MicroNet SP6008P User manual

Communicate via
P/N 2300-0622
Quick Installation Guide
Model No.: SP6008P
8-Port 10/100M
PoE Switch
6
5
7
Specifications
SP6008PModel No.
IEEE 802.3af
IEEE 802.3 10 BaseT
IEEE 802.3u 100 BaseTX
IEEE 802.3x Flow Control
Number of Ports: 8 PoE/PSE ports
MAC Address: 1k
Buffer Memory: 512 bits
Transmission Method: Store and Forward
100Mbps port-148,800pps
10Mbps port-14,880pps
10 BaseT Cat 3,4,5 UTP/STP
100M BaseTx CAT 5 UTP/STP
Per Port: Link/Act, PoE Act/Status
Per Unit: Power
Input: 100~240V/AC, 50~60 Hz
Output: 48V/DC Per Port Output- 15.4W
Max Per Port, 8 Ports at Full 15.4 W Output Supported
130 Watts (Max)
20(H) x 58(W) x 87(D) mm
Operating: 0~60oC, Storage: -20~90oC
Operating: 10~90% (Non-Condensing)
Standards
Features
Filtering/
Forwarding
Rates
Transmission
Media
LED
Indicators
Power
Input/Output
Power
Consumption
Dimension
Temperature
Humidity
FCC Certifications
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at own expense. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility of the essential protection requirement
of Council Directive 89/336/EEC on the approximation of the laws of
the Member States. Company has an on-going policy of upgrading
its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the
latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
WEEE Directive & Product Disposal
At the end its serviceable life ,this product should not be treated
as household or general waste. It should be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment, or returned to the supplier for disposal.
www.micronet.com.tw ; www.micronet.info

Tour of the System
Front Panel
Back Panel
LED indicators
For definitions of LED indicators, please refer to the following table:
Introduction
Micronet SP6008P supports IEEE 802.3af at standard for Power
over Ethernet (PoE) with the maximum power delivery up to 130
Watts. That makes it suitable to various applications that demand
for remote power feeding and meet high level requirement for
power. SP6008P is totally equipped with 15.4 Watts per PoE port,
which effectively helps allocate power for connected multiple
devices and enhances network management.
Micronet SP6008P supports IEEE 802.3af at standard for Power
over Ethernet (PoE) with the maximum power delivery up to 130
Watts. That makes it suitable to various applications that demand
for remote power feeding and meet high level requirement for power.
SP6008P is totally equipped with 15.4 Watts per PoE port, which
effectively helps allocate power for connected multiple devices and
enhances network management.
Key Features
Compliant with IEEE 802.3af standard
Supports Power over Ethernet on 8 RJ-45 ports of 10/100M
Provides 130W (max) feeding power to 8 PDs: 15.4W for each
Supports Auto-MDI/MDI-X
Support Non-Blocking Data Forward
Supports Auto-Negotiation and feature of store-and-forward
LED indicators for PoE activity
Package Contents
Before you start installing SP6008P, please verify the following
package contents:
SP6008P 10/100M PoE Switch
Quick Installation Guide
Power Cord
Mounting Kits
4
3
1 2
LED Status
PWR
10/100M, LINK
PoE
Indication
On/Green
Off
On/Green
Blink/Green
Off
On/Orange
Off
Power is On
Power is off
The Ethernet port is connecting with
the device
Receiving or transmitting data
No device attached
PoE port is active
PoE port is not active
Power Switch and Power Cord Connector
Hardware Installation
Note: Port 1 to Port 8 are used for connecting to PD or PoE splitter
for end devices.
Note:
Network Speed Cable Type
10M
100M
Max. Length
Cat. 3,4,5,5e UTP/STP
Cat. 5,5e UTP/STP
100 meters
100 meters
Step 1: Connect the Power Cord to SP6008P and then to a power
outlet
Step 2: Connect a RJ-45 Ethernet cable from IEEE802.3af-
compliant devices (PD) to an available PoE port of
SP6008P
Step 1:
Step 1:
Step 1:
Note: To prevent costly equipment damage and downtime, please
consider installing a surge suppression device or a UPS
(Un-interrupted Power Supply).
Note:
Note:
For cable selection, refer to the following table:
The setup of the switch can be performed using the following steps: