Milestone KOS Series User manual

KOS
Rapid Microwave Labstation
Operator Manual
MM073-004 (June 2012)
MILESTONE
HELPING
PATIENTS

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 3 of 108
Thank you for having selected our system and welcome to the ever growing world club of users for Milestone
laboratory instrumentation.
We are sure that you will be completely satisfied with this new tool entering your laboratory.
We invite you to read carefully this operator manual and to keep it in reach for convenient and fast
consulting.
For any possible clarification or any request for assistance please contact either our Representative in your
country:
Or contact
Milestone s.r.l.
Via Fatebenefratelli, 1/5
24010 Sorisole (BG) Italy
Tel. +39.035.412 8264
Fax [phone]
web site www.milestonemedsrl.com
e-mail [e-mail]
Please read the user manual before using the device!

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 4 of 108
SUMMARY
SUMMARY ........................................................................................................................................................ 4
1. INTRODUCTION........................................................................................................................................ 6
1.1. Symbols used .................................................................................................................................... 6
1.2. Intended uses .................................................................................................................................... 7
1.3. Technical specifications..................................................................................................................... 7
1.3.1. Microwave unit........................................................................................................................... 7
1.3.2. Touch control terminal............................................................................................................... 8
1.3.3. GPR/K module........................................................................................................................... 8
1.4. Transport and storage conditions...................................................................................................... 8
1.5. Warning information........................................................................................................................... 9
1.6. Instrument labeling explanation....................................................................................................... 10
1.7. Compatible reagents........................................................................................................................ 10
1.8. Waste disposal of the equipment .................................................................................................... 11
1.9. Waste disposal of reagents ............................................................................................................. 11
2. SETTING UP THE INSTRUMENT........................................................................................................... 12
2.1. Introduction to KOS ......................................................................................................................... 12
2.2. Space requirements......................................................................................................................... 13
2.3. Unpacking and checking list............................................................................................................ 14
2.4. Final placement ............................................................................................................................... 15
2.4.1. Product overview ..................................................................................................................... 15
2.5. Fume extraction system................................................................................................................... 17
2.6. Power supply ................................................................................................................................... 18
2.7. Internet connection.......................................................................................................................... 19
2.7.1. How to start the Remote Assistance ....................................................................................... 21
2.8. Reagents.......................................................................................................................................... 22
2.9. Log IN and Log OUT........................................................................................................................ 23
2.10. Set date and time............................................................................................................................. 25
2.11. Set language.................................................................................................................................... 26
3. KOS HISTOMODULES AND ACCESSORIES ........................................................................................ 27
3.1. Histoprocessing (up to 3mm thickness)........................................................................................... 27
3.2. Antigen retrieval............................................................................................................................... 29
3.3. Decalcification and/or fixation.......................................................................................................... 32
3.4. Special stains................................................................................................................................... 37
3.5. GHM/K Gross hardening ................................................................................................................. 38
3.6. Summary table................................................................................................................................. 39
4. OPERATE WITH KOS.............................................................................................................................. 40
4.1. Touch control................................................................................................................................... 40
4.2. Run programs.................................................................................................................................. 41
4.2.1. Histoprocessing ....................................................................................................................... 41
4.2.2. Decalcification.......................................................................................................................... 47
4.2.3. Special stains........................................................................................................................... 50
4.2.4. Antigen retrieval....................................................................................................................... 52
4.2.5. Fixation .................................................................................................................................... 60
4.2.6. Gross hardening ...................................................................................................................... 61
4.3. Retrieving saved processing results................................................................................................ 62
4.3.1. How to delete a saved processing........................................................................................... 62
4.4. How to modify a program................................................................................................................. 63
4.5. Delete modified programs................................................................................................................ 66
4.6. Edit modified programs.................................................................................................................... 67
4.7. Create and modify favorite display.................................................................................................. 69
4.7.1. Delete from favorite list............................................................................................................ 70
4.8. Notes................................................................................................................................................ 71
4.9. Compliance...................................................................................................................................... 72
4.10. Help.................................................................................................................................................. 72
4.11. KOS system settings ....................................................................................................................... 73
4.11.1. Reagents management ........................................................................................................... 74
4.11.2. User management ................................................................................................................... 75
4.11.3. Owner Settings ........................................................................................................................ 77

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 5 of 108
4.11.4.
Remote Assistance.................................................................................................................. 78
5. REPORTING ............................................................................................................................................ 78
5.1. Export processing from the terminal to the USB ............................................................................. 78
5.2. Install the LogViewer ....................................................................................................................... 80
5.2.1. Open process........................................................................................................................... 80
5.2.2. Print process............................................................................................................................ 82
6. MAINTENANCE ....................................................................................................................................... 83
6.1. Introduction...................................................................................................................................... 83
6.2. After each run .................................................................................................................................. 83
6.2.1. Rack cleaning procedure......................................................................................................... 84
6.3. Weekly............................................................................................................................................. 85
6.4. Monthly ............................................................................................................................................ 85
6.5. Every six month ............................................................................................................................... 85
6.6. Yearly............................................................................................................................................... 86
7. TECHNICAL TROUBLESHOOTING........................................................................................................ 87
8. GOOD PROCESSING PRACTICE.......................................................................................................... 88
8.1. Specimens....................................................................................................................................... 88
8.2. Fixation ............................................................................................................................................ 88
8.3. Beware............................................................................................................................................. 89
8.4. Reagents.......................................................................................................................................... 90
8.5. Tissue processing selection guidelines ........................................................................................... 90
8.6. Bone decalcification guidelines........................................................................................................ 92
A. APPENDIX........................................................................................................................................... 93
A.1. MW tissue processing troubleshooting guide.................................................................................. 93
A.2. MW decalcification troubleshooting guide..................................................................................... 100
A.3. Summary........................................................................................................................................ 101
B. APPENDIX......................................................................................................................................... 102
B.1. How to manage samples while an alarm is occurring during histoprocessing.............................. 102

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 6 of 108
1. INTRODUCTION
1.1. Symbols used
An instruction accompanied by this symbol provides a cautionary statement:
WARNING. Failure to follow the instruction may endanger the USER or cause damage
to the instrument.
An instruction accompanied by this symbol provides a caution against electric shock.
Be sure to follow the instruction to prevent accidents resulting from electric shock.
Biohazard.
Surface at danger temperature (more than 70°C, 158° F) do not touch.
Potentially flammable.
Laser source Class II.
Acid.
Aquatic pollution.
CE logo: this instrument complies with European community directives.
IVD medical device according to 98/79/EC directive.
Please read carefully this instruction.
Please read SERVICE Manual (operation for SERVICE only).
WEEE European directive symbol (2002/96/EC).
Electric/electronic device do not throw out in the environment.

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 7 of 108
1.2. Intended uses
The Milestone KOS and its accessories have been engineered for laboratory use and can therefore
withstand the harshest laboratory conditions for continuous use in Histological sample preparation
procedures.
The instrument is intended for laboratory use (indoor use) only.
The KOS Unit is specifically designed to semi automatically execute these processes for histopathological
applications:
•Fixation, post-fixation
•Dehydration and clearing
•Paraffin WAX infiltration
•Antigen retrieval
•Special staining
•Decalcification
The Milestone KOS must be operated exclusively with the reagents listed in “Compatible reagents” chapter
1.7.
Any other use of the instrument is considered improper and may void the warranty
provided by the manufacturer.
1.3. Technical specifications
Working Temperature: 15°C–30°C (59°F–86°F)
Humidity (relative): up to 80%
Maximum altitude: 2000m
This unit is developed to comply with the CAP-College of American Pathologists checklist for microwave
instruments requirements.
1.3.1. Microwave unit
Microwave Power: Max 800 Watt.
Power Emission: The Power Emission (Pulse Width) is controlled by the KOS software. The
microwave power output is regulated in 10 Watt increments. Control of microwave
power is made by modification of the In and Out phase of the Magnetron.
Power supply: 230 V ~ 50 Hz, 8A (see table below)
230 V ~ 60 Hz, 8A (see table below)
115 V ~ 60 Hz , 15A (see table below)
For more detail refer to chapter 2.6.
VALID ONLY FOR KOS COMPLETE KIT (NOT FOR KOS BASIC):
SAFETY PACK
50
-
60
Hz CAMERA PACK
(according to voltage of the unit)
Reagents and Organic solvent detector sensor Analogic camera 50Hz (PAL model) and 60Hz
(NSTC model)
Humidity detection sensor Front panel 5.6" color camera monitor
MW leakage sensor
(included ALSO in KOS BASIC)

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 8 of 108
1.3.2. Touch control terminal
It is possible to operate the unit by simply touching the icons on the screen.
Characteristics: TK-WIN10CEi-TFT-LCD color display
Resolution 800x600 pixels, 8’’
Touch screen
Mass storage CF 256MB
RAM 256 MB
CPU 500MHz
Windows™ CE.NET 6.0
Programs: Multiple pre-stored programs, with customizable USER defined programs
I/O-Interface: 2x USB port 2.0, 1x LAN Ethernet 10/100 Mbps RJ-45
The two USB PORTS are located adjacent to the main power switch, on the back side of KOS unit.
1.3.3. GPR/K module
Characteristic: Maximum solution volume: 750 ml
Slide capacity: 40 slides max.
Over pressure safety valve: to release pressure at 2 bar (130-135ºC).
Maximum working Temperature: 120ºC
1.4. Transport and storage conditions
Temperature: -20°C (-4°F) up to +60°C (140°F)
Humidity: up to 50% (at 40°C – 104°F) non–condensin g
Before turning the KOS on (when coming from a storage room) please let the unit reach
working environmental conditions (at least half an hour).
The manufacturer reserves the right change and/or improve specifications without notice
and without incurring in obligation.
The manufacturer reserves the right change and/or improve specifications without notice
and without incurring in obligation.

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 9 of 108
1.5. Warning information
Should the equipment be used in different ways than those specified by the manufacturer, the warranty
provided by the manufacturer may be void.
Main power plugs are considered disconnecting device. Disconnect all plugs from the socket outlet before
assembling of the system, before connection of the accessories and before cleaning.
Equipment shall be connected to main a power socket outlet which is accessible and visible by the operator.
Equipment is provided with replaceable fuses, however their replacement is to be performed by properly
authorized service personnel. If the system is still not properly working, please contact the local authorized
and trained service representative of the manufacturer.
All parts of the equipment and all accessories shall be supplied only by the manufacturer.
DO NOT OPEN THE CHASSIS! Failure to follow the instruction in the documentation
might lead to a reduction of device safety. If the equipment is not working properly,
please contact your supplier or the manufacturer.
Do not remove the instrument, accessories, panels or cover. Only authorized and
qualified SERVICE personnel may repair the instrument and access the instrument’s
internal components.
It is important that normal standards for safety and good laboratory practices are
applied. Always use common sense and the best known practice when operating the
instrument. Failure to follow the instructions in the documentation might lead to a
reduction of device safety.
The Competent Authority owning the instrument has primary responsibility for
accident-free operation together with designated personnel who operates SERVICE
or repair it.
To avoid damage to the instrument, use only the reagents listed in section 1.7
Compatible Reagents. Failure to follow the instructions in the documentation might
lead to a reduction of device safety.
Use caution when handling hot, molten WAX.
METAL PARTS
Never introduce metal parts into the MAIN CAVITY.
High voltage discharges may cause uncontrolled increases of temperature, which
could damage the unit and result in incorrect tissue processing also. Failure to
follow the instructions in the documentation might lead to a reduction of device
safety.
Be careful: exhaust reagents are toxic and carcinogenic.
Handle with care and follow the local standard regulations.
Caution – laser radiation. Class II: if opening, do not fix the beam. When opening the
door, a laser beam appears to facilitate the correct positioning of the histomodule.

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 10 of 108
1.6. Instrument labeling explanation
Note only
for Canada: this
symbol indicates the compliance with the requirements of
CAN/CSA-C22.2 No. 61010-1, 2nd edition, including Amendment 1.
1.7. Compatible reagents
Fixatives
Dehydration
Clearing Decalcification Impregnation Other
Milestone
Finefix® Milestone JFC solution Ethylenediaminetetraacetic acid (EDTA) 20% WAX, Histology grade Saline solution
Formalin,
buffered or
unbuffered
Milestone
Prowave®
solution Formic acid 12% Histochemical
stain for
histology
Formalin
saline Ethanol Hcl 10% Sodium citrate 10 mM, pH 6.0
Isopropanol Tris/EDTA pH
9.0
Methanol
Industrial Methylated
Spirits
Please refer to chapter 8.4 for purity grade of reagents.
DO NOT USE REAGENTS DIFFERENT FROM THOSE LISTED ABOVE.
In case of doubts please contact: [e-mail].
R
eagents other than those listed above may damage some components of the instrument.
Do not use acetone, benzene or trichlorethane in the instrument!
Fixatives containing mercuric salts, acetic or picric acid will corrode metallic components
in the instrument and shorten instrument life.
If you choose to work with such fixatives, it is essential to perform a rack cleaning cycle
with multiple water rinses each time after use, to minimize damage.

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 11 of 108
1.8. Waste disposal of the equipment
This instrument is an in-vitro medical device and it is usually installed in a laboratory where specimens and
other biological tissues are present. For your safety, it is therefore required to clean and disinfect before
entering in contact with it. You must also wear gloves when operating with the system.
It is required in case of return that the unit is cleaned and disinfected before sending it back to Milestone s.r.l.
Non-disinfected devices will be no longer accepted and you will be contacted to get the relative disinfection
cost.
International health rules require that shipments of biohazard materials are not done in standard packages
(risk of sanctions).
It is recommended the use of enzymatic detergents and polyphenolic based disinfectants or chlorine
substitutes to clean and disinfect the instrument. In alternative, to decontaminate the instrument, the use of a
solution of 1:10 Bleach (recommended by the CDC for disinfecting) is also allowed.
For further information, please contact the manufacturer: [e-mail].
In addition, complying with directive 2002/96/EC of the European Parliament and of the Council of 27
January 2003 on waste electrical and electronic equipment (WEEE), the separate collection environmental
managed of equipment is mandatory.
It is necessary to return the used equipment to the distributor or to inquire about the presence of a local
empowered system for collection and disposal of WEEE.
The in-observance of Directive 2002/96/EC or of the local law which acknowledges it can have potential
effects on the environment and human health.
This symbol indicates separate collection
for electrical and electronic equipment
If additional requirements on accident prevention and environmental protection exist in the country of
operation, this instruction manual must be supplemented by appropriate instructions to ensure compliance to
such requirements.
1.9. Waste disposal of reagents
For further information please refer to the MSDS (Material Data Safety Sheet) provided by your supplier.
Do not remove the side panels of the unit during the cleaning operations.
Before doing any operation disconnect the power supply.
Do not use direct or high-pressure water to clean the instrument.
For safety reason, any operation without the individual protective devices must be
avoided.
Handle with care and store in a cold dry space using a tightly closed container.
Vapors may collect in empty containers. Treat empty containers as hazardous.
Waste material should be disposed of in an approved incinerator or in a designated landfill
site, in compliance with all federal, provincial and local government regulation.
Some reagents can have potential health effects and cause environmental pollution if not
correctly disposed.

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 12 of 108
2. SETTING UP THE INSTRUMENT
2.1. Introduction to KOS
The KOS is a unit provided with state-of-art microwave Hardware/Software, that allows obtaining consistent
and reproducible results in the histopathology laboratory, for high throughput tissue processing and other
histological applications.
The system and its accessories have been engineered for laboratory use and can therefore withstand the
harshest laboratory conditions for continuous use in Histological sample preparation procedures.
This manual refers to KOS, microwave Labstation and its application is suitable for NON vacuum processing
of tissue specimens with a maximum thickness of up to 3 mm.
The KOS concept
Microwave
Tissue
Processor
Specially
developed
Histomodules
A set of prestored
programs

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 13 of 108
Milestone KOS is a precision instrument that requires the utmost care when it is unpacked and installed.
The weight of KOS is approximately 40kg (88lb) at least 2 people should remove the
microwave unit from its box and locate it on the bench.
Provide a vibration free bench of at least 0.55m in width and 0.8m in depth, suitable for a weight of 50kg and
place the KOS on it.
Make sure the unit is not placed against any side surface limiting the air cooling inlet/exhaust: let at least a
distance of 10cm for each side.
Never install the KOS unit under a fume hood.
The presence of acids o
r caustic reagents may contaminate the air flow used for ventilating
the electronic components, exposing them to possible corrosion or shorting of circuits.
CONNECTING CABLES
Never
connect or remove cables when power to the unit is switched
on, to avoid risk of damage.
METAL PARTS
Never
introduce metal parts into the microwave chamber.
High voltage discharges may cause uncontrolled increases
in temperature, which could damage the unit.
CLEANING CAVITY AND DOOR
Periodically
inspect and clean cavity, door seals and
hinges. Do not use aggressive cleaning materials. If
microwave exposed surfaces are not kept clean, local “hot
Spots” are generated with possible corrosion of the metal
surface.
FOOD
Never
heat food in a microwave oven used for laboratory
procedures.
2.2. Space requirements
Unit dimensions:
UNIT
Width: 340mm (14in) Height: 550mm (22in) Depth: 530mm (21in)
CAVITY
Width: 240mm (10in) Height: 265mm (11in) Depth: 290mm (11.7in)
Space dimensions required to locate the unit:
Width: 970mm (38in) Height: 920mm (36in) Depth: 1090mm (43in)
NO

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 14 of 108
2.3. Unpacking and checking list
When unpacking, check that all parts correspond to the packing list included in the shipment. Utmost care
must be made during unpacking of KOS, to avoid scratching or damage of the external coating. Check if
your KOS (or KOS BASIC) part number corresponds to the voltage supply of the laboratory, please refer to
chapter 1.3.1.
KOS is delivered in a carton box (weight 50kg-110lb) with these dimensions:
Width 600mm (23.6in)
Height 900mm (35.4in)
Depth 800mm (31.5in)
A separate carton box (W480mm/19in-H100mm/4in-D480mm/19in) is positioned over the main carton box:
remove and keep it apart. This box contains accessories which will be used during the installation of the
KOS.
Lift the main carton box up to facilitate KOS removal.
The KOS comes protected by a plastic bag to prevent problems of moisture infiltration during transportation.
Then open the box (or boxes) with accessories (optional).
The KOS (or KOS BASIC) part number includes the following items:
1. Microwave unit complete with integrated Touch Control terminal
2. Power cord (x1)
3. Plastic hose + metal cable clamp
4. Operation Manual
5. USB Data Traveler
Accessories: Histomodules are supplied according to customer specific order (to be ordered apart).
POWER CORD
Ref. P/N 67109
(115V ~ 60Hz)
Ref. P/N 70304
(230V ~ 50/60 Hz)
PLASTIC HOSE and METAL
CABLE CLAMP
Ref. P/N 50332
Ref. P/N 64757
OPERATION MANUAL and
USB
MM0
73
Ref. P/N 62160

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 15 of 108
2.4. Final placement
Now KOS unit can be positioned in its final place of use. When the instrument is positioned, it must be firmly
placed. Make sure that the bench is level.
Insert the positioning plate in the KOS as shown below, with the mark TOP visible.
During the KOS SETUP the microwave unit should not be connected to the main power
supply.
2.4.1. Product overview
The picture below shows the front view of the KOS system.
Pull the handle towards the operator to open the door. On door opening, microwave emission is turned off by
4 safety mechanical switches.
An overview of the back side of KOS is shown in the following picture.
Main power
Switch &
USB ports
Door handle
Charcoal
filters
Terminal
& Cavity
monitor
Exhaust hose
connection
Power cord
connector
and fuses

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 16 of 108
The KOS has dedicated software, based on Windows CE (Microsoft Windows CE is a trademark of Microsoft
Corporation). Use the touch screen pen to select the desired menu function.
The picture below shows the internal cavity of the KOS.
The KOS is neither a kitchen type nor a commercially modified kitchen type microwave unit. It is a rugged,
heavy duty professional system, designed to guarantee many years of trouble free and safe operation.
0
1
3
4
6
7
9
,
-
INFRA-RED SENSOR
•Fully automatic non
contact temperature
control
•100% walk-away
operation
EXHA ST FAN
•No toxic vapors to
laboratory
•Extraction of
vapors to fume
hood
R
E
A
R
F
R
O
N
T
A TO START
MAGNETIC STIRRER
•Homogeneous
temperature
distribution within the
solution eliminating
“Hot Spots”
•All cassettes are
processed under the
same preset conditions
Touch screen
Terminal control
R
E
A
R
F
R
O
N
T

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 17 of 108
2.5. Fume extraction system
The instrument is equipped with carbon filters (Ref. P/N 67223) to avoid the releasing of fumes into the
laboratory environment. The carbon filter absorbs reagent fumes to prevent their diffusion into the laboratory
atmosphere. To ensure the filters are effectively operating, they must be periodically replaced (see chapter
6.5 for details).
The KOS is vented, according to CAP requirements, through the external exhaust outlet positioned on the
back of the instrument, with a hose dedicated to the external fume extraction system (if any).
In case of connection to an external fume extraction system, the customer is required to adapt the hose
connector. The plastic hose supplied has these characteristics:
•Length: 2.5m(98in)
•External diameter: 55mm(2.15in)
•Internal diameter: 50mm(2in)
Connect the black exhaust hose of 2.5m (Ref. P/N 50332) to the exhaust outlet located on the back panel of
the unit.
Use the metal cable clamp (Ref. P/N 64757) to fix the hose to the exhaust outlet connection. Use a screw
driver to tighten the metal cable clamp.
Now connect the other side of tube the fume extractor of the laboratory.
Either the carbon filters or an external fume extraction system must be properly installed
at all times, according to local regulations in force on laboratory safety.
The external fume extraction system must permit an air flux of 36m
3
/h
(cube meter per hour), (21cfm).

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 18 of 108
2.6. Power supply
Power supply line needs to have a ground connection (yellow/green, green or bare wire), do not use the
white wire (neutral of power line). Power supply neutral has to be referred to ground.
Power line protection: 115V: Miniature circuit breaker curve C, 15A, interruption more than 6000A.
230V: Miniature circuit breaker curve C, 16A, interruption more than 6000A.
Residual current device: 30mA (Class I device).
Check if Voltage and Frequency on the back label of the KOS correspond to the power
supply outlet in your laboratory.
POWER SUPPLY
KOS RED
KOS BLUE
KOS GREEN
R
ef. P/N
Ref. P/N
Ref. P/N
115 V ~ 60 Hz, 15A 67050/R 67050/B 67050/G
230 V ~ 50 Hz, 8A 67051/R 67051/B 67051/G
230 V ~ 60 Hz, 8A 67052/R 67052/B 67052/G
POWER SUPPLY
KOS BASIC RED
KOS BASIC BLUE
KOS BASIC GREEN
Ref. P/N
Ref. P/N
Ref. P/N
115 V ~ 60 Hz, 15A 67000/R 67000/B 67000/G
230 V ~ 50 Hz, 8A 67001/R 67001/B 67001/G
230 V ~ 60 Hz, 8A 67002/R 67002/B 67002/G
Milestone microwave
units must be connected to a grounded power supply to guarantee
the optimal performance of all the high voltage components.
The unit chassis and the following components must be connected to the electrical
ground to avoid any electromagnetic interference:
-High Voltage transformer
-Heating transformer
-Magnetron (microwaves generators)
-High Voltage diode and capacitors
-Microwaves diffuser
Milestone supplies the power cable, either for 115Vac or one for 230Vac, according to the
correct voltage of your country.
Both versions are provided with ground connection.
During the installation, our distributor will check the compatibility of our cable plugs with
the local electrical socket to guarantee the correct ground connection of the unit.
Now you can connect the power supply cable and switch the KOS ON, using the main power switch located
on the back side panel of the microwave unit.
KOS is now ready for use.

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 19 of 108
2.7. Internet connection
It is necessary to connect KOS to Internet to get Remote Assistance SERVICE.
IT IS NOT ADMIT
TED TO RUN PROGRAMS WITH KOS
WHILE
USING REMOTE
ASSISTANCE CONNECTION.
PROCESSES IN REMOTE ASSISTANCE ARE FOR TESTING USE ONLY,
NEVER PLACE SPECIMEN INSIDE KOS.
In order to access the remote assistance (as described in the chapter 4.11.4), following data are needed
from the Information Technology Department/Network ADMINISTRATOR of the laboratory:
- LAN connection with standard RJ45 Ethernet cable and connector
- Dedicated IP address and Subnet Mask (strongly preferred to DHCP SERVICE); only port 80 has to be
enabled without limitations
- LAN gateway and DNS server addresses
- At least 150kb/s real transfer rate (uploading and downloading).
When connecting KOS
to remote assistance, it is necessary that Firewall, traffic data
filters and all software are disabled. Milestone s.r.l. strongly suggests not to use the DHCP
SERVICE, but fix the IP address in order to properly set up the LAN defenders.
From Log-in screen click on ADMINISTRATOR and insert the password (issued as a separate document
inserted in the Operator Manual).
The Administrator HOME PAGE appears. Press SETTINGS to access the administrator screen and then
press “OWNER SETTINGS”.

Milestone s.r.l. MM073-004 – KOS – Operation Manual
Page 20 of 108
The following screen appears. Enter the data required supplied by the Network Administrator.
For example:
A keyboard appears when clicking on any white box; insert the number required and then press directly the
green arrowed check box (in the figure below). Fill all white boxes with data network.
Press SAVE to store data, as shown below on the left and the message on the right appears.
Press Ok and restart the Unit, as indicated in the figure above.
IP Address 192.168.1.200
Subnet Mask 255.255.255.0
DNS server address 192.168.1.6
Default Gateway add. 192.168.1.1