MicroNet SP6008PWS User manual

User’s Manual
8-Port Web Smart Switch with PoE
Model No.: SP6008PWS
http://www.micronet.info

Table of Contents
Chapter 1 Introduction................................................................................... 1
1.1 Key Features.................................................................................... 1
1.2 Package Contents............................................................................ 1
Chapter 2 Hardware Installation.................................................................... 2
2.1 Hardware Installation ....................................................................... 3
Chapter 3 Web Administration ...................................................................... 9
3.1 Administrator.................................................................................... 9
3.2 Port Management .......................................................................... 12
3.3 VLAN Setting ................................................................................. 14
3.4 QoS Setting.................................................................................... 15
3.5 Port Security .................................................................................. 17
3.6 Logout ............................................................................................ 18
Chapter 4 Specification ............................................................................... 19

1
Chapter 1 Introduction
Micronet SP6008PWS 8-Port Web Smart Switch with PoE offers Broadcast storm
protection, Port-based VLAN and QoS to manage your networks. Moreover, it
automatically detects the presence of IEEE 802.3af-compliant devices (PD) and supplies
power to each appliance such as IP Camera, VoIP, and Wireless Access Point.
1.1 Key Features
●Compliant with IEEE 802.3af standard
●Each PoE port supplies power up to 15.4Watts
●Support broadcast storm protection
●Support short-circuit protection
●Support port-based VLAN
●Support port security setting
●Support one key multi to one VLAN setting
●Support remote management
Note: Contact your dealer immediately if any of the above items are missing, damaged, or
if the unit does not work.
1.2 Package Contents
Before you start installing SP6008PWS, please verify the following package contents:
ySP6008PW 8-Port Web Smart Switch with PoE
yQuick Installation Guide
yManual CD
yPower Cord
Note: Contact your local dealer immediately if any of the above items are missing,
damaged, or the unit does not work.

2
Chapter 2 Hardware Installation
Front Panel
RJ-45 PoE ports and LED indicators
Back Panel
Work with AC 90-260V AC, 50-60Hz.
LED Indicator
For definitions of LED indicators, please refer to the following table:
LED Status Color Description
On Yellow Power On
POWER Off -- Power is not connected.
On Green The Ethernet port is
connecting with the device.
Blink Green Receiving or transmitting
data.
LINK/ACT
Off -- No device attached.
On Yellow
Power is transmitting to the
device
PoE
Off -- Power is not transmitting to
the device

3
2.1 Hardware Installation
The setup of the Switch can be performed using the following steps:
Step 1: Connect a RJ-45 Ethernet cable from IEEE802.3af-compliant devices (PD) to an
available PoE port of SP6008PWS.

4
Step 2: Make sure the power switch on the rear panel of the SP6008PWS is turned
off(O). Connect the AC Power Adaptor to SP6008PWS and then to a power
outlet.

5
Tour the system
The configuration of the switch can be performed using the following steps:
Step1:
•Click the Start button followed by Control Panel.
• In the Control Panel, double-click the Network Connections.
• In the Network Connections window, double-click Local Area Connection.

6
Step 2:
• Click Internet Protocol (TCP/IP) from the components list and then click the
Properties
Step 3:
• In the Internet Protocol (TCP/IP) Properties window,
click the Use the following IP address.
• Enter the following information:

7
IP Address: 192.168.2.xxx ( xxx = 2~254)
Subnet Mask:
255.255.255.0
Note: Do not use 192.168.2.1 as this address is reserved for
the web management tool.
Step 4:
Step 5:
• The Login screen will show up.

8
Step1:
Step:
• Login in with User Username:admin
Password :admin
• Click OK

9
Chapter 3 Web Administration
On the following home page, select the configuration by clicking the icon. It includes,
- Administrator
- Port Management
- VLAN Setting
- QoS Setting
- Port Security
- Logout
3.1 Administrator
Administrator: Configuration

10
You can change the user name and the password, and click “Update” to confirm the new
change. After that, you can reset this switch by power off and then power on to take the
new user name and the password effectively.
Administrator: System IP Configuration
You can change the IP address by typing the new IP address and click “Update” to confirm
the new change, and then the message will show “Setting Process OK!!”, After that, you
should reset this switch by power off and then power on it to complete the new change.
Administrator: System Status

11
It shows this switch MAC address, and you can select “Back to the last display” or “Logout”
when the time’s out.
Administrator: Load Default Setting to EEPROM
You can click “Load” to load the new factory default setting, and then reset the switch by
power off and then power on to take it effectively.
Administrator: Firmware Update

12
Follow the instruction on the screen to update the new firmware. Please contact with your
sales agents to get the latest firmware information.
3.2 Port Management
Port Management: Port Control Configuration
Select the “Port No.” which you want to configure the mode below,
“Capability” - Auto-Nego. or force on 100M or 10M mode
“Duplex” - you can select the port is full/half-duplex or enable/disable this port.
Port Management: Bandwidth Control

13
Select the “Port No.” which you want to configure the mode below,
“TX Rate” is meant you can set the maximum transmission rate of this selected port and
choose the full speed or in 128K/256K/512K/1M/2M/4M/8M speed.
“RX Rate” is meant you can set the maximum receiving rate of this selected port and
choose full speed or in 128K/256K/512K/1M/2M/4M/8M speed.
Port Management: Broadcast Storm Control

14
You can enable or disable the broadcast storm protection feature by clicking “Update”.
Port Management: Max Packet Length
You can select the maximum packet length setting, 1536 byte or 1552 byte of this switch.
3.3 VLAN Setting
VLAN Setting: Group VLAN Setting

15
There are 4 VLAN groups, 01, 02, 03, 04, can be used.
You can select a group, and then click the port number which you want to put it into the
selected VLAN group.
VLAN Setting: Multi to 1 Setting
This is a special design for easily setting the switch VLAN into “VLAN Per Port“. After this
setting, all ports can only connect to the destination port.
3.4 QoS Setting
QoS Setting: Class of Service Configuration

16
You can select the class of service for each port.
QoS Setting: High Priority Queue Configuration
You can select WRR low weight 1/4 or 1/8.
QoS Setting: Customization Diffserv

17
Please follow the instruction on the screen to update the setting.
3.5 Port Security

18
When this function is enabled, the port will record the first receiving source MAC address
as the security MAC address and only allow the packet which has this MAC address to
activate on the port.
3.6 Logout
You can click “Logout” to logout.