Mikro MK300 User manual

MK300 / MK300E Earth Leakage Relay User's Guide
A BRIEF OVERVIEW
1. DESCRIPTION
The MK300 and MK300E are microprocessor based numerical earth leakage relays designed to monitor the
leakage current in a electrical installation. With the use of microprocessor technology and digital signal processing
technique, the MK300 and MK300E relays are equiped with state-of-the-art digital hormonic filter to minimise
nuisance tripping.
The MK300 & MK300E relays can continuously display the leakage current on the front display panel. When the
relay trip as a result of a leakage being detected, the leakage current will be recorded. This recorded leakage
current and all the settings on the relay can be viewed at by pressing the RESET button on the relay
MK300E comes with two additonal remote control inputs. The additional inputs are remote test input and the
remote reset input. Other additional features of the MK300E include positive safety output contact and 50% pre-fault
contact.
2. LIGHT INDICATORS
The indicators display the status of the system as follow:
Table 1: System Status
a - Auxiliary power supply indicator
b - Relay trip status indicator
c - Time delay status indicator
d - Down key
e - Up key
f - Reset key
g - Test key
h - DP indicator
i - FUNCTION indicator
j - VALUE indicator
Symbols
I ∆n- Sensitivity setting
∆t - Time delay setting
Data- Previous tripped value
j
i
h
g
a
b
c
d
e
f
Indicator
Aux Trip Delay FUNC VL
0 0 0 0 0
1 0 0 0 1
1 B 0 X B
1 0 X 1 1
1 0 X B 1
1 0 1 X X
Status
Delay time lapsed and relay tripped
Scroll through setting.
Programming mode.
No auxiliary supply.
Normal condition, no tripping.
Leakage current exceeded set limit,
time delay coundown started.
1 = ON
0 = OFF
X  = don't care
B  = Blinking
VL  = VALUE
FUNC = FUNCTION

FUNC DP Value
off off Real-time leakage current.
1 blink Sensitivity setting.
2 blink Delay time setting.
3 off Previous tripped leakage current.
Message Description
'E Ct' Error in ZCT connection
'tESt' Replay tripped under test mode
'OFL' 'Overflow'. The measurement exceeded
the display range for the respective
sensitivity setting range.
Display range for sensitivity setting range
1: From 0.00A to 0.22A
Display range for sensitivity setting range
2: From 0.00A to 0.10A
Display range for sensitivity setting range
3: From 0.00A to 3.10A
Table 2: Function codes
Table 3: Display messages
3. PUSH-BUTTONS OPERATION
a) Trip test
Press the 'TEST' button to simulate a trip
condition
b) Trip reset
Press the 'RESET' button to reset the
relay when tripped
c) View setting
When the relay is not under tripped
condition, pressing the 'RESET' button
will scroll through the various functions of
the relay
Figure 1: Scroll sequence
d) Program setting
Only function codes 1 and 2 can be
programmed.
 Step 1: Press RESET key until the
  function digit shows required
function.
 Step 2: Press the UP and DOWN key
 simultaneously to enter
programming mode. The function
digit blinks to indicates the relay
is in programming mode
 Step 3: Use the UP or DOWN key to
select the desired value.
 Step 4: To save the selected value, press
the UP and DOWN key
simultaneously. This will exit the
programming mode with the
selected setting being saved.
To exit programming mode without saving the
selected setting, press the 'RESET' key once.
4. REMOTE CONTROL INPUTS *
a) Remote test input
This digital input is similar to the TEST
push-button. To remotely test the relay,
make a connection between terminals 4
and 6 of the relay.
b) Remote reset input
This digital input is to remotely reset the
relay when tripped. To reset the relay, make
a connection between terminals 4 and 5 of
the relay.
5. OUTPUT CONTACTS
a) Trip contact:
This is a latching type contact. It is
activated under following conditions :
- broken connection between the relay and
the ZCT
- leakage current exceeded the sensitivity
setting
b) 50% pre-fault contact *
- Activated when leakage current reaches
50% of the sensitivity setting
c) Safety contact *
- Activated when the auxiliary supply is
connected and the relay is functioning
normally
- De-activated when connection to the ZCT
from relay is interrupted or auxiliary supply
failure
FUNCTION 1 FUNCTION 2 FUNCTION 3off

6. TECHNICAL DATA
Models
MK300-5 & MK300E-5  : 50Hz
MK300-6 & MK300E-6  : 60Hz
Auxiliary Supply
Supply voltage     : 240 VAC +/- 10%
Rated frequency   : 50Hz / 60Hz
VA rating   : 3 VA typical
Setting
Sensitivity Adjustment  : Range 1 is stepping from 0.03A -> 0.05A -> 0.10A -> 0.15A
   Range 2 is from 0.20A to 0.75A in step of 0.05A
   Range 3 is from 0.80A to 3.00A in step of 0.05A
Delay Time Adjustment  : From 0.05 to 3.00 sec in step of 0.05 sec
   : From 3.00 to 10.0 sec in step of 0.50 sec
Remote Test / Reset Inputs : N.O. dry contact *
Output
Trip Contact:
Rated voltage   : 250 VAC
Continuous carry   : 6A (cosj = 1.0)
Make and carry for 0.2 s  : 30A
Safety Contact:
Rated voltage   : 250 VAC
Continuous carry   : 5A (cosj = 1.0)
Make and carry for 0.2 s  : 10A
50% Pre-fault Contact:
Rated voltage   : 250 VAC
Continuous carry   : 5A (cosj = 1.0)
Make and carry for 0.2 s  : 10A
Contact specification:
Contact arrangement  : change-over
Contact material   : Silver alloy
Operating time   : 15ms max.
Expected electrical life  : 100,000 operations at rated current
Expected mechanical life : 5 million operations
Approval    : UL / CSA, VDE, TUV, SEMKO
Indicators
Auxiliary supply : green color LED indicator
Time delay : red color LED indicator
Trip : 7-segment LED and red color LED indicator
Real-time leakage current : 7-segment LED
Mechanical
Mounting method : Panel mounting
Front panel : Standard DIN 96mm x 96mm
Approximate weight : ?.? kg

7. CONNECTION DIAGRAMS
 Typical Application Diagram for MK300
8. CASE DIMENSIONS
 Typical Application Diagram for MK300E
Remote Reset
Remote Test
TRIP
CONTACT SAFETY CONTACT
SAFETY
CONTACT
50% PRE-FAULT
CONTACT