RED M+
BLACK M-
CONTROL BOARD/
CARTE DE COMMANDE
RED
WHITE
FOOT PEDAL
CONTROL BOARD
STEERING MOTOR
BATTERY GAUGE
BATTERY 1 BATTERY 2
BLACK B-
RED B+
COIL CORD
MOTOR
RED M+
BLACK M-
BLACK
COMPASS
SENSOR
BOARD
BATTERY 1
RT 80 ST is 24-volts only!
BATTERY 1 BATTERY 2 BATTERY 3
BLACK
AUTOPILOT INDICATOR, RED
SYSTEM READY INDICATOR, GREEN
REED SWITCH
AUTO PILOT INDICATOR, RED
(EQUIPPED MOTORS ONLY)
MOMENTARY / CONSTANT
INDICATOR, GREEN
ACCESSORY PLUG
SPEED ADJUSTMENT KNOB
AUTOPILOT ON EQUIPPED MOTORS ONLY
ACCESSORY PLUG
ACCESSORY PLUG
SYSTEM FEATURES
CoPilot for Terrova setup and use instructions
•YourmotorisfactoryinstalledwithCoPilotforTerrova.
•WirelesscontrolforTerrova.
•Plug–n–playdesignallowsforeasyhook-up.
•Functionsincludesteering(right/left),prop(on/off),AutoPilot(on/off),highspeedbypass,andspeedcontrol.
•ReceivermountsintotherightsideplateoftheTerrovamotorforseamlessinstallation.
•Patentedremoteallowsmotortobecontrolledfromrod,wrist,belt,orboatconsole.
•Quick-releaserodmountsallowquickandeasytransferofremotefromrodtorod.
•CopilotTerrovacanbeusedwithorwithoutthecordedfootpedal.
•RemotewillnotinterferewithAutopilotorUniversalSonarOperation.
•Upto10remotescanbeusedinterchangeablywiththesamereceiver.
•Componentsareenvironmentallysealedtoprotectagainstrain,wind,orsnow.
Installing the rod mount
•Therodmountisdesignedforinstallationonanyareaoftherodgrip,especiallytheareaforwardofthereel.(Seethefigures
above.)
•Spinningreelusersmaywanttoinstallthemountonthetopoftherodtoallowthumboperationoftheremote.
•Baitcastingreeluserswho“palm”thereelmayinstallthemountonthesideoftherodtoallowremoteoperationwiththeindexor
middle finger.
•Themountshouldbepositionedontherodsothattheunlockinglatchonthebracketistowardtherodtip.
1). Position the rod mount in the desired location on the fishing rod, holding it in place with your thumb.
2). Insert (2) tie-down straps through the rod mount and cinch down around the rod (place the locking head of the tie-down
strap to either side of the rod mount; do not place in the area below the remote.)
3). Trim the excess tie down strap with a side cutter or scissors.
•Toattachtheremotetothemount,slidetheremoteintothemountfromtherearofthebracket. Ensurethattheslidesonthe
mount engage the slots on the sides of the remote. Slide the remote into the mount until it snaps into the locked position.
•Toreleasetheremotefromthemount,pressdownontheunlockinglatchwhilesimultaneouslyslidingtheremoteoutofthe
mount.
•Duringperiodsofnon-use,werecommendthattheremotebeinsertedintothemountwiththebuttonsfacingdown.Thiswillhelp
to ensure that there are no unintentional button presses while the rod is in storage.
Using the nylon strap with the remote
For a general purpose strap mount, refer to the figure above. This strap can be used as a wrist mount, around the belt, to a fixed
location on the boat, etc…
SPINNING REEL
BOBINE ROTATIVE
BAIT CASTING REEL
BOBINE À JETER L’APPÂT
IN
ENTRÉE
OUT
SORTIE
