MicroNet SP6005P4 User manual

5
Quick Installation Guide
5-Port 10/100M PoE Switch, 4 PoE Ports
Model No.: SP6005P4
6
FCC Certifications
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and radiates radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at own expense. This
device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received; including interference that may cause
undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility of the essential protection
requirement of Council Directive 89/336/EEC on the
approximation of the laws of the Member States. Company has
an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date.
Please check with your local distributors for the latest
information. No part of this document can be copied or
reproduced in any form without written consent from the
company.
P/N: 2300-0580
7
WEEE Directive & Product Disposal
At the end its serviceable life ,this product should not be treated
as household or general waste. It should be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment, or returned to the supplier for disposal.
Note:
1. Ports 1 to 4 are used for connecting to PD or PoE splitter for
end devices.
2. For high power applications, the PD or PoE splitter has to be
ompliant with pre-802.3at standard.
3. Port 5 is the RJ-45 uplink port that connects with non-PoE
Device.
1.
1.
1.
c
For cable selection, refer to the following table:
10M
Cat. 5,5e UTP/STP
Cat. 3,4,5,5e UTP/STP
Max. Length
100M
Network Speed Cable Type
100 meters
100 meters
Note:
To prevent costly equipment damage and downtime, please
consider installing a surge suppression device or a UPS (Un-
interrupted Power Supply).
Specifications
Standards
Hardware
Features
Power Supply
Environment
Dimension
Emission
IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX
IEEE 802.3af / pre-802.3at Power over Ethernet
1 x RJ-45 ports of 10/100M (#5)
4 x RJ-45 PoE ports of 10/100M (#1 - #4)
MAC address: 2K
Buffer memory: 512KB
Auto negotiation for 10/100M ports
Auto MDI/MDI-X for 10/100M ports
Max. 61.6W system feeding power
Deliver high power 48/30/20W for 1/2/3 PDs
OVP (Over Voltage Protection)
OCP (Over Current Protection)
OTP (Over Temperature Protection)
SCP (Short Circuit Protection)
Surge protection
LED indicators for PoE activity
DC 48V, 1.25A
Operating Temperature: 0 55 degree C
Storage Temperature: -20 90 degree C
Relative Humidity: 10 to 90%
120 x 90 x 28 (mm)
CE
Module SP6005P4
Web: www.micronet.com.tw ; www.micronet.info

LED Indicator
For definitions of LED indicators, please refer to the following
table:
4
1 2
3
Hardware Installation
The setup of the switch can be performed using the following
steps:
Step 1: Connect the AC Power Adaptor to SP6005P4 and then
to a power outlet.
Step 2: Enable PoE port manually with dip switch 'On'.
Step 3: Connect a RJ-45 Ethernet cable from IEEE802.3af-
compliant devices (PD) to an available PoE port of
SP6005P4.
Step 1:
Step 1:
Step 1:
Tour of the System
Front Panel
LED indicators, dip switch and one uplink port
Dip Switch Configuration
The DIP switch can be switched 'ON' or 'OFF' anytime for PoE
function enabled/disabled.
On/Green
Power is off
Power is on
Operation
The Ethernet port is connecting
with the device.
On/Green
Blink/Green
POWER
Off
LED Status
LINK
Off
Introduction
The SP6005P4 supports IEEE 802.3af and pre-802.3at standards
for Power over Ethernet (PoE) with the maximum power delivery
up to 48 Watts. That makes it suitable to various applications that
demand for remote power feeding and meet high level requirement
for power. In addition, the SP6005P4 is equipped with DIP switch
for per-port PoE enabled/disabled. It effectively helps allocate
power for connected devices and enhances network management.
Key Features
Compliant with IEEE 802.3af and pre-802.3at standards
Supports Power over Ethernet on 4 RJ-45 ports of 10/100M
Provides 61.6W (max) feeding power to 4 PDs: 15.4W for each
Able to delivers high power to 1/2/3 PDs: 48/30/20W for each
Supports power protection as OVP (Over Voltage Protection),
OCP (Over Current Protection), OTP (Over Temperature
Protection), and SCP (Short Circuit Protection)
Supports robust surge protection
Equipped with DIP switch for per-port PoE enabled/disabled
LED indicators for PoE activity
Package Contents
Before you start installing SP6005P4, please verify the following
package contents:
SP6005P4 10/100M PoE Switch
Quick Installation Guide
AC/DC Power Adaptor
Power Cord
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Back Panel
RJ-45 PoE ports and work with DC48V/1.25A adaptor
PoE
Receiving or transmitting data.
No device attached.
On/Green
Off
PoE port is active.
PoE port is not active.
*48
1
Maximal power on
Each PoE Port (Watts)
Number of Enabled
PoE Ports 234
*30 *20 15.4
Note:
1. It is suggested that the dip switch is set ready before the PoE
port is connected.
2. (*) The SP6005P4, with pre-802.3at compliant, provides
Extended power levels 48/30/20 watts for higher power
applications.
1.
1.
1.
1 2 34
OFF
ON
PoE Control