Midea FS40-14BU User manual

OWNER’S MANUAL
16" STAND FAN
MODEL:FS40-14BU
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the IM are for reference only.

1
Read Rules for Safe Operation and Instructions Carefully.
CAUTION
1. If the supply cord is damaged, it must be replaced by manufacturer
or its service agent or a similarly qualified person in order to avoid
a hazard.
2. To protect against the risk of electrical shock, do not immerse the
unit, cord or plug in water or other liquid.
3. This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
4. When the appliance is not in use and before cleaning, unplug the
appliance from the outlet.
5. Keep electrical appliances out of reach from Children or infirm
persons. Do not let them use the appliances without supervision.
6. When the fan was assembled, the rotor blade guard shall not be
taken off anymore
- Prior cleaning unplug the fan.
- The rotor guard shall not be dissembled/opened to clean the
rotor blades.
- Wipe the fan enclosure and rotor blade guard with a slightly
damp cloth.
WARNING
1. Never insert fingers, pencils, or any other object through the grille when fan is
running.
2. Disconnect fan when moving from one location to another.
3. Be sure fan is on a stable surface when operating to avoid overturning.
4. DO NOT use fan in window, rain may create electrical hazard.
5. Household use only.
RULES FOR SAFE OPERATION

2
PART FIGURE
1. Screw
2. Front guard
3. Spinner
4. Blade
5. Rear guard
6. Oscillation knob
7. Power switch
8. Motor
9. Screw
10. Neck
11. Tighten knob
12. Nut
13. Connecting column
14. Internal pole
15. Height adjustment ring
16. External pole
17. Base
21
20
1
2 3 4 5 6 7
8
9
10
11
13
14
15
16
17
18
19
12
1. Unscrew the 7-shape Bolt from the Extension Pole. (Fig.1)
2. Insert the extension pole in the base and tighten the 7-shape Bolt. (Fig.2)
3. From the extension pole loosen the height adjustment ring and adjust the internal
pipe to the desired height. (Note: If you can’t find the internal pole, it slides inside
the extension pole. You can pull it out from the extension pole.) (Fig.3)
4. To attach the head unit to the extension pole, loosen the thumb screw on the
bottom of the head unit. Place the head unit on the extension pole and tighten the
thumb screw in alignment with the groove on the internal pole. (Fig.4)
CAUTION: Height adjustment ring must be fully fastened before the assembly of
the motor section to the extension pole.
ASSEMBLY OF BASE & COLUMN UNIT
Fig.1 Fig.2 Fig.3 Fig.4
18. Base Enclosure Cover
19. 7-shape Bolt
20. Spring card
21. Spring
Loosen

3
GUARD & FAN BLADE ASSEMBLY
The fan requires little maintenance. Do not try to fix it by yourself. Refer it to
qualified service personnel if service is needed.
1. Before cleaning and assembling, fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the
motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the surface.
Do not use any of the following as a cleaner: gasoline, thinner.
5. Do not allow water or any other liquid into the motor housing or interior parts.
MAINTENANCE INSTRUCTION
OPERATING INSTRUCTION
1. Speed is controlled by pressing the piano keys.
0---Off 1---Low 2---Medium 3---High
2. To make/stop the fan head oscillate. Push down/pull up the clutch knob.
3. The airflow can be adjusted upward or downward by loosening the tilt adjustment
knob and adjusted the vertical angle as desired. Retighten the knob securely.
4. The height of the fan can be adjusted by loosening the height adjustment ring
carefully raising or lowering the fan and firmly tightening the ring.
Fig.5 Fig.6 Fig.7
Screw
Screw
1. Install back mesh enclosure: take out front and back mesh enclosures as well as
the fan from the packing case. Disengage four set screws of mesh enclosure in the
most exterior rim of front casing of fan motor. Use the four set screws to fix the
back mesh enclosures on the motor (the handle of mesh enclosure faces
upwards). (See Fig.5)
2. Install fan blades: in the process of installation of fan blades, get the slot at back of
fan blades stuck in retaining pin of motor shaft. Then mount the spinner, and screw
up the spinner anticlockwise. (See Fig.6)
3. Install front mesh enclosure: take down the screws attached to the outer ring of
back mesh enclosure firstly. Take out front mesh enclosure from the packing bag.
Set right the trim ring of front mesh enclosure. Press the front mesh closure on the
back one and get them aligned. Pay attention to get the screw hole sites at outer
rings of front and back mesh enclosures aligned. Then screw up and tighten the
screws taken down in the screw hole sites. At last, press the mesh buckles at out
ring of mesh enclosure in proper order. (See Fig.7)