MINN KOTA EDGE User manual

EDGE
PONTOON TROLLING MOTOR
CE MASTER USER MANUAL

Model: ______________________________________________________________
Serial Number: _______________________________________________________
Purchase Date:________________________________________________________
Store Where Purchased: ________________________________________________
NOTE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair
or replace this unit. You may obtain service by: calling Minn Kota at [phone] or returning
your motor to the Minn Kota Factory Service Center; sending or taking your motor to any Minn Kota
authorized service center on enclosed list.
Please include proof of purchase, serial number and purchase date for warranty service with any of the
above options.
Please thoroughly read this user manual. Follow all instructions and heed all safety and cautionary
notices below. Use of this motor is only permitted for persons that have read and understood these
user instructions. Minors may use this motor only under adult supervision.
ATTENTION: Never run the motor outside the water, as this may result in injuries from the rotating
propeller. Connect motor to battery only if motor is in operating position and the speed-control is in
the zero position. Remove power supply from motor before tilting motor up and propeller out of the
water. When connecting the power-supply cables of the motor to the battery take care that they are
not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before
using the motor make sure that the insulation of the power cables in not damaged. Disregarding these
safety precautions may result in electric shorts of battery(s) and/or motor. Always disconnect motor
from battery(s) before cleaning or checking the propeller. Avoid submerging the complete motor as
water may enter the lower unit through control head and shaft. If the motor is used while water is
present in the lower unit an electric short will occur and considerable damage to the motor will be the
consequence. This damage will not be covered by warranty.
CAUTION: Take care that neither you nor other persons approach the turning propeller too closely,
neither with body parts nor with objects. The motor is powerful and may endanger or injure you or
others. While the motor is running watch out for persons swimming and for floating objects. Persons
whose ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or other
substances are not permitted to use this motor. This motor is not suitable for use in strong currents.
The constant noise pressure level of the motor during use is less than 70dB(A). The overall vibration
level does not exceed 2,5m/sec2.

minnkotamotors.com
Features ................................................................................ 4
Mount Installation ................................................................. 5
Attention .............................................................................. 6
Caution ................................................................................. 7
Using Your Edge ................................................................... 8
Battery & Wiring Installation ...............................................10
Motor Wiring Diagram ........................................................14
Service and Maintenance ......................................................15
Frequently Asked Questions .................................................17
Troubleshooting ...................................................................19
Parts Diagram.......................................................................20
Parts List .............................................................................22
Warranty .............................................................................24
Compliance Statement .........................................................26
TABLE OF CONTENTS

4
FEATURES
Specifications subject to change without notice.
Tilt Twist Tiller™ Handle
Adjustable
Depth Collar
Steering
Tension Knob
Mounting Bracket
Lifetime Warranty
Flexible Composite Shaft
Propeller
Permanent Magnet,
Cool Power™Motor

minnkotamotors.com 5
We recommend that you have another person help with this procedure.
1. Place the mount and motor in position on the deck of the boat.
• We recommend that the motor be mounted as close to the boats
centerline as possible
• Make sure the bow area under the chosen location is clear and
unobstructed for drilling
• Make sure the mount is positioned far enough beyond the edge of the boat.
The motor, as it is lowered into the water or raised into the boat, must not
encounter any obstructions.
2. Once in position, mark a minimum of four of the six mounting holes.
Drill through the marked holes using a 9/32 drill bit.
Note: The four front mounting holes uses the same bolt pattern as used
on Minn Kota quick release plates MKA-21, RTA-17, MKA-16-02 and
MKA-32. The pontoon mount may be attached to any of these for your
mounting convenience.
3. Mount the plate to the bow through the drilled holes using the 1/4”-20 x 2” bolts,
washers and nuts provided.
MOUNT INSTALLATION

6
• Avoid running your motor with the propeller outside of the water.
This may result in injuries from the rotating propeller.
• It is recommended to set the speed selector to zero and place the motor
in the deployed position prior to connecting power cables. Disconnect
power cables prior to stowing.
• Always ensure that the power cables are not twisted or kinked; and that
they are securely routed to avoid a safety or trip hazard. Ensure cables are
unobstructed in all locations to avoid damaging the wire insulation. Damage
to the insulation could result in failure or injury.
• Always inspect the insulation of the power cables prior to use to ensure
they are not damaged.
• Disregarding these safety precautions may result in an electrical short of
the battery(s) and/or motor. Always disconnect the motor from the
battery(s) before cleaning or checking the propeller.
• Avoid submerging the complete motor as water may enter the lower unit
through control head and shaft. Water in the lower unit may cause an
electrical short and damage the lower unit. This damage will not be covered
by warranty.
ATTENTION

minnkotamotors.com 7
• Always operate the motor a safe distance away from obstructions. Never
approach the motor when the propeller is running. Contact with a spinning
propeller may endanger you or others.
• Always exercise safe practices when using your motor; stay clear of other
watercrafts, swimmers, and any floating objects. Always obey water
regulations applicable to your area of operation.
• Never operate the motor while under the influence of alcohol, drugs,
medication, or other substances which may impair your ability to safely
operate equipment.
• This motor is not suitable for use in strong currents exceeding the thrust
level of the motor.
• The constant noise pressure level of the motor during use is less than
70dB(A). The overall vibration level does not exceed 2,5m/sec≈.
CAUTION!

8
Tilt Twist Tiller
These motors offer a choice of five forward and three reverse speeds.
The speed control may be operated in either direction, forward or reverse. Turn the
tilt twist tiller handler counterclockwise from O (off) to increase reverse speed and
clockwise from O (off) to increase forward speed. Thrust decreases as you approach O
from either direction.
The twist grip tiller handle is shipped in
the down position. Firmly pull the handle
up to the horizontal position. The handle
has five available positions: 45° down,
horizontal, 15°, 30° and 45° tilted
up. The handle locks in the horizontal
position, but can be tilted down by
pushing the release button located on
the left underside of the handle pivot.
USING YOUR EDGE
Handle Controls Off/On, Steering
and Forward/Reverse
Release Button

minnkotamotors.com 9
Depth Adjustment
• Firmly grasp the outer shaft or
control head and hold it steady.
• Loosen depth setting knob until
the shaft slides freely.
• Raise or lower the motor to the
desired depth.
• Turn the motor control head to
the desired position.
• Tighten depth setting knob to
secure the motor in place.
Note: When setting the depth be sure
the top of the motor is submerged at
least 12” to avoid churning or agitation
of surface water. The propeller must be
completely submerged.
Steering Adjustment
• Adjust steering tension knob to provide enough tension to allow the motor
to turn freely, yet remain in any position without being held or; Tighten
the knob and lock the motor in a preset position to leave your hands free
for fishing.
Depth
Setting
Knob
Steering
Tension
Knob
12”
Minimum
Depth

10
Boat Rigging & Product Installation:
For safety and compliance reasons, we recommend that you follow American Boat and
Yacht Council (ABYC) standards when rigging your boat. Altering boat wiring should
be completed by a qualified marine technician. The following specifications are for
general guidelines only:
!CAUTION!: These guidelines apply to general rigging to support your Minn Kota
Motor. Powering multiple motors or additional electrical devices from the same power
circuit may impact the recommended conductor gauge and circuit breaker size. If you
are using wire longer than that provided with your unit, follow the conductor gauge
and circuit breaker sizing table below. If your total conductor length is more than 50
feet we recommend that you contact a qualified marine technician.
An over-current protection device (circuit breaker or fuse) must be used. Coast Guard
requirements dictate that each ungrounded current-carrying conductor must be
protected by a manually reset, trip-free circuit breaker or fuse. The type (voltage and
current rating) of the fuse or circuit breaker must be sized accordingly to the trolling
motor used. The table below gives recommended guidelines for circuit breaker sizing.
Conductor Gauge and Circuit Breaker Sizing Table
Total Conductor Length (length of all conductors in the total circuit)
Motor Thrust Circuit Breaker 10 feet 20 feet 30 feet 40 feet 50 feet
40#, 45# 50 Amp @ 12 VDC 10 AWG 8 AWG 6 AWG 4 AWG 4 AWG
50#, 55# 60 Amp @ 12 VDC 8 AWG 6 AWG 4 AWG 4 AWG 2 AWG
70# 50 Amp @ 24 VDC 10 AWG 10 AWG 8 AWG 8 AWG 6 AWG
*The conductor and circuit breaker sizing table above is only valid for the following assumptions.
1. No more than 3 conductors are bundled together inside of a sheath or conduit
BATTERY & WIRING INSTALLATION

minnkotamotors.com 11
outside of engine spaces.
2. Each conductor has 105°C temp rated insulation.
3. No more than 5% voltage drop allowed at full motor power based on published
product power requirements.
Reference:
United States Code of Federal Regulations: 33 CFR 183 – Boats and Associated Equipment
ABYC E-11: AC and DC Electrical Systems on Boats
Selecting the Correct Batteries
The motor will operate with any deep cycle marine 12 volt battery/batteries. For
best results use a deep cycle, marine battery with at least a 115 ampere hour rating.
As a general on the water estimate, your 12 volt motor will draw one ampere per
hour and your 24 volt motor will draw .75 ampere per hour for each pound of thrust
produced when the motor is running on high. The actual ampere draw is subject
to your particular environmental conditions and operation requirements. Maintain
battery at full charge. Proper care will ensure having battery power when you need
it, and will significantly improve the battery life. Failure to recharge lead-acid batteries
(within 12-24 hours) is the leading cause of premature battery failure. Use a variable
rate charger to avoid overcharging. If you are using a crank battery to start a gasoline
outboard, we recommend that you use a separate deep cycle marine battery/
batteries for your Minn Kota trolling motor.

12
BATTERY & WIRING INSTALLATION
Advice Regarding Batteries:
Never connect the (+) and the (–) terminals of the battery together. Take care
that no metal object can fall onto the battery and short the terminals. This would
immediately lead to a short and utmost fire danger.
Recommendation:
Use battery boxes and covered battery terminal clamps like Minn Kota accessory
#MK-BC-1.
How to Connect the Batteries
12 Volt Systems:
1. Make sure that the motor is switched off (speed selector on “0”).
2. Connect positive ( + ) red lead to positive ( + ) battery terminal.
3. Connect negative ( – ) black lead to negative ( – ) battery terminal.
4. For safety reasons do not switch the motor on until the propeller is in the water.
24 Volt Systems:
1. Make sure that the motor is switched off (speed selector on “0”).
2. Two 12 volt batteries are required.
3. The batteries must be wired in series, only as directed in wiring diagram,
to provide 24 volts.
a. Connect a connector cable to the positive ( + ) terminal of battery 1 and
to the negative ( – ) terminal of battery 2.
b. Connect positive ( + ) red lead to positive ( + ) terminal on battery 2.
c. Connect negative ( – ) black lead to negative ( – ) terminal of battery 1.

minnkotamotors.com 13
4. For safety reasons do not switch the motor on until the propeller is in the water. If
installing a leadwire plug, observe proper polarity and follow instructions in your
boat owner’s manual. See wiring diagram on following pages.
!CAUTION!
• IMPROPER WIRING OF 24/36 VOLT SYSTEMS COULD CAUSE
BATTERY EXPLOSION!
• KEEP LEADWIRE WING NUT CONNECTION TIGHT AND SOLID TO
BATTERY TERMINALS.
• LOCATE BATTERY IN A VENTILATED COMPARTMENT.

14
THIS IS A UNIVERSAL MULTI-VOLTAGE DIAGRAM. DOUBLE CHECK YOUR
MOTORS VOLTAGE FOR PROPER CONNECTIONS.
Over-Current Protection Devices not shown in illustrations.
MOTOR WIRING DIAGRAM
_
FIVE SPEED SWITCH
INTERRUPTEUR A CING VITESSES
12v
24v

minnkotamotors.com 15
Propeller Replacement
!CAUTION!: DISCONNECT THE MOTOR FROM THE BATTERY BEFORE
BEGINNING ANY PROP WORK OR MAINTENANCE.
1. Disconnect the motor from all sources of power prior to changing the propeller.
2. Hold the propeller and loosen the prop nut with a pliers or a wrench.
3. Remove the prop nut and washer. If the drive pin is sheared or broken, you will
need to hold the shaft steady with a blade screwdriver pressed into the slot on
the end of the shaft.
4. Turn the old prop to horizontal (as illustrated) and pull it straight off. If drive pin
falls out, push it back in.
5. Align the new propeller with the drive pin.
6. Install the prop washer and prop nut.
7. Tighten the prop nut 1/4 turn past snug [25-35 inch lbs.] Do not over tighten
as this can damage the prop.
SERVICE & MAINTENANCE
Weedless Propeller
Prop Nut
Washer
Drive Pin
Slot End

16
SERVICE & MAINTENANCE
General Maintenance
1. After use, the entire motor should be rinsed with freshwater, then wiped down
with a cloth dampened with an aqueous based silicone spray such as Armor All®.
This series of motors is not equipped for salt water exposure.
2. The propeller must be inspected and cleaned from weeds and fishing line after
every 20 hours of operation. Fishing line and weeds can get behind the prop,
damage the seals and allow water to enter the motor.
3. Verify the prop nut is secure each time the motor is used.
4. To prevent accidental damage during transportation or storage, disconnect the
battery whenever the motor is off of the water. For prolonged storage, lightly
coat all metal parts with an aqueous based silicone spray.
5. For maximum battery life recharge the battery(s) as soon as possible after use.
For maximum motor performance restore battery to full charge prior to use.
6. Keep battery terminals clean with fine sandpaper or emery cloth.
7. The propeller is designed to provide weed free operation with very high
efficiency. To maintain this top performance, the leading edge of the blades
must be kept smooth. If they are rough or nicked from use, restore to smooth
by sanding with fine sandpaper.

minnkotamotors.com 17
Can I get replacement parts for my Minn Kota trolling motor?
Yes, we would be glad to help you with this. Please contact us for replacement parts
in the U.S.A. at 1 800 227 6433. In Canada, call 1 800 263 6390.
Can my freshwater Minn Kota trolling motor be used in saltwater?
We designed a special line of motors for use in salt or brackish water. The Minn Kota
Riptide trolling motors have a number of “saltwater-engineered” enhancements,
including stainless steel hardware, sealed electrical connections and an advanced
painting process for improved corrosion protection. Using any of our standard Minn
Kota motors in saltwater may dramatically reduce the life of the motor and voids
manufacturer’s warranty. To extend the life of your Minn Kota Riptide saltwater trolling
motor, thoroughly rinse the motor with freshwater after every use in saltwater and store
indoors. Never leave the motor submerged in saltwater when the boat is moored.
What about shaft length selection?
Choosing the correct shaft length is important so that the angler’s electric motor does
not cavitate, creating fish-spooking noise. The rule of thumb is that the center of the
motor section should be submerged 9”. In general, shaft length selection is more critical
with bow-mount motors versus transom-mount motors. Most boat transoms are similar
in their distance to the water, and Minn Kota’s standard transom shaft lengths should be
adequate. With bow-mounted motors, there is much greater variation in shaft length
requirements. Measure down from the mounting surface of the transom or bow to
the water level. Add 5” to waterline measurement for fishing in rough water. Add 12”
to waterline measurement for steering a hand control motor while standing. Use this
measurement and the tables below to find the appropriate shaft length.
FREQUENTLY ASKED QUESTIONS

18
FREQUENTLY ASKED QUESTIONS
What are the benefits of a bow-mounted electric motor?
Boats do not tend to go in a straight line. Because of this, it is much easier to pull a boat
than to push a boat. It is also easier to move the bow of the boat sideways compared
to moving the transom. Therefore, a bow-mounted electric motor allows for much
greater boat control and positioning. If quick-response boat control and positioning is
what you are looking for, a Minn Kota bow-mount electric motor is a must.
Will the CoPilot work with my cable steer or hand control
trolling motor?
No, CoPilot is designed only for electric steer motors.

minnkotamotors.com 19
1. Motor fails to run or lacks power:
• Check battery connections for proper polarity.
• Make sure terminals are clean and corrosion free. Use fine sandpaper
or emery cloth to clean terminals.
• Check battery water level. Add water if needed.
• Check propeller for line or weeds.
2. Motor loses power after a short running time:
• Check battery charge, if low, restore to full charge.
3. Motor is difficult to steer:
• Loosen the steering tension knob on the bracket.
• Lubricate the composite shaft.
4. You experience prop vibration during normal operation:
• Remove and rotate the prop 180°. See removal instructions in prop section.
NOTE: For all other malfunctions, see enclosed authorized service center listing for
nearest service center.
TROUBLESHOOTING

20
This page provides Minn Kota®WEEE compliance disassembly
instructions. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased. Tools required, but not limited to: Flat Head screw driver, Phillips screw driver, socket set, pliers, wire cutters.
PONTOON 55/HC 55 LBS THRUST 12 VOLT 52” SHAFT
PARTS DIAGRAM
24
22
25 26
27
5
13 10
17
3
2
1
4
16
7
68
9
19
15
14
18
21
11
12
20
95
92
93
90
89
82
81
80
85
86
79
94
87
76
77
91
88
96
84
83
31
28
29
52
55
53
48
34
50
49
54
56
62