Mighty Mule MM362-D User manual

WARNING!
This equipment is similar to other gate or door equipment and meets or exceeds Underwriters
Laboratory Standard 325 (UL 325). However, gate equipment has hazards associated with its
use and therefore by installing this product the installer and user accept full responsibility for
following and noting the installation and safety instructions. Failure to follow installation and safety
instructions can result in hazards developing due to improper assembly. You agree to properly
install this product and that if you fail to do so GTO Access Systems, LLC, shall in no event be
liable for direct, indirect, incidental, special or consequential damages or loss of profits whether
based in contract tort or any other legal theory during the course of the warranty or at any time
thereafter. The installer and/or user agree to assume responsibility for all liability and use of this
product releasing GTO Access Systems, LLC, from any and all liability. If you are not in agreement
with this disclaimer or do not feel capable of properly following all installation and safety
instructions you may return this product for full replacement value.
READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to install and
use this automatic gate opener. This gate opener produces a high level of force. Stay clear of the
unit while it is operating and exercise caution at all times.
All automatic gate openers are intended for use on vehicular gates only.
Printed in China for GTO Access Systems, LLC.
This product meets and exceeds the requirements of UL 325, the standard which
regulates gate operator safety, by Underwriters Laboratories Inc.
GTO Sales: 800-543-4283 • Fax [phone]
GTO Technical Service 800-453-1236
For 24 hour/day, 7 day/week Technical Service visit http://support.gtoinc.com
For more information on Mighty Mule’s full line of Automatic Gate Openers and Access Controls visit www.mightymule.com
For more information on Mighty Mule’s full line of Automatic Gate Openers and Access Controls visit our website at www.mightymule.com
MM362-D
Installation Manual
Copyright©2015 GTO Access Systems, LLC rev 12.14.15

Converting Metric Units to English Equivalents
When You Know Multiply By To Find Symbol
centimeters 0.3937 inches in. (or ")
meters 3.2808 feet ft. (or ')
kilograms 2.2046 pounds lb. (or #)
Converting English Units to Metric Equivalents
When You Know Multiply By To Find Symbol
inches 2.5400 centimeters cm
feet 0.3048 meters m
pounds 0.4535 kilograms kg
Converting Temperature
deg. Celsius (°C x 1.8) + 32 deg. Fahrenheit °F
deg. Fahrenheit (°F-32) ÷ 1.8 deg. Celsius °C
Serial Number: ___________________________________ Date of Purchase: ________________
Place of Purchase:___________________________________________________________________
Please record the following information product serial number (located on the rear of opener arm), be sure to
keep all receipts for proof of purchase. Refer to this information when calling GTO for service or assistance
with your automatic gate opener.
FOR YOUR RECORDS
U.L. Gate Operator Classifications
Residential Vehicular Gate Operator—Class I: A vehicular gate operator (or system) intended for use in a home of
one-to-four single family dwelling, or a garage or parking area associated therewith.
Commercial/General Access Vehicular Gate Operator—Class II: A vehicular gate operator (or system) intended
for use in a commercial location or building such as a multifamily housing unit (five or more single family units), hotel,
garages, retail store, or other building servicing the general public.
Industrial/Limited Access Vehicular Gate Operator–Class III: A vehicular gate operator (or system) intended for use
in an industrial location or building such as a factory or loading dock area or other locations not intended to service the
general public.
Restricted Access Vehicular Gate Operator–Class IV: A vehicular gate operator (or system) intended for use in a
guarded industrial location or building such as an airport security area or other restricted access locations not servicing
the general public, in which unauthorized access is prevented via supervision by security personnel.
Product Usage
The Mighty Mule Gate Opener meets all of the safety requirements of a Class I Residential Vehicular Gate Operator and
is intended for use solely with vehicular swing gates in single-family residential applications.
The Mighty Mule Gate Opener system certified to be in compliance with the following safety standards (current edition as
of publication date):
Product in compliance with the latest UL-325 and UL-991 safety standards by ETL. Product in compliance
with CAN/CSA-C22.2 No. 247-92.
Product in compliance with IEC 60335-2-103:2003 and IEC 60335-1:2004, including A1:2004.

rev 12-14-15 Mighty Mule 362-D Installation Instructions i
Table Of Contents
Please Read This First ...................................................................................................ii
Important Safety Instructions .................................................................................. iii–viii
How to Manually Open and Close the Gate:..............................................................iii
For the Consumer.......................................................................................................Iv
Required Safety Precautions for Gates ......................................................................vi
Secondary Means of Protection Against Entrapment ............................................... vii
Entrapment Alarm (Ul 325; 30A.1.1A) ....................................................................... vii
Technical Specifications................................................................................................ 1
Before You Begin........................................................................................................... 2
Solar Panel and Gate Activity Chart............................................................................ 2
Parts List – Opener and Mounting Hardware ............................................................. 4
Tools and Materials..................................................................................................... 5
Installation Overview for Pull-To-Open Gates ............................................................. 6
Installation of the First Gate Opener ............................................................................. 7
Install Post Bracket Assembly and Gate Bracket ....................................................... 8
Attach Opener Arm................................................................................................... 10
Install the Closed Position Stop Plates..................................................................... 11
Mount the Control Box.............................................................................................. 12
Connect Opener Power Cables................................................................................ 13
Connect the Transformer ......................................................................................... 13
Connect Battery Harness to Control Board.............................................................. 15
Connect the Battery .................................................................................................. 16
Set the Closed Position Limit.................................................................................... 16
Adjust the Stall Force Setting ................................................................................ 17
Set Auto-Close Time................................................................................................. 17
Personalize Your Transmitter Setting ........................................................................ 18
Push-To-Open Installation Instructions ....................................................................... 19
Solar Panel Instructions............................................................................................... 21
Connecting Accessories and Safety Devices............................................................. 22
Troubleshooting Guide................................................................................................ 24
Gate and Opener Maintenance .................................................................................. 25
Warranty Repair........................................................................................................... 25
Accessories................................................................................................................. 26

ii Mighty Mule 362-D Installation Instructions rev 12-14-15
Thank you for purchasing a Mighty Mule 362-D Gate Opener—GTO’s “do-it-yourself” automatic gate opener!
When correctly installed and properly used, your Mighty Mule Gate Opener will give you many years of reliable
service. Please read the following information and watch the enclosed video to ensure you have the correct
system for your particular needs. Furthermore, this manual and the video will enable you to properly install
your Mighty Mule Gate Opener.
The Mighty Mule 362-D Gate Opener is designed for installation on Pull-To-Open dual gate leaves (gates
that open into the property). By purchasing accessory brackets [FM148], the Mighty Mule 362-D Gate Opener
can accommodate Push-To-Open dual gate leafs (gates that open out from the property). Please see
Pull-To-Open/Push-To-Open diagram on page 3. The gates must not exceed 12 ft. or 300 lbs. per leaf (see
Technical Specifications on page 1). The Mighty Mule Gate Opener can be used on vinyl, aluminum, chain
link, farm tube, and wrought iron gates.
Use on solid (surface) gates is not recommended. Solid surface gates have a high resistance
to the wind. If the wind is strong enough, the opener will obstruct and stop, blow fuses, or
may damage the equipment.
The Mighty Mule Gate Opener features an adjustable stall force setting. This safety feature makes the gate
stop and reverse direction within 2 seconds when it comes in contact with an obstruction. The MIN setting;
means the gate will exert the minimum force on an obstruction before it stops and reverses direction. You will
need to adjust the stall force for your particular application.
The Mighty Mule Gate Opener also has an adjustable auto-close feature. After the gate reaches the fully
open position, it can be set for OFF, or to remain open up from 3 to 120 seconds before automatically closing.
Pressing the transmitter button at any time after the gate opens fully will cause it to close immediately. The
auto-close factory setting is OFF, meaning the gate will stay open until you press the transmitter (or keypad,
etc.) again.
The Mighty Mule Gate Opener accommodates extra transmitters, digital keypads, solar panels, push buttons,
automatic gate locks, and other access control products. These optional accessories (page 26) are available
at Tractor Supply stores or through Special Order (if the accessory is not in stock). If your store cannot special
order accessories, please call the GTO Sales Department (800/543-GATE) or visit www.mightymule.com.
PLEASE NOTE—If your application requires any of the following:
Column Mounting
Slide gates
Swing gates longer than 12 feet or weighing more than 300 pounds
Professional installation
please call GTO at 800/543-GATE (4283) for information about our GTO/ACCESS SYSTEMS professional line
of gate openers and accessories. Our Sales Department will be glad to give you the name and phone number
of a GTO/ACCESS SYSTEMS dealer near you.
BEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPENER:
Watch the enclosed video and read these instructions carefully and completely to become familiar
with all parts and installation steps. The video is only designed as an overview of the installation
procedure. You must read the installation manual for detailed instructions on
gate opener safety and proper use of the gate opener.
PLEASE READ THIS FIRST

rev 12-14-15 Mighty Mule 362-D Installation Instructions iii
IMPORTANT SAFETY INSTRUCTIONS
Because automatic gate openers produce high levels of force, consumers need to know the potential
hazards associated with improperly designed, installed, and maintained automated gate opener
systems. Keep in mind that the gate opener is just one component of the total gate operating system.
Each component must work in unison to provide the consumer with convenience, security, and
safety.
This manual contains various safety precautions and warnings for the consumer. Because there are
many possible applications of the gate opener, the safety precautions and warnings contained in this
manual cannot be completely exhaustive in nature. They do, however, provide an overview of the
safe design, installation, and use of this product. CAREFULLY READ AND FOLLOW ALL SAFETY
PRECAUTIONS, WARNINGS, AND INSTALLATION INSTRUCTIONS TO ENSURE THE SAFE
SYSTEM DESIGN, INSTALLATION, AND USE OF THIS PRODUCT.
Precautions and warnings in this manual are identified with this warning symbol. The symbol
identifies conditions that can result in damage to the opener or its components, serious injury, or
death.
Because GTO automatic gate openers are only part of the total gate operating system, it is the
responsibility of the consumer to ensure that the total system is safe for its intended use.
How To Manually Open and Close the Gate:
CAUTION: The gate can be opened and closed manually when the opener is disconnected.
ONLY disconnect the opener when the opener power switch is OFF and the gate is NOT moving.
Disconnecting the Opener
1. Turn opener power switch (Control Box) OFF.
2. Remove hairpin clip, clevis pin, and bushing from both
the front and rear mounting points.
3. Remove the opener from the mount.
IMPORTANT: NEVER allow opener arm to hang
by the front or rear mount — it will break from
the arm weight.
CAUTION: Because the Mighty Mule gate opener is battery powered, disconnect the opener ONLY
when the power switch on the contol box is turned OFF. Unplugging the transformer does not turn power to
the opener OFF.
NOTE: Substitute a Pin Lock [FM133] for the clevis pin on the front
mount of the gate opener to prevent unauthorized removal of the opener
from the gate (page 26).
Clevis
Pin
Hairpin Clip
Gate Bracket
Front Mount
Bushing

iv Mighty Mule 362-D Installation Instructions rev 12-14-15
IMPORTANT SAFETY INSTRUCTIONS
Gate in the
Open Position
Gate in the
Open Position
ZONE 2
ZONE 3
ZONE 4
ZONE 5
Driveway
ZONE 1
ZONE 2
ZONE 4
ZONE 5
ZONE 3
For The Consumer
WARNING: To reduce the risk of injury or death:
1. READ AND FOLLOW ALL INSTRUCTIONS. Failure to meet the requirements set forth in the instruction manual
could cause severe injury or death, for which the manufacturer cannot be held responsible.
2. When designing a system that will be entered from a highway or main thoroughfare, make sure the system is
placed far enough from the road to prevent traffic congestion.
3. The gate must be installed in a location that provides adequate clearance between it and adjacent structures when
opening and closing to reduce the risk of entrapment. Swinging gates must not open into public access areas.
4. The gate and gate opener installation must comply with any applicable local codes.
I. Before Installation
1. Verify this opener is proper for the type and size of gate, its frequency of use, and the proper class rating.
2. Make sure the gate has been properly installed and swings freely in both directions. Repair or replace all worn
or damaged gate hardware prior to installation. A freely moving gate will require less force to operate and will
enhance the performance of the opener and safety devices used with the system.
3. Review the operation of the system to become familiar with its safety features. Understand how to disconnect the
opener for manual gate operation (page iii).
4. This gate opener is intended for vehicular gates ONLY. A separate entrance or gate must be installed for
pedestrian use (page vi).
5. Always keep people and objects away from the gate and its area of travel. NO ONE SHOULD CROSS THE
PATH OF A MOVING GATE.
6. Pay close attention to the diagram below and be aware of these areas at all times.
Entrapment Zones for a proper Pull-To-Open installation:
Zone 1 – leading edge of the gates.
Zone 2 – between the gate and the gate post.
Zone 3 – the path of the gate.
Zone 4 – the space between the gate in the open position and any object such as a wall, fence, etc.
Zone 5 – pinch points between the opener and gate.

rev 12-14-15 Mighty Mule 362-D Installation Instructions v
IMPORTANT SAFETY INSTRUCTIONS
II. During Installation
1. Install the gate opener on the inside of the property and fence line. DO NOT install an opener on the outside of the
gate where the public has access to it.
2. Be careful with moving parts and avoid close proximity to areas where fingers or hands could be pinched.
3. Devices such as contact sensors (safety edges) and non contact sensors (photo beams) provide additional
protection against entrapment.
4. If push buttons or keypads are installed, they should be within sight of the gate, yet located at least 10 feet from
any moving part of the gate (see diagram below). Never install any control device where a user will be
tempted to reach through the gate to activate the gate opener.
5. Do not activate your gate opener unless you can see it and can determine that its area of travel is clear of people,
pets, or other obstructions. Watch the gate through its entire movement.
6. Secure outdoor or easily accessed gate opener controls in order to prohibit unauthorized use of the gate.
Moving Gate
Area
Moving Gate
Area
Driveway
10'10'
10'10'
10'10'
NEVER INSTALL
any control device
within gray area
III. After Installation
1. Attach the warning signs (included) to each side of the gate to alert the public of automatic gate operation. It
is your responsibility to post warning signs on both sides of your gate. If any of these signs or warning decals
become damaged, illegible or missing, replace them immediately. Contact GTO for free replacements.
2. The gate is automatic and could move at any time, posing a serious risk of entrapment. No one should be in
contact with an activated gate when it is moving or stationary.
3. Do not attempt to drive into the gate area while the gate is moving; wait until the gate comes to a complete stop.
4. Do not attempt to “beat the gate” (drive through) while the gate is closing. This is extremely dangerous.
5. Do not allow children or pets near your gate. Never let children operate or play with gate controls. Keep ALL
gate controls away from children and unauthorized users; store controls where children and unauthorized users do
not have access to them.
6. KEEP GATE AND GATE OPENER PROPERLY MAINTAINED. Always turn power to opener OFF before
performing any maintenance. Regularly grease the gate hinges. Clean the push-pull tube with a soft, dry cloth and
apply silicone spray to it at least once per month.

vi Mighty Mule 362-D Installation Instructions rev 12-14-15
IMPORTANT SAFETY INSTRUCTIONS
7. To operate this equipment safely, YOU must know how to disconnect the opener for manual gate operation (page
iii). If you have read the instructions and still do not understand how to disconnect the opener, contact the GTO
Service Department.
8. Disconnect the opener ONLY when the power is TURNED OFF and the gate is NOT moving.
9. Make arrangements with local fire and law enforcement for emergency access.
10. Distribute and discuss copies of the IMPORTANT SAFETY INSTRUCTIONS section of this manual with all
persons authorized to use your gate.
11. IMPORTANT: Save these safety instructions. Make sure everyone who is using or will be around the gate
and gate opener are aware of the dangers associated with automated gates. In the event you sell the
property with the gate opener or sell the gate opener, provide a copy of these safety instructions to the
new owner.
Should you lose or misplace this manual, a copy can be obtained by downloading one from the Mighty
Mule web site (www.mightymule.com), by contacting GTO Access Systems, LLC., at 3121 Hartsfield Road,
Tallahassee, Florida 32303 or by calling 1-800-543-4283 and requesting a duplicate copy. One will be provided
to you free of charge.
Required Safety Precautions for Gates
Install Warning Signs
Warning signs alert people of automatic gate operation and are required when installing the Mighty Mule Gate Opener.
The Warning Signs included must be installed on both sides of each gate. Furthermore, a walk-through gate must be
installed if pedestrian traffic is expected near the vehicular gate. We recommend using the GTO Bulldog Pedestrian Gate
Lock [FM145] (page 26) for controlled access.
Entrapment Protection
GTO’s inherent obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily
injury in some circumstances. For this reason, safety devices such as safety edge sensors (or photoelectric sensors),
which stop and reverse gate direction upon sensing an obstruction, are suggested for enhanced protection against
entrapment.
Warning SignWarning Sign Contact Sensor
(recommended, not included)
Contact Sensor
(recommended, not included)
Pedestrian Gate
Bulldog Pedestrian
Gate Lock
(recommended, not included)
Vehicular GateVehicular Gate
Contact Sensor
(recommended, not included)
Contact Sensor
(recommended, not included)

rev 12-14-15 Mighty Mule 362-D Installation Instructions vii
IMPORTANT SAFETY INSTRUCTIONS
Secondary Means of Protection Against Entrapment
As specified by Gate Opener Safety Standard, UL 325 (30A.1.1), automatic gate openers shall have an inherent
entrapment sensing system, and shall have provisions for, or be supplied with, at least one independent secondary
means to protect against entrapment. The Mighty Mule utilizes Type A, an inherent (i.e., built-in) entrapment sensing
system as the primary type of entrapment protection. Also, the Mighty Mule has provisions for the connection of Type
B2 protection to be used as the secondary type of entrapment protection, if desired.
1. For gate openers utilizing a contact sensor (e.g., safety edge sensor– Type B2) in accordance with UL 325 (51.8.4
[i]):
A. One or more contact sensors shall be located at the leading edge, bottom edge, and post edge, both inside and
outside of a vehicular swing gate system.
B. A hard wired contact sensor shall be located and its wiring arranged so that the communication between the
sensor and the gate opener is not subjected to mechanical damage.
C. A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate opener for
entrapment protection functions shall be located where the transmission of the signals are not obstructed or
impeded by building structures, natural landscaping or similar obstruction. A wireless contact sensor shall
function under the intended end-use conditions.
You may want to consider adding photo beams to your installation. GTO Photo Beams [R4222] provide a “non contact”
means of entrapment protection.
Leading Edge Contact Sensor
on both sides of the gate
Post Edge Contact Sensor
on both sides of the gate
Bottom Edge Contact Sensor
on both sides of the gate
Post Edge Contact Sensor
on both sides of the gate
ENTRAPMENT ALARM (UL 325; 30A.1.1A)
The Mighty Mule Gate Opener is designed to stop and reverse within 2 seconds when the gate comes
in contact with an obstruction. Additionally, these openers are equipped with an audio entrapment
alarm which will activate if the unit obstructs twice while opening or closing. This alarm will sound for a
period of 5 minutes, or until the opener receives an intended signal from a hard wired entry/exit source
(e.g. push button control or keypad) and the gate returns to a fully open or fully closed position. Turning
the power switch on the control box OFF and back ON will also deactivate the alarm. Wireless controls
such as transmitters and wireless keypads will not deactivate the alarm.

viii Mighty Mule 362-D Installation Instructions rev 12-14-15
IMPORTANT SAFETY INSTRUCTIONS
Warning signs (4 enclosed) MUST be installed on both sides
of each gate (3–5 feet above the bottom of the gate)
!
Product identification label (2)
installed under rear mount of each arm
Control box label (1)
installed on front of the control box
Logo and warning labels (4)
installed on each side of opener housings
GTO DC SW202 Series
Conforms to UL325
5th Edition Standards
Serial No. MM362-0000000
XXXXXX
Gates That Open, LLC - Ta llahassee, Florida USA
TO MANUALLY OPEN AND CLOSE THE GATE
1.Turn opener power switch OFF.
2.Disconnect front and rear mount from mounting brackets.
3.Remove opener from mounting brackets and move gate.
Disconnect opener ONLY when the power switch is OFF and
the gate is not moving.
www.mightymule.com
1-800-543-GATE (4283)
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or play in gate area.
3. This gate is for vehicles only. Pedestrians must use separate entrance.
Maximum Gate: 300 lbs. (136.1 kg); 12 ft. (3.7 m) • Voltage: 12 Vdc;
Frequency: 0Hz; Power: 25W • Class I and II Vehicular Swing Gate Operator
AUTOMATIC GATE OPENER
MM362-D
®
by...

rev 12-14-15 Mighty Mule 362-D Installation Instructions 1
MIGHTY MULE 362-D GATE OPENER
_____________________________________ DRIVE _____________________________________
• Low friction screw drive (linear actuator) rated for -5 °F to +160 °F (-20 °C to +71 °C).
• Powered by a 12 V motor with integral case hardened steel gear reducer. Motor speed reduced to 260 rpm.
Generates 520 inch lb. of torque at 12 V.
• Maximum opening arc of 110°. Approximate opening time (90°): 18 seconds, depending on weight of gate.
_____________________________________ POWER _____________________________________
• The system is powered by a 12 Vdc automotive or lawn tractor battery.
• Battery charge is maintained by a 120 Vac, 14 Vac output transformer (10 VA) through the GTO control board] or
by optional GTO Solar Panels; the panel should generate minimum of 10 Watts (600 mA). A diode on the control
board prevents battery discharge. IMPORTANT: Never use both transformer and solar panel— this will damage
the battery and control board.
• One (1) blade-style fuse is rated for 15 A.
NOTE: The transformer should not be directly connected to any battery. Do not replace fuses with
higher ampere rated fuses; doing so will void your warranty and may damage your control board.
_____________________________________ CONTROL _____________________________________
• GTO microprocessor-based control board is set for dual leaf, pull-to-open gate installations. Jumper can be
removed to accommodate an optional kit for push-to-open gates.
• Control board has temperature compensated circuits.
• A circuit on the control board regulates charging. “Sleep draw” is 15 mA; “active draw” is 2 to 5 A.
• Auto-memorization of digital transmitter code.
• GTO RF receiver tuned to 318 MHz.
• Opener length with push-pull tube fully retracted is 26 3/8", mounting point to mounting point. Maximum stroke is
13".
• Adjustable auto-close timer (OFF to 3–120 seconds), and obstruction sensitivity (stall force).
• Power terminal block accommodates a transformer or solar panels.
• Accessory terminal block fully compatible with all Mighty Mule access controls.
• Control board allows connection of safety edge sensors and photoelectric sensors.
• Audio entrapment alarm sounds if unit encounters an obstruction twice while opening or closing.
_____________________________________ OPERATIONAL CAPACITY _____________________________________
• The Gate Capacity Chart shows approximate cycles, per day, you can expect from the Mighty Mule 362-D
Automatic Gate Opener when powered with a transformer. Actual cycles may vary slightly depending upon the
type and condition of gate and installation.
NOTE: BALL BEARING HINGES SHOULD BE USED ON ALL GATES WEIGHING OVER 250 LB.
To determine the number of cycles the gate opener will perform using solar panels, please see the specifications
listed on page 2 or call [phone] or [phone] for more information.
* These specifications are subject
to change without notice.
Gate Weight
Gate Length
Number of Cycles Per Day
Mighty Mule 362 Gate Capacity/Cycle Chart
Estimated number of daily cycles, based on use with a transformer.
300 lbs.
150 lbs.
100 lbs.
50 lbs.
39
41
44
46
5' - 6'
36
39
41
44
8'
34
36
39
42
10'
31
34
36
39
12'
An operation cycle is
one full opening and
closing of the gate.
Technical Specifications

2Mighty Mule 362-D Installation Instructions rev 12-14-15
1. Determine Charging Options for Battery: Transformer OR Solar
NEVER USE TRANSFORMER AND SOLAR PANEL(S) AT THE SAME TIME!
It will damage the control board!
IMPORTANT
• The Mighty Mule 362-D is designed and intended for use with a 12 Volt automotive or lawn tractor battery. The
battery must be placed inside a weatherproof case and located within 6' of the control box. The 8' battery
harness connects the battery to the control board.
• The battery charge is maintained by the 14 Volt transformer included OR optional solar panel(s). The transformer
OR solar panel is connected to the control board using low voltage, 16 gauge, dual conductor, multi-stranded,
direct burial wire [RB509] (page 26).
• All low voltage wire used with the Mighty Mule Gate Opener must be 16 gauge dual conductor, multi-stranded,
direct burial wire.
• The transformer is intended for indoor use. If the transformer can only be plugged into an outside electrical
outlet, a weatherproof cover or housing must be used.
• If your gate is more than 1000' from an AC power source, you will need to use a solar panel charging kit
(minimum 10 watts) . Refer to the Solar Panels and Gate Activity Chart below.
Solar Panel and Gate Activity Chart
The table and map illustrate the
maximum number of gate cycles
to expect per day in a particular
area when using from 10 to 20
watts of solar charging power. The figures
shown are for winter (minimum sunlight) and
do not account for the use of any accessory
items.
Accessories connected to your system
will draw additional power from the
battery and will require additional solar
panels.
NOTE: UP to 250 ft. of dual conductor, 16
guage, multi-stranded wire may be used
to allow installation of solar panels in direct
sunlight.
See page 26:
10 Watt Solar Panel [FM123]
5 Watt Solar Panel [FM121]
Dual Gate
Winter Ratings
Zone 1 Zone 2 Zone 3
10 Watts 8 16 26
15 Watts 11 20 30
20 Watts 14 28 38
Before You Begin

rev 12-14-15 Mighty Mule 362-D Installation Instructions 3
2. Check Direction of Gate Swing
The Mighty Mule is designed for PULL-TO-OPEN installations. PUSH-TO-OPEN installations require two Push-To-Open
brackets [FM148]. Push-to-Open Installation Instructions begin on page 19.
3. Prepare the Gates
• Gates must be plumb, level, and swing freely on their hinges.
• Wheels must NOT be attached to the gates.
• The gates must move throughout their arcs without binding or dragging on the ground.
• Note that gates over 250 lb. should have ball bearing hinges with grease fittings.
• The gate post should be be secured in the ground with concrete so it will minimize twist or flex when the opener
is activated.
• The addition of a horizontal or vertical cross member (if one is not already in place) to provide a stable area
for mounting the gate bracket is also important.
• Trench the driveway in order to lay PVC conduit for the second opener power cable (see illustration on page 6).
Your Property Your Property
Pull-To-Open
(arm retracts to open)
Push-To-Open
(arm extends to open)
Horizontal Cross Member
Vertical Cross Member
E
A
B
C
D
F
A – Level D – Posts Secured in Concrete
B – Plumb E – Centerline Mounting
C – Free Swinging F – Good Working Hinges

4Mighty Mule 362-D Installation Instructions rev 12-14-15
Parts List – Opener and Mounting Hardware
Hairpin Clip (4)
3/8" x 1-1/2" Clevis Pin (4)
5/16" x 1-1/2" Bolt (2)
3/8" x 1-1/2" Bolt (2)
3/8" x 2-3/4" Bolt (4)
3/8" x 8" Bolt (4)
8" Nylon Cable Tie (14)
3/8" Washer (12)
5/16" Washer (2)
3/8" Lock Nut (10)
5/16" Lock Nut (2)
Hardware Bag Contents
Gate Opener (2)
Installation DVD (1)
Gate Bracket (2)
Post Pivot Bracket (2)
3/8" Bushings (2)
Customer Support Card (1)
Post Bracket (2)
Closed Position
Stop Plate (2)
2" Mounting Screw (6)
®
E-Z GATE OPENER
Transformer (1)
RB502
Battery Wire
Harness (1)
Warning Signs (4)
Receiver Antena (1)
GTO Transmitter(1)
FM135
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Control Box (1)

rev 12-14-15 Mighty Mule 362-D Installation Instructions 5
Tools and Materials
Tools Needed:
• Power Drill
• Open End Wrenches — 1/2" and 9/16"
• Adjustable Wrench
•
3/8" Drill Bit
• Hacksaw or Heavy Duty Bolt Cutters
• Small Flat Bladed Screwdriver
• Large Phillips Screwdriver
• Tape Measure
• Level
• Wire Strippers
• C-Clamps — small, medium, and large
• Center Punch
• Hammer (for center punch)
• Extra person will be helpful
Materials You May Need for the Installation:
These items are NOT included with the gate opener kit. Some of these items can be purchased or special ordered
through Tractor Supply Co. Please see page 26 or www.mightymule.com.
• 12 VDC automotive/lawn tractor battery is required to power the opener. (Page 2)
• Low voltage wire [RB509] will be needed to run from the transformer to the opener control board; length
depends upon the distance between the transformer power supply and the control box. (Page 13 & 26)
• If your gate is more than 1000' away from an AC power source you will need to use at least one 10 watt Solar
Panel [FM123] to charge the 12 Volt battery. (Page 2 & 26)
• PVC conduit for protecting in ground wiring. (Page 6)
• Push-To-Open Brackets [FM148] are required if gates open out from property. Page 3 & 26)
• Materials to reinforce thin walled tube or panel gates. (Page 7)
• Depending on the type of gate, a horizontal cross member or mounting plate may be needed to mount the front
of the opener and gate bracket to the gate. (Page 3 & 7)
• Some installations may require muffler clamps for the gate bracket. (Page 7)
• (2)16 AWG crimp on fork lugs (Page 15)
• Surge protection for transformer. (Page 16)
• Weather proof outlet is required if transformer is plugged into outside outlet. (Page 16)
• Some types of installations require U-Bolts for closed position stop plate. (Page 11)
• A low profile ground stop is required for dual gates when using the Mighty Mule gate lock. (Page 11)

6Mighty Mule 362-D Installation Instructions rev 12-14-15
If the gate post is larger than
6" the Post Pivot Bracket can
be removed and the center
hole of the Post
Bracket can be the
mounting point
for the gate
opener.
Center hole of
post bracket
Installation Overview for Pull-To-Open Gates
PUSH-TO-OPEN installation instructions begin on page 19.
Example of an installation on a chain link fence:
IMPORTANT: To achieve the most efficient
leverage for the gate opener and ensure long
trouble free service, the gate opener needs to
be installed within the following parameters.
The diagram at left shows the optimum
position for gate opener arm in relation to
the gate in the open and closed positions.
Be sure the position of the gate opener and
brackets allows for 1" of clearance between
the gate and the opener in both the open and
closed position, at the same time maintaining
a maximum distance of 13" from the end of the
retracted opener arm to the gate bracket with
the gate in the closed position.
36' power cable allows the control
board to control the SECOND
gate opener (run in PVC conduit)
You will need to trench across the
driveway in order to lay conduit for
the second opener power cable.
120 Volt indoor
Transformer
(surge protector
not supplied)
Fence Post
Set in Concrete
Run 1000' (max.) of low
voltage wire to control box
from transformer
(wire not included).
PVC conduit (not included)
to protect wire from lawn
mowers and weed eaters.
Gate Swings Evenly and Freely
Hung Firmly and Plumb
Control Box
First Opener Second Opener
Closed Position Stop Plates
Gate Bracket
1" minimum
Gate in the
OPEN POSITION
Pinch Area
Gate in the
CLOSED POSITION
Pinch Area
1" minimum
13" or less

rev 12-14-15 Mighty Mule 362-D Installation Instructions 7
IMPORTANT: Determine which side of the driveway you will mount the control box. From this point on, the gate and
gate opener on the same side as the control box will be referred to as the FIRST gate and gate opener. The gate and
gate opener on the opposite side of the driveway from the control box will be referred to as the SECOND gate and gate
opener.
We recommend you position the opener near the centerline of the gate to keep the gate from twisting and flexing
and to avoid backsplash from rain water.
The Post Bracket Assembly
The position of the post bracket assembly
determines the leverage and efficiency of the
opener. The post bracket assembly position
also sets the clearance between the opener
and the gate in the open and closed positions.
The post bracket works well for
installations on round and square fence
posts. Because the post bracket carries the
entire thrust of the active opener, bolts must
completely penetrate the post.
On wood posts, place a metal plate or
washer (not supplied) between the nuts and
the post to prevent the thrust of the opener
from pulling the bolts and washers out of the
wood.
The post pivot bracket may not be necessary on posts larger than 6" in diameter (see page 6). Fence posts smaller
than 6" in diameter or 6" square should be made of metal instead of wood to remain stable while the opener is moving
the gate.
Reinforcing Gates for the Gate Brackets
We recommend using a muffler clamp, wood, or metal, to reinforce thin-walled tube gates, or wood to reinforce panel
gates as shown. These reinforcement methods will prevent damage to the opener and gate. Additional hardware may be
needed depending on the installation.
Muffler Clamp for
Gate Bracket
Wood or Metal
Reinforcement
1" x 6" Wood
Reinforcement
Post
Bracket
Post
Pivot Bracket
Metal Plate
Wooden Post
Post
Bracket
Post
Pivot Bracket
Metal Plate
Wooden Post
Post Pivot
Bracket
Post
Bracket
Post Bracket
Assembly
Thin Walled
Tube Gate
Gate Bracket
Muffler Clamp
(not supplied)
Gate Bracket
Wood or Metal
Reinforcement
(not supplied)
Gate
Bracket
Panel
Gate
1" x 6"
Wood
Reinforcement
Installation of the FIRST Gate Opener

8Mighty Mule 362-D Installation Instructions rev 12-14-15
Install Post Bracket Assembly and Gate Bracket
Step 1
Insert the 3/8" x 11/2" bolt through the center hole of the post brackets
and post pivot bracket. Secure with a 3/8" washer and 3/8" lock nut.
DO NOT overtighten the lock nut (the post pivot bracket will have to be
adjusted later).
Step 2
Attach post bracket assembly to the rear mount of the opener with a
clevis pin and a 3/8" washer. Secure the clevis pin with a hairpin clip.
Step 3
Attach gate bracket to the front mount of the opener with a clevis pin
and a 3/8" bushing. Secure the clevis pin with a hairpin clip.
Step 4
With the gate in the fully open position and the opener arm fully retracted, adjust the post bracket assembly and
gate bracket until the opener is level. While holding the opener level, use C-clamps to temporarily secure the post bracket
assembly and gate bracket to the post and gate.
3/8" x 11/2" Bolt
3/8" Lock Nut
Post Pivot Bracket
Post Bracket
Post Bracket Assembly
3/8" Washer
Clevis Pin
Hairpin Clip
Post Bracket Assembly
3/8” Washer
Rear Mount
Opener
Clevis
Pin
Hairpin Clip
Gate Bracket
Front Mount
Bushing
Fence Post
Gate in Open Position
Opener Arm Fully Retracted
LEVEL horizontal cross member
Post Bracket Assembly
Gate Bracket
Level Opener

rev 12-14-15 Mighty Mule 362-D Installation Instructions 9
Step 5
Be sure the position of the gate opener and
brackets allows for 1" of clearance between
the gate and the opener in both the open
and closed position, while at the same time
maintaining a maximum distance of 13"
from the end of the retracted opener arm to
the gate bracket with the gate in the closed
position. This mounting position will give the
opener the most efficient leverage point for
operation and provides the least possible
pinch area
Step 6
After verifying that you have the best position
for the post pivot bracket in the open position,
insert the 5/16" x 11/2" bolt through the
aligned holes of the post bracket and post
pivot bracket to hold it in place. Remove the
clevis pin from the front mount and while
supporting the gate opener, swing the gate
and gate opener to the closed position. Again,
check the clearance and be sure that the gate
opener is not binding at the post pivot bracket.
If you don't have the required clearance,
or if the gate opener is binding on the post
pivot bracket, remove the 5/16" x 11/2" bolt and
readjust the post pivot bracket.
TIP: Turn the post pivot bracket over for more
hole alignment options. You can also move the
entire post bracket assembly to different positions on the post.
Step 7
When the post bracket assembly is in the optimum position, reattach the opener to the gate bracket (gate in the open
position); recheck the gate opener level; make sure the brackets are clamped securely.
Step 8
Mark reference points for bolt holes on the post through middle of post bracket assembly slots. Mark reference points for
bolt holes on the gate cross member through middle of gate bracket slots. After marking your reference points, remove
the opener and brackets from the fence and gate.
1" minimum
Gate in the
OPEN POSITION
Pinch Area
Gate in the
CLOSED POSITION
Pinch Area
1" minimum
13" or less
Be sure gate opener
and bracket don't bind.
5/16" x 11/2"
Bolt
Post Pivot
Bracket
Determine Best
Hole Alignment
to Achieve
1" Clearance
Post Bracket
5/16" Lock Nut
5/16" Washer
Post Bracket
Assembly
Mark fence post through
middle of bracket slots
and drill 3/8" holes through
post.
Gate In Open Position
Arm Fully Retracted
LEVEL horizontal cross member
Mark cross member through middle of gate
bracket slots and drill 3/8" holes through cross member.

10 Mighty Mule 362-D Installation Instructions rev 12-14-15
Step 9
Drill 3/8" holes through post as marked. Fasten post bracket assembly
to the fence post using two 3/8" x 8" bolts, washers and lock nuts. You
must use bolts that completely penetrate the post.
Step 10
Drill 3/8" holes through the gate cross member as marked. Mount gate
bracket using two 3/8" x 2 3/4" bolts, washers, and lock nuts.
NOTE: After the gate opener installation is complete and operation
of the opener system has been tested, you should remove excess
bolt length extending beyond the tightened nuts with a hacksaw or bolt
cutters.
Round Tube & Chain Link Gate
Square Tube Gate
Mounting Plate
Created for
Decorative Gate
(required but not
supplied)
Remove excess bolt length
with hacksaw or bolt cutters
FRONT VIEW SIDE VIEW
FRONT VIEW
SIDE VIEW
Gate Bracket Mounting Examples
Round Metal Post
Round Wood Post
Square Metal Post
Square Wood Post
Remove excess bolt length
with hacksaw or bolt cutters
SIDE VIEW
TOP VIEW
EXAMPLES
Gate Bracket
Mounting
Examples
Attach Opener Arm
Step 1
Attach the opener
to the securely
bolted post bracket
assembly and gate
bracket using clevis
pins, bushings,
and hairpin clips, or
optional Pin Lock
[FM133] (page
26). Verify that the
opener is level and
adjust the post
bracket assembly, if
necessary.
Step 2
Install the SECOND gate opener and hardware on the second gate following the same procedures as the FIRST gate
opener and hardware ("Installing Post Bracket Assembly and Gate Bracket" Steps 1–10).
NOTE: The power cable for the Second Opener should be run in PVC conduit under the driveway to protect it from
damage due to lawnmowers, heavy equipment, etc. (See illustration on page 6.) NEVER SPLICE opener arm power
cables. This will cause performance problems and may damage the opener.
Level Opener
Gate In Open Position
LEVEL horizontal cross member
Post Bracket Assembly
bolted to fence post
Clevis Pin, Bushing, and Hairpin Clip
Clevis Pin, Washer, and Hairpin Clip
Gate Bracket bolted
to gate cross member
Fence Post