MicroNet SP616R User manual

Quick Installation Guide
EtherFast 10/100Mbps Switch
Model No.: SP616R
Website http://www.micronet.info

1
Introduction
Micronet SP616R provides powerful, high-performance Ethernet
switch, with all ports capable of 10 and 100Mbps auto-negotiation
operation.
Store-and-forward switching mode promises the low latency plus
eliminates all the network errors, including runt and CRC error
packets. To work under full-duplex mode, transmission and
reception of the frames can occur simultaneously without causing
collisions as well as double the network bandwidth.
The switch is plug-n-play without any software to configure and also
fully compliant with all kinds of network protocols. Moreover, the
diagnostic LEDs on the front-panel can provide the operating status
of individual port and whole system.

2
Package Contents
Before you start installing the device, verify the following items are in
the package:
yOne SP616R Ethernet Switch
yQuick Installation Guide
yOne power cord
yRack-Mount accessories
Features
yComplies with 10Base-T/100Base-TX specifications of the
IEEE802.3/802.3u standard
ySupport Auto-Negotiation function to automatically select
optimal speed (10/100Mbps) and mode (Full/Half Duplex)
y8K MAC address table
y4 Mbyte memory buffer
ySupport auto uplink, no more cross-over cable
yForward and filter packets at non-blocking, full wire speed
y19-inch standard rack-mountable design
y100 - 240V AC, universal internal power supply

Physical Description
SP616R front view
SP616R rear view
Please refer to the following table for LED definition
LED Status Operation
Steady Green Power is on
Power Off Power is off
Steady Green A valid link is established
Off No link is established
LINK/ACT
Blinking Green Transmitting or receiving data
3

Installation
Micronet SP616R Switches do not require software configuration.
Users can immediately use any of the features of this product simply
by attaching the cables and turning on the power.
Rack Mounting
The switch can be mounted in an EIA standard 19-inch rack, which
can be placed in a wiring closet with other equipment. Attach the
mounting brackets at the switch’s front panel (one on each side),
and secure them with the provided screws.
Then, use screws provided with the equipment rack to mount each
switch in the rack.
Station Connections
Connect each station to the switch by twisted-pair cable. Plug one
RJ-45 connector into a RJ-45 port of the switch, and plug the other
RJ-45 connector into the station’s network adapter. Power on the
switch and then system is ready.
It supports Auto-Negotiation function to automatically select optimal
4

5
speed (10/100Mbps) and mode (Full/Half Duplex). If the attached
device does not support auto-negotiation or has auto-negotiation
disabled, an auto-sensing process is initiated to select the speed
and set the duplex mode to half-duplex.
Switch-to-switch Connections
In making a switch interconnection, you could use any port to
connect another switch with straight or crossover cable. As all the
ports support auto-uplink (MDI / MDI-X) function, using a
straight cable to make a switch-to-switch connection is
allowed.
Cable Selection
Refer to the following table：
Network Speed Cable Type Max. Length
10Mbps Cat. 3, 4, 5 UTP/STP 100 meters
100Mbps Cat. 5 UTP/STP 100 meters
Note: To prevent costly equipment damage and downtime, please
consider installing a surge suppression device or a UPS
(Un-interrupted Power Supply).

Network Application
6

7
Specifications
Standard IEEE802.3, IEEE802.3u
IEEE802.3x : Flow Control
Interface 16 * RJ-45 ports (10/100Mbps)
Cable Connections 10BASE-T: Category 3, 4, 5 UTP/STP
100BASE-TX: Category 5 UTP/STP
Network Speed 20M(Full duplex)/10M(Half duplex)
200M(Full duplex)/100M(Half duplex)
Features Auto-negotiation, Auto Uplink
Switch Fabric 3.2Gbps
Memory 4 MByte
MAC Address Table 8K entries
Forwarding Method Store and Forward
Filtering/Forwarding
Rate 10Mbps: 14,880pps/14,880pps 100Mbps: 148,800pps/148,800pps
Emission FCC Class A, CE
Operating Temperature 0o ~ 55o C (32o ~ 131o F)
Operating Humidity 10% - 95% (Non-condensing)
Dimension & Weight 441 x 130 x 44 mm, 1.34kg
Power Supply 100 - 240V AC, 50/60 Hz
Full range internal power supply

FCC Certifications
This Equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received; including interference that may cause
undesired operation.
8

CE Mark Warning
This equipment complies with the requirements
relating to electromagnetic compatibility, EN 55022
class A for ITE, the essential protection requirement of Council
Directive 89/336/EEC on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it
may be possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form
without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their
respective companies.
Copyright © 2004, All Rights Reserved
P/N: 2300-0233
9