up
3.3 No Ringtone
3.4 LCD Abnormal Display
3.5 Charging Abnormal
3.6 Fail to Identify SIM
3.7 No Echo, Fail to Record (But There Has Ring Tone)
3.8 Keypad Fault
3.9 Receiver Fault
3.10 Earphone Radio Silent
3.11 ExternalAudio radio Silent
3.12 No Signal
3.13 Fail to Recognize T-Flash Card
3.14 Earphone Fault
3.15 Camera ShootingAbnormalities
All manuals and user guides at all-guides.com

X249 L2 Service Manual
3.1 Structural Parts Fault
Replace structural parts by referring to mobile phone disassembly steps.
3.2 Fail to Start Up
YES
YES
NO
NO YES
YES
NO
YES
NO
YES
NO
YES
check battery installed correctly
& battery voltage >3.4v?
re-install & recharge
check the connection between LCD
module and PCBAis reliable（cable
and LCD，cable with PCBA）
and LCD，cable with PCBA）
reassemble
replace LCD and make bad marks
re-download
normally download, keep
parameter when download
replace PCB
make bad mark on the bad PCBA
referring to PCBA Repair Instructions
OK
replace non-defective LCD
module to make sure if normal
fail to start up
All manuals and user guides at all-guides.com

X249 L2 Service Manual
3.3 No Ringtone
YES
YES
NO
NO
No
YES
NO
YES
NO
check solder of speaker is
ok?
repair welding of speaker
replace speaker
check if the speaker
circuit is normal
replace speaker
OK
amend the mainboard referring to
its repair instructions
replace the
mainboard
no ring tone
All manuals and user guides at all-guides.com

X249 L2 Service Manual
3.4 LCD Abnormal Display
YES
YES
NO
NO
YES
NO
No YES
NO
LCD abnormal display
check if the LED is damaged
replace LCD
analyze the circuit according to the
mainboard to make sure if it is the
mainboard problem
replace the mainboard
OK
amend the mainboard referring to its
repair instructions
check if LCD’s welding
part is pseudo welding
weld LCD and TP’s welding parts
All manuals and user guides at all-guides.com

X249 L2 Service Manual
3.5 Charging Fault
YES
YES
NO
NO
YES
NO
NO
check again by replacing battery
or charger
replace battery or charger
weld connector
repair the mainboard
check if the battery and charger
connector is soldering or missing
charging fault
OK
refer to the mainboard repair instructions
replace the main board
All manuals and user guides at all-guides.com
all-guides.com

X249 L2 Service Manual
3.6 Fail to Identify SIM Card
YES
YES
NO
YES
NO
YES
NO
replace SIM card
check if SIM
connector is
soldering
weld SIM connector
check the periphery circuit of
SIM connector is normal
repair the mainboard by referring to
the mainboard repair instructions
check the connective way of
SIM card or replace SIM card
fail to identify SIM card
OK
replace the mainboard
All manuals and user guides at all-guides.com

X249 L2 Service Manual
3.7 No Echo, Fail to Record (But There Has Ringtone)
YES
YES
NO
YES
NO
Yes YES
NO
YES
NO
check MIC for soldering
defect
solder or replace MIC
replace the mainboard
no echo, fail to record (but there has ring tone)
check if MIC sound
hole is jammed
replace MIC and make bad
marks on the bad MIC
OK
replace MIC
clean MIC sound hole
check the periphery circuit of
MIC connector is normal
repair the mainboard by referring to
the mainboard repair instructions
All manuals and user guides at all-guides.com

X249 L2 Service Manual
3.8 Keypad Fault
YES
NO
NO
NO
YES
NO
YES
NO
YES
NO
check if the keypad is
assembled correctly
reassemble the keypad
re-paste the DOME
Is structural parts related to
DOME?
amend the related structural parts
check DOME is pasted correctly
keypad Fault
OK
analyze the circuit of the
mainboard keypad part
repair the mainboard by referring to
the mainboard repair instructions
replace the mainboard
All manuals and user guides at all-guides.com

X249 L2 Service Manual
3.9 Receiver Fault
YES
YES
NO
YES
NO
NO
YES
NO
NO
weld the pseudo-welding part
replace the mainboard
check if receiver is pseudo
welding
no voice in receiver
OK
replace the receiver
replace receiver
check the periphery circuit
of MIC connector is normal
repair the mainboard by referring to
the mainboard repair instructions
All manuals and user guides at all-guides.com