MicroNet SP390I User manual

Communicate via
Quick Installation Guide
Model No.: SP390I
P/N 2300-0653
6
5
7
WEEE Directive & Product Disposal
At the end its serviceable life ,this product should not be treated
as household or general waste. It should be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment, or returned to the supplier for disposal.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class B for ITE, the
essential protection requirement of Council Directive 89/336/EEC
on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it
may be possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form
without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their
respective companies.
Copyright © 2011, All Rights Reserved.
Power over Ethernet Injector
Switch
Ethernet Cable
SP390I
Power over Ethernet
Injector
Power Cord
Specifications
Standards
Interface
Pin Assignment
and Polarity
Output Power
Voltage
User Port Power
Connectors
Operating
Temperature
Storage
Dimension
Weight (g)
Power Supply
Emission
IEEE802.3, 10BASE -T
IEEE802.3u,100BASE-TX
IEEE802.3ab, 1000Base-T
IEEE802.3af, IEEE802.3at
10/100/1000 Mbps, RJ-45 x 2 (Data In x1;
Data and Power Out x 1)
1/2 (+), 3/6(-)
52Vdc
30 Watts
Shielded RJ-45, EIA 568A and 568B
o o
-10 - 45 C
o o
-20 - 70 C
145 x 60 x 40 mm ( W x L x H )
0.350kg
Input: 100-240V, 50/60Hz
Output: 52VDC, 30Watts
FCC Class B,CE
WARNING:
Connect the injector with splitter only. Connecting the injector
directly to other devices may cause serious damage!
IP Camera with PoE
www.micronet.com.tw

4
3
1 2
Key Features
Up to 30W of power on 2-pairs
IEEE 802.3at compliant with 2-event classification
IEEE 802.3af backward compatible
Compatible with all IEEE 802.3af or legacy
Safe and reliable power to any PoE powered devices, i.e. WiFi
AP & IP camera
Automatic detection and protection of non-standard Ethernet
Terminals
Supports 10/100/1000Base-T applications
Introduction
Micronet SP390I is a single port, high-power solution for remote
powering of current and emerging high power applications.
Generating up to 30W, SP390I enables remote power for a new
range of applications including 802.11 Access Points, pan-tilt-zoom
(PTZ) cameras and video-phones. It complies to IEEE 802.3at PoE
standard and is backward compatible to IEEE802.3af. It can power
both existing 10/100Base-T network devices and emerging wireless
1000Base-T devices such as IP camera and wireless IEEE 802.11n
access points.
Package Contents
Before you start installing the device, verify the following items are
in the package:
SP390I Injector
Quick Installation Guide
Power Cord
Physical Description
DATA/IN port: Connect to switch/hub for data input.
P+D/OUT port: It is a RJ-45 Ethernet port and has a fix RJ-45
cable for data and power output.
AC/IN 100-240V: The POWER IN port is for supporting the power
into injector.
SP390I front view
SP390I back view
Installation
To install the SP390BI injector, please follow below steps.
1. Use RJ-45 cable from the Data/IN port on the Power over
Ethernet Injector to the Switch/HUB.
2. Use RJ-45 cable from the P+D/OUT port on the Power over
Ethernet Injector to the PoE Splitter, PD (Such as WLAN Access
Point…etc.).
3. Plug in the power cord of the Power over Ethernet Injector to
the appropriate power source.
4. Before starting, make sure all connections are correct.
1.
1.
1.
1.