Mini Gadgets OmniXElectricalBox User manual

1 Version 1.3
OmniX Electrical Box Hidden
Camera
SKU: OmniXElectricalBox

2 Version 1.3
THANK YOU FOR PURCHASING THE
OMNIXELECTRICALBOX HIDDEN CAMERA
Please read this manual before operating the camera
and keep it handy.
Your purchase should include:
1 x OmniXElectricalBox
1 x 16GB MicroSD Card
1 x MicroSD Card Reader
4 x Batteries
1 x Wall Charger
1 x Manual
1 x A/V Cable
1 x Remote
1 x Battery Charger

3 Version 1.3
GET FAMILIAR WITH YOUR OMNIXELECTRICBOX
HIDDEN CAMERA

4 Version 1.3
HOW TO CHARGE THE BATTERY
1. Pull out the batteries.
2. Insert batteries into the supplied charger.
3. Connect the supplied charger to a wall outlet.
4. The chargers LED screen will look like the below
when charging is completely done.

5 Version 1.3

6 Version 1.3
IMPORTANT WARRANY INFORMATION: If the
warranty sticker on your device has been removed or
tampered with, your lifetime warranty will be voided.
You may be charged fees or denied a return should this
happen.
OPERATING THE CAMERA
Note: If you are not located in the US, or if you intend
to use this product anywhere other than the US, you
will need to purchase a converter in order to use the AC
wall plug in and avoid damaging the product. Because
different countries use different voltages in their
electrical wiring, you will need a converter that adapts
to the current in your particular country.
HOW TO TURN ON THE CAMERA
1. Point the remote at the device and press the
power button on the remote. The Green light
will blink once and then the Red light will blink
3 more times and turn off (if motion is detected
immediately). The device is now in motion
detection mode.

7 Version 1.3
NOTE: If the light doesn’t come on, try many different
angles when pressing the power button and pointing it
at the front/top of the unit. Do not hold down the power
button. Press and release the button only.
2. To put the device into standby mode, stop
motion recording by pressing the motion
detection button one time. The Green light will
come on and the device will be in standby
mode.
HOW TO RECORD VIDEO
1. When the camera is in Standby Mode, press the
“Continuous Recording Mode” button (see
page 5). The Indicator LED will flash two times.
2. Once the Indicator LED turns off, the camera is
now recording video.
HOW TO STOP RECORDING VIDEO

8 Version 1.3
1. While the camera is recording video, press the
“Continuous Recording Mode” button once
more. (The Indicator LED will turn on.)
2. The camera has stopped recording and is now
in Standby Mode.
HOW TO TAKE PICTURES
1. When the camera is in Standby Mode, press the
“Photo Button” (see page 5). The green light
will turn red while the photo is being taken.
2. Once the photo is taken, the light will turn back
to green and once again be in standby mode.
HOW TO RECORD MOTION DETECTION
1. When the camera is in Standby Mode press the
“Motion Detection” button (see page 5).
2. If motion is detected, the Red light will flash 2
times and turn off.
3. If there is no motion after 1 minute, the device
will return to detection standby mode until
motion is detected again. While waiting, the
Green light will be on.

9 Version 1.3
NOTE: If you activate motion detection and there is no
motion currently in front of the camera, there will be no
indication you have entered into motion mode. The green
light will simply remain on. If you wish to confirm that
you have entered into motion detection mode, wave your
hand in front of the camera lens. The unit will flash the
red light 2 times, then the light will turn off confirming
that the device detected your motion and is now
recording video.
HOW TO STOP RECORDING MOTION DETECTION
1. While the camera is recording motion
detection, press the “Motion Detection” button
once more. (The Indicator LED will turn on.)
2. The camera has stopped recording motion
detection and is now in Standby Mode.
HOW TO USE PIR SENSOR (If Applicable)
Note: The “Motion Detection” mode and “PIR” mode
work similarly in that they detect motion. The “Motion
Detection” mode relies on the camera itself to detect

10 Version 1.3
motion, while the “PIR” mode relies on the PIR sensors
to detect motion. “PIR” represents “passive infrared
sensor”, which relies on measures of infrared light to
detect motion.
Note: Only OmniX Products have a PIR sensor installed.
OmniEye products do not come with this feature.
1. When the camera is in Standby Mode, press the
“PIR” button on the remote (see page 5).
2. The LED will flash Red 3 times and turn off.
3. The unit is now in PIR Mode and is waiting for
motion. When motion is detected, the light will
turn green, then red, and blink 3 times and turn
out. The unit is now recording.
4. To return to standby mode, press the PIR
button again. The light will return green to
indicate the unit is in standby mode.
CHANGING YOUR DEVICE SETTINGS (INCLUDING THE
DATE/TIME STAMP)
Your OmniXElectricalBox comes with an A/V cable that
is used to connect the device to a monitor/TV so that