MicroNet SP916NL User manual

6
5
7
WEEE Directive & Product Disposal
At the end its serviceable life ,this product should not be treated
as household or general waste. It should be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment, or returned to the supplier for disposal.
P/N 2300-0679
Note: Two kinds of fast access methods are provided on the
router's web-based utility: ADSL dial-up and DHCP.
2. If you select ADSL dial-up, you only need to enter the access
account and access password as well as the wireless password,
and then click “Ok” to complete the settings.
3. If you select DHCP, you only need to enter the wireless
password and click “Ok” to complete the settings.
2.
2.
2.
Communicate via
Quick Installation Guide
Model No.: SP916NE/SP916NL
300Mbps/150Mbps Wireless
LAN Broadband Router
www.micronet.com.tw
SP916NE
SP916NL
The default access method is ADSL dial-up and the access account
and access password are the same as the ADSL dial-up account
and password, which you can inquire your broadband ISP. For
other access methods, please refer to WAN settings in chapter
4.The wireless password can only consist of 8 characters, the
default is 12345678 and you can modify it when necessary.
Search the AP router through Wireless network
1. On the PC site, disable the LAN adapter and enable the
wireless adapter.
2. Use the adapter's utility to browse the wireless network
in neighborhood.
3. Find the AP router's name; click the item to open the
configuration page then key in the SSID that was set in the AP.
Save the setting then the PC can join the network of this AP.
4. Now, the PC can access Internet through this AP router.
5.For further settings of this AP router, please refer the manual
on the CD.
1.
1.
1.
1.
1.
Micronet
*********

Hardware Installation
Attach the power adapter to the 'Power' socket of the router
and wall socket.
Connect the xDSL / cable modem to the WAN port of router
by Ethernet cable.
Connect all computers and network devices to the LAN port
(1~4) of the router.
4
3
1 2
Introduction
Micronet SP916NE/SP916NL, 300Mbps/150Mbps Wireless
Broadband Router, delivers next generation wireless solution of
high speed and cost-efficient network. It is compliant with IEEE
802.11n and backward compatible with IEEE 802.11b/g. Best
selection for small office and home application where all computers
and network devices can share Internet access through a single
xDSL/cable modem. In addition, the scope of the network can be
easily expanded by connecting the router to a hub or switch.
Package Contents
Prior to the installation of the device, please verify the following
items are in the package:
WLAN Broadband Router
Quick Installation Guide
User Manual & Utility CD
Power Adapter
RJ-45 1m cable
2.Select 'Obtain an IP address automatically' and 'Obtain
DNS server address automatically', then click <OK>.2.
Configuration
Follow the steps below to configure and set up WLAN Broadband
Router. Acomputer with wired Ethernet connection to the
wireless router is required for first time configuration.
IP Address Configuration
PC/Notebook must belong in the
same IP range and subnet. Follow
the steps below to configure IP
settings for LAN PC.
1.In the control panel, double click
on Network Connections. Double
click on the local area connection
(e.g. LAN). The following screen
will appear. Highlight 'Internet
Protocol (TCP/IP)' and click on
'Properties'.
1.
1.
1.
1.
1.
1.
Default Values
Web-based User Interface
SP916NE/SP916NL is embedded with http sever and provides a
series of web pages, which display the configuration and status of
the system. After configuration of IP, the management interface can
be access by entering the IP address of the AP into the browser.
IP Address
Subnet Mask
Password
192.168.1.1
255.255.255.0
'1234'
3.In DOS command, type 'ipconfig' to view information on LAN
connection. Ensure the IP address and subnet mask are on the
same subnet as the router.
2.
2.
1. Login page will appear to prompt users to enter the username
and password.1.