Mitel SmarT-1 EuroRoute Installation guide

8346-382-115-BA
Issue 1, January 1999
© Copyright 1999 Mitel Inc. All rights reserved.
® Registered Trademark of MITEL Corporation
™ Trademark of MITEL Corporation
Installation & Programming Guide
Compact Dialer

2 - Com
p
act Dialer 8346-382-115-B
Issue 1, January 1999
NOTICE
The information contained in this document is believed to be
accurate in all respects but is not warranted by Mitel Corporation
(MITEL). The information is subject to change without notice and
should not be construed in any way as a commitment by Mitel or
any of its affiliates or subsidiaries. Mitel and its affiliates and
subsidiaries assume no responsibility for any errors or omissions
in this document. Revisions of this document or new editions of it
may be issued to incorporate such changes.

Table of Contents
8346-382-115-B
Issue 1
,
Januar
y
1999 Com
p
act Dialer - 3
Compact Dialer Register Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
General Notes on Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
System and Trunk Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Route Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Programming Access Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Search Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Wall Mounting Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table of Contents
8346-382-115-BA
4 - Com
p
act Dialer Issue 1
,
Januar
y
1999

8346-382-115-BA
Issue 1, January 1999 Compact Dialer - 5
Section
REGISTER DEFAULT DESCRIPTION PAGE
System/Trunk
01 3 On-hook Timing 21
02 8 Rotary Inter-digit Pause 21
03 4 Inter-digit Time-out 21
04 4MF4Rate 22
05 0 ExchangeType 22
06 0 SubscriberType 22
08 0 Off-hook Beep 22
09 D Centrex Digit 23
Route Registers
20 Blank Route 1 Digit String 25
21 Blank Route 2 Digit String 26
22 Blank Route 3 Digit String 26
23 Blank Route 4 Digit String 26
24 20 Route 1 Dialling Rule 27
25 Blank Route 2 Dialling Rule 27
26 Blank Route 3 Dialling Rule 27
27 Blank Route 4 Dialling Rule 27
28 Blank System String 1 28
29 Blank System String 2 28
30 Blank System String 3 28
31 Blank System String 4 28
Programming Access
32 #345✳Local MF4 Password 29
33 #124✳Remote MF4 Password 29
SearchTables
01 Blank Search Table A, Set 1 31
02 Blank Search Table A, Set 2 31
03 Blank Search Table A, Set 3 31
04 Blank Search Table A, Set 4 31
05 Blank Search Table A, Set 5 31
06 Blank Search Table A, Set 6 31
07 Blank Search Table A, Set 7 31
08 Blank Search Table A, Set 8 31
09 Blank Search Table A, Set 9 31
0✳
✳✳
✳Blank Search Table A, Set 10 31
0# Blank Search Table A, Set 11 31
0A Blank Search Table A, Set 12 31
0B Blank Search Table A, Set 13 31
0C Blank Search Table A, Set 14 31
0D Blank Search Table A, Set 15 31
1 Compact Dialer Register Index

Compact Dialer Register Index
8346-382-115-BA
6 - Com
p
act Dialer Issue 1
,
Januar
y
1999
REGISTER DEFAULT DESCRIPTION PAGE
11 Blank Search Table B, Set 1 31
12 Blank Search Table B, Set 2 31
13 Blank Search Table B, Set 3 31
14 Blank Search Table B, Set 4 31
15 Blank Search Table B, Set 5 31
16 Blank Search Table B, Set 6 31
17 Blank Search Table B, Set 7 31
18 Blank Search Table B, Set 8 31
19 Blank Search Table B, Set 9 31
1✳
✳✳
✳Blank Search Table B, Set 10 31
1# Blank Search Table B, Set 1 31
1A Blank Search Table B, Set 12 31
1B Blank Search Table B, Set 13 31
1C Blank Search Table B, Set 14 31
1D Blank Search Table B, Set 15 31
Features
72 Blank Call Home Number 18
73 Blank Set Time/Date 18
74 Blank Call Home Time/Date 19
Commands
75 Not Applicable Clear Search Tables 19
76 Not Applicable Clear Default Route Strings (20 - 33) 19
81 Not Applicable Display Software Revision 19
82 Not Applicable Display Serial Number 19
83 Not Applicable Display Call Home Number 19
85 Not Applicable Display Search Tables 19
88 Not Applicable Drop from Program Mode 20
92 Not Applicable Enter Verify Mode 20
93 Not Applicable Re-load Defaults 20
95 Not Applicable Reset Statistics 20
96 Not Applicable Display Statistics 20
97 Not Applicable Leave Verify Mode 20
98 Not Applicable Exit Program Mode 20
✳
✳✳
✳#✳
✳✳
✳#Not Applicable Personal PIN Entry 28

8346-382-115-BA
Issue 1, January 1999 Compact Dialer - 7
Section

Indicates the Default for the register
 Represents a burst of 400 Hertz tone transmitted over the phone to the
subscriber.
Absorbed Digits Absorbed digits are digits that are “absorbed” by the Compact Dialer via
the Search Tables. The digits that are “absorbed” are copied to a special
buffer, which can hold a maximum of 8 digits. The absorbed digits can be
totally removed from the destination number or appended to, via the
respective Dialing Rule token.
Centrex Abusinesstelephoneservice provided bythe PSTNthatgives thesubscriber
unique telephone features, similar to the features provided bya PABX.
Destination Number The destination number isthe number thatisdialled to reach thecalledparty.
Exchange Line The physical connection between a telephone service subscriber and the
PSTN that provides the telephone service.
Hz Hertz
mA milliampere
MF4 Dialling MF4 tone dialling
ms millisecond
PABX Private Automatic Branch Exchange
pps pulses per second
PSTN Public SwitchedTelephone Network
Rotary Dialling Pulse dialling
Route A Route is a set of preprogrammed dialling rules that can include access
codes to be used to place a telephone call over a particular service or carrier.
A Route is chosen by matching dialled digits with a template in the Search
Tables.
Search Tables The Search Tables consist of two buffers, Buffer A and Buffer B, in which
the user’s dialled digits are screened for the purpose of assigned a pre-
defined setof instructions. It is here inthe Search Tables where calls can be
barred or sent to a select carrier via a Dialling Rule.
sec second
2 Glossary of Terms

Glossary of Terms
8346-382-115-BA
8 - Com
p
act Dialer Issue 1
,
Januar
y
1999

8346-382-115-BA
Issue 1, January 1999 Compact Dialer - 9
Section
Description
The Compact Dialer package consists of:
• 1 Unit
• 1 Safety Instructional Sheet
• 2 Line Cords (one for the network and one for the telephone).
Mounting
The Compactcan be placedon a deskor any other flatsurface or mounted vertically using
self tapping screws. Avoid placing the Compact in areas where severe temperature exists,
such as direct air flow from a heating duct, radiator or direct sunlight. This productis not
intended for outdoor use.
The installer, resident, may use the supplied template (refer to page 39) as a guide to drill
holes in the wall with a 3mmdrill. Beforemounting the Compact to a wall, the installer
can supply two 18mm #6 pan-headscrews and placetheminto pre-made holes in the wall.
When attaching the Compact to a plaster wall, insert the nylon anchors into the pre-made
holesapplyingthe 18mm #6 pan-head screws. The illustration below shows the positioning
of the Compact.
Connecting the Compact to your phone line
• Verify that the two cables supplied with your Compact are connected. If they are
not connected, please refer to the section titled, Installing the Compact Connection
Leads.
• Unplug your telephone from the BT WallSocket.
Note: If you have multiple extensions plugged into the Master BT Socket, then
route all of them through the Compact. You will be able to make calls from any of
the connected extensions, and they will be routed correctly. Extensions hard-wired
into the back of the BT socket will NOT be routed through the Compact.
• Plug the lead from the Compact Dialer with the BT plug connected into your BT
wall socket.
• Connect your telephone(s) to the lead with the BT telephone socket on the
Compact.
• Pick up the telephone handset, and verify whether you have dial tone.
• Replace the handset.
3 Hardware Installation

Hardware Installation
8346-382-115-BA
10 - Com
p
act Dialer Issue 1
,
Januar
y
1999
Checking whether the Compact will work on your line
• Pick up the telephone handset and dial 0002.
• If you hear a continuous tone you may hang up. The Compact will now call the
management centre for programming. Please wait 10 minutes before using your
telephone.
• If you do NOT hear a tone or you get a BT recorded message, you will need to
contact your maintainer to obtain a power supply.
Warning
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations.
• Use caution when installing or modifying telephone lines.
Connecting a Power Supply
• Connect the power supply to the power supply jack.
• Plug the power supply into a power outlet, and verify that the Mains switch is on.
• Lift the telephone handset, and check for dial tone.
• Repeat the installation process with the power supply connected.
• If you experience problems, please call your maintainer.
Note: Before disconnecting the power supply, in installations requiring a power supply,
disconnect the telephone network connections first.
Power Failure
If a power failure occurs while the optional power supply is being used, theuser’s
telephone equipment will be connected directly to the Exchange line. The user will still
have accessto thetelephone network,but the Compact will notscreenor route calls.This
statement does notapply to the installationsthat donotrequire the optional power supply.
Note: Although this equipmentcan use either loop disconnect or DTMF signalling, only
the performance of DTMF signalling is subject to regulatory requirements for correct
operation. It is therefore strongly recommended that the equipment is set to DTMF
signalling for access to public or private emergency services. DTMF signalling also
provides faster call set up.

Hardware Installation
8346-382-115-B
Issue 1
,
Januar
y
1999 Com
p
act Dialer - 11
Installing the Compact Connection Leads
There are two cables supplied with the Compact. One cable has a BT plug on one end;
the other end, a BT socket. Using these two cables, follow the listed steps to install your
Compact.
• Looking at the Compact, you will see three connectors; two of which are used to
connect the supplied cables.
• Connect the cable with the BT socket to the middle connector on the Compact.
This connector is identified on the back of the unit as, “To Telephones”.
• Connect the cable with the BT plug to the end connector on the Compact. This
connector is identified on the back of the unit as, “To Phone Socket”.
• Unplug your telephone from the BT wall socket.
• Plug your telephone into the cable on the Compact with the BT socket.
• Plug the Compact BT plug into your BT wall socket.
Safety Optional power supply
TheCompactDialeroperatesfroma nominal230+/-10%VACsupply. Thepowersupply
unitusedwiththisapparatusmustbefullycompliantwiththeEECLowVoltageDirective
(73/23/EEC).
Safety Status of Ports
PSU TNV †
NTP Ports TNV †
† TNV is defined in EN 60950: 1992.
Connectivity
TheCompact is intended tobeplacedin between the telephone wall outletand theuser’
telephone. There are two telecom cables, an RJ11 to BS6312 (BT) type plug for
connection to the Exchange and an RJ11 to BS6312 (BT) type socket for connection to
the resident’s telephone or answering machine, that are used to connect the unit.
Plug the cable from the wall here
Plug the cable with BT socket here,
Power Supply Connector
then connect your telephone to the socket

Hardware Installation
8346-382-115-BA
12 - Com
p
act Dialer Issue 1
,
Januar
y
1999
Basic Hardware Description
Mechanical Description
TheCompactconsists ofa plasticcase,enclosedcircuitryandan optional outboardpower
supply.
Electrical Description
The electrical characteristics are provided in the table below.
Safety Instructions
INSTRUCTIONS The exclamation point within an equilateral triangle is intended to alert the user to the
presence ofimportantoperatingand maintenance (servicing) instructions in the literature
accompanying the product.
Failure to follow all instructions may result in improper equipment operation and/or the
risk of electrical shock.
1. All installation personnel should consult the following information before
attempting to install this product.
2. Read all instructions before attempting to install or use this product.
3. Install and configure this product with only the assemblies specified in this guide.
4. Never install telephone wiring during a lightning storm.
5. Never install telephone jacks in wet locations.
6. Never touch telephone wires of terminals unless the telephone line has been
disconnected at the network interface.
7. Use caution when installing or modifying the telephone lines.
8. The AC power socket/outlet should be installed near the equipment and should be
easily accessible.
MECHANICAL
Weight:
Main Unit - 250g
Power Supply - 150g
Dimensions:
Main Unit - 30 x 90 x 130mm
Power Supply - 50 x 55 x 65mm
Mounting:
Flush wall mount or desk mount
ELECTRICAL
Power:
12 Volts @ 50 mA
Connections:
Standard RJ11 and power connector

Hardware Installation
8346-382-115-B
Issue 1,January1999 Compact Dialer- 13
Hardware SpecificationsRinger Impedance15k min
Ringing Sensitivity(25 Hz):25VAC min
Off-hook Current17.5 mA min,50 mA max
Battery Feed
OpenCircuit 12VDCnominal
Constant Current13mAmin, 13.5 mAmax
Short Circuit Current 13.5mAmax
MF4Receiver
Level-22 dBm min, +3max composite
Twist-6min + 6 maxcomposite dB
Time betweentones 40 ms min
RotaryReceiver (Rate) 8 min,12 max (pps)
MF4 Sender
LevelsdBV(ZR) VFL=-13 dBm +/- 2.5 dB
VFH= -11 dBm +/- 2.5 dB
Duration (programmable)70 ms min
RotarySender 10 pps, 33/66ms
AC Operating Range
AC Line 230/240VAC, +/- 10%, 50 Hz,
50 mA Max
Temperature0º to 45ºC
Humidity0% to 85%,non condensing
Holdover20 ms typical
Jacks DC Power 2.5mm
Equipment 142646501RC S/CCable 6P
PlugtoBTType Socket
142647501RC S/CCable 6P
PlugtoBTTypePlug
Regulatory Conformity
Safety EN60950
EmissionsEN55022,ClassB
Immunity EN50082-1
Network NTR3

Hardware Installation
8346-382-115-BA
14 - Com
p
act Dialer Issue 1
,
Januar
y
1999

8346-382-115-BA
Issue 1, January 1999 Compact Dialer - 15
Section
Acknowledgment Tones for Local Programming
While programming the Dialer with an MF4 telephone, you will hear tones that indicate
correct entries, incorrect entries and programming time-outs.In general, after each correct
entry, the Dialer will respond with two tones.
If You Hear

 means that thecommand you have enteredhas beenrecognized asbeingvalid(correct),
i.e. you entered #345✳.
If You Hear


means thatthe entry you have made has been accepted. This occurs after a parameter
has received all the digits it needs to complete programming, or if you have entered D on
a variable length parameter.For example: if you dial03 you will hear
 , if you then dial
6 you will hear

.
If You Hear

 means you have made an incorrect programming entry.
Notes: In the event of an invalid entry, wait for the four tones to stop and then retry the
entry. No data will be accepted by the Dialer for an incorrect programming entry.
Ifyou remain inactive for twenty-five seconds whileinprogramming mode,the unit will
exit from programming mode and revert to the previous program.
Acknowledgment Tones for Remote Programming
While remotely programming the Dialer with anMF4 telephone, you will hear tones that
indicate correct entries, incorrect entries and programming time-outs. In general, after
each correct entry, the Dialer will respond with an MF4 “D”.
If You Hear “A”
A meansthat the commandyouhave entered hasbeen recognized as beingvalid (correct),
i.e. you entered 29.
If You Hear “D”
Dmeans that the entry you have made has been accepted. This occurs after a parameter
has received all the digits it needs to complete programming, or if you have entered D on
a variablelength parameter. For example: if you dial03 you will hearA, if you then dial
6 you will hear D.
If You Hear “C”
Cmeans you have made an incorrect programming entry.
Ifyou remain inactive for twenty-five seconds whileinprogramming mode,the unit will
exit from programming mode, without saving any changes that were made.
Terminating Variable Length Entries
To terminate a variable length entry (SearchTables, Dialing Rules, Route Digit Strings
and Digit Strings) use an MF4 D.
4 General Notes on Programming

General Notes on Programming
8346-382-115-BA
16 - Com
p
act Dialer Issue 1
,
Januar
y
1999
Local Programming With a Fourth Column MF4Telephone
MF4 tones can be used to program the Compact Dialer. The default local programming
code is #345✳. To exitprogrammingmode and save data,wait for long toneto end, then
hang-up (go on-hook), dial 98.
To program the Compact Dialer locally:
• Go off-hook
• Enter #345✳(Contents of Register 32 by default)
• The Compact Dialer will respond with a long period of 400 Hz tone followed by 
• Once the beep is heard, local programming mode is entered.
Notes: Each time that the line cord is disconnected from the Dialer’s BT socket, labeled “To
Phone Socket”, and then reapplied,thedialerwillattempt to call the management system
by using the number stored in register72 (refer to page 18) for programming.
Because of the fact that variable length registers need to be terminated with the MF4
digit D, Mitel recommends that the Compact Dialer be programmed with a 4th column
telephone (A phone with a key pad including the buttons A, B, C and D).
Remote Programming With a Fourth Column MF4Telephone
The Compact Dialer can be programmed remotely by using MF4 tones. The default
remote programming code is #124✳. To exit programming mode and save data, dial
98
and hang up the remote telephone.
Note: Because of the fact that variable length registers need to be terminated with the MF4
digit D, Mitel recommends that the Compact Dialer be programmed with a 4th column
telephone (A phone with a key pad including the buttons A, B, C and D).
Call Home on Installation
One minute after the Compact is installed, the unit will call the carrier’s CallHome Well
Management Center (CHWMC), using the following process. The unit willgo off-hook
and dial the phone number (refer to Register72 on page 18) to the CHWMC. The unit
will then wait for a response from the CHWMC for a period of twenty-five seconds.
If noresponse is received from the CHWMC, the unitwill go on-hook and re-attempt to
Call Home after one minute. The unit will then wait for a response from the CHWMC
for a period of twenty-five seconds.
If no response is received after the second attempt, the Dialer will wait for one hour
before re-attempting to Call Home. The unit will then wait for a response from the
CHWMC for a period of twenty-five seconds.
If the third attempt is unsuccessful, the Dialer will Call Home every 24 hours, until the
Dialer receives a responsefrom the CHWMC.If the unit receives a password withinthe
twenty-five second period, it will respond by sending an MF4 D tone to the CHWMC.
If the unit receives an invalid password, it will disconnect. Otherwise, the unit will then
remain in view mode, where it will be ready to echo programming information or be
ready to be changed to program mode.
If a telephone goes off-hook during the Call Home process, the unit will stop the Call
Home process. The line will be reset, and dial tone will be returned to the user, allowing
the user to process a call. The Call Home process may take from two to three minutes,
depending on the size of the program. Ifanyoneenters programmodeand then exits from
programmode usingthe command98, the CallHomeprocess will be cleared.Theprocess
will not begin again, unless the Call Home WellTimefeature is programmed. Call Home
may be defeated by not programming a Call Home number.
Initialisation
Initialisation is a procedure that is used for re-loading the factory defaults into the
Compact.ThisprocedurewillnotaffecttheCallHomenumberthat is storedinregister72.
To initialise a Compact that is connected to an Exchange line:
• With the telephone device on-hook, press and hold the✳key located on the device
• While continuing to hold the✳key, take the telephone device off-hook
• Continue to hold the ✳key for 10 seconds
• Release the ✳key and listen for a 400 HZ tone followed by a 
• Dial 93 and listen for a 
• Dial 98 and listen for a 400 HZ tone followed by a “click” sound; hang up.

General Notes on Programming
8346-382-115-B
Issue 1
,
Januar
y
1999 Com
p
act Dialer - 17
Call HomeWell
Call Home Well will occur when the programmed time and date stored in Register 74
(Alarm register for Call Home) is reached. The unit will go off-hook and dial the phone
number (refer to Register 72 on page 18) to the CHWMC. The unit will then wait for a
response from the CHWMC for a period of twenty-five seconds.
Ifno response is received from the CHWMC, theunit willgo on-hook and re-attemptto
Call Home after one minute. The unit will then wait for a response from the CHWMC
for a period of twenty-five seconds.
If no response is received after the second attempt, the Dialer will wait for one hour
before re-attempting to Call Home. The unit will then wait for a response from the
CHWMC for a period of twenty-five seconds.
If the third attempt is unsuccessful, the Dialer will Call Home every 24 hours, until the
Dialer receivesa response from the CHWMC.Ifthe unit receives a password withinthe
twenty-five second period, it will respond by sending an MF4 D tone to the CHWMC.
If the unit receives an invalid password, it will disconnect. Otherwise, the unit will then
remain in view mode, where it will be ready to echo programming information or be
ready to be changed to program mode.
If a telephone goes off-hook during the Call Home process, the unit will stop the Call
Home process.Theline will bereset,anddialtone willbereturned to the user, allowing
the user to process a call. The Call Home process may take from two to three minutes,
depending on the sizeof the program.If anyone enters programmode and thenexits from
program mode usingthecommand98, the Call Homeprocess will be cleared.Theprocess
will not begin again, unless the Call Home Well feature is programmed.
Forced Call Home
Forced Call Home is accomplished by a technician going off-hook and dialling 0001.
Afterthisnumber isdialled,the unit will begin processingtheCallHome,whilereturning
a 400 Hz tone to the user.The intention of this tone is to advise the user to hang up. The
unit will then wait for a response from the CHWMC for a periodof twenty-five seconds.
If the attempt to Call Home is unsuccessful, the Dialer will not re-attempt to Call Home.
If the unit receives a password within the twenty-five second period, it will respond by
sending anMF4 D tone to the CHWMC. The unit will then remainin view mode, where
it will beready to echo programming information or be ready to be changed to program
mode.
If a telephone goes off-hook during the Call Home process, the unit will stop the Call
Home process.Theline will bereset,anddialtone willbereturned to the user, allowing
the user to process a call. The Call Home process may take from two to three minutes,
depending on the sizeof the program.If anyone enters programmode and thenexits from
program mode usingthecommand98, the Call Homeprocess will be cleared.Theprocess
will not begin again, unless the Call Home Well feature is programmed.
System String 2
Theuserofthe CompactDialer may programa number inSystem String 2without having
to enter into master programming mode by entering the code ✳
✳✳
✳#✳
✳✳
✳#. After this code is
entered, the user will hear a single beep. The dialer will then expect a 10 digit Personal
Identification Number. Once this number is entered, the dialer will respond with one
beep, and hang up. The user may then replace the handset. Please refer to page 28.
Features
These featuresare usedforthe CallHome feature.You must be intheprogramming mode
to use these commands.
Commands Definition
72
73
74
Program Call Home Number
Set Date/Time
Set Call Home date/time (8 digits)

General Notes on Programming
8346-382-115-BA
18 - Com
p
act Dialer Issue 1
,
Januar
y
1999
Commands
Special Function Commands allow access to specific data in the Compact Dialer. You
must be in the programming mode to use these commands.
Program Call Home Number—72
When thecommand 72 is entered, a  will be heard.The Compact Dialer will thenexpect
a Call Home number, up to 30 digits, to be entered. An MF4 Dmust then be entered in
order for the entry to be accepted. The Compact Dialer will return  , indicating that
the entry was accepted. This feature is not affected by the commands 93, 88 or 98.
For example, touse the phone number01291431181as the Call Home Number,the entry
would appear in the following format:
7201291431181D.
Call Homecan be disabledby entering an MF4Dafter the command72.Theentrywould
appear in the following format:
72D.
Set Date/Time—73
When thecommand 73 is entered, a  will be heard.The Compact Dialer will thenexpect
a desired time in atwenty-fourhour format anddate to be enteredin the following format:
MM(Month)DD(Day)HH(Hour)mm(Minute).
Following the minute digits (mm), the Compact Dialer will return  , indicating that
the entry was accepted. The data is saved upon entry. This feature is not affected by the
commands 93, 88 or 98.
For example, to set the time/date to July 21 at 10:35 PM, the entry would appear in the
following format:
7307212235.
Commands Definition
75
76
81
82
83
85
88
92
93
95
96
97
98
Clear Search Tables
Clear default Route string (20-33)
Display software revision
Display Serial Number
Display Call Home Number
Display Search Tables
Drop from Program Mode
Enter Verify Mode
Re-load Defaults
Reset Statistics
Display Statistics
Exit Verify Mode
Exit Programming Mode

General Notes on Programming
8346-382-115-B
Issue 1
,
Januar
y
1999 Com
p
act Dialer - 19
Call Home Date/Time—74
When the command74is entered, a  will beheard.The CompactDialerwill then expect
a desired Call Home time and date to be entered in the following format:
MM(Month)DD(Day)HH(Hour)mm(Minute).
Following the minute digits (mm), the Compact Dialer will return  , indicating that
the entry was accepted. The data is saved upon entry. This feature is not affected by the
commands 93, 88 or 98.
For example, to set the Call Home time/date to August 8 at 4:00 PM, the entry would
appear inthe following format:
7408081600.
Clear Search Tables—75
When the command 75 is entered, a  will be heard, indicating that the Search Tables
are cleared.
Clear Default Route Strings—76
When the command76 is entered, a  will be heard, indicating that the Default Route
Strings (20 - 33) have been erased, and that the factory default for Register 24 (20) has
been re-loaded.
Display Software Revision—81
When the command81 isentered,a  will be echoed tothePSTN side, and theCompact
Dialer will echo the software revision of the unit being accessed in the following format:
04519945.
Display Serial Number—82
When the command82 isentered,a  will be echoed tothePSTN side, and theCompact
Dialer will echo the eight-digit serial number of the unit being accessed in the following
format:
A12345678D.
Display Call Home Number—83
When the command 83 is entered remotely, a  will be echoed to the remote end, and
the Compact Dialer will echo the call home number of the unit being accessed in the
following format:
08000123456.
Display Search Tables—85
When the command 85 is entered, a  will be heard, and the contents of the Search
Tables, if any exist, will be echoed in the format of the following example:
06123456000000000211000000000000.
The first digit represents table A (0)or B (1). The second digit represents the number of
digitstoscreen(1throughF,representing1 through 15†).Thenextsixteendigitsrepresent
the digits to screen. The next seven digits represent action codes. The last seven digits
are reserved for future use. Refer to page 31 for more information on the Search Tables.
† 1=1, 2=2, 3=3, 4=4, 5=5, 6=6, 7=7,8=8,9=9,✳=10, #=11, A=12, B=13, C=14,D=15
(Where A, B, C, & D are Fourth Column tones)

General Notes on Programming
8346-382-115-BA
20 - Com
p
act Dialer Issue 1
,
Januar
y
1999
Drop from Program Mode—88
When the command 88 is entered, a  will be heard, followed by a click sound. The
Compact Dialer will then connect the user with the subscriber side without saving any
changes that were made to the program during the current programming session. This
command does not affect registers 72, 73, or 74.
Enter Verify Mode—92
When the command 92 is entered, a  will be echoed to the remote end, and the Compact
Dialer will echo the contents of any register that is entered.
Re-load Defaults—93
Whenthe command 93isentered,a  will beheard followed by  . The Compact Dialer
will re-load the factory defaults after the first  and remain in programming mode after
the second  .
Theseries of  may be heard as three consecutive tones, depending on the length of time
that the dialer takes to load the factory defaults.
Reset Statistics—95
When the command 95 is entered either, a  will be heard. The Compact Dialer will
then reset the statistical counters to a value of 00000000000000000000.
Display Statistics—96
When the command 96 is entered, a  will be echoed to the remote end, and the Compact
Dialer willecho, in Hex, any statisticalinformation that has been logged, in the following
twenty-digit format:
00010002000300041000.
The first four digits represent Route 1. The next four digits represent Route 2. The next
four digits represent Route 3. Thenext four digits represent Route 4. The last four digits
are reserved for future use.
For example, if the first four digits are 20A1, then this number would represent 8353
calls. If the next four digits are 0020, then this number would represent 32 calls.
Exit Verify Mode—97
When the command 97 is entered, a  will be echoed to the remote end, and the Compact
Dialer will exit verify mode and enter into programming mode.
Exit Programming Mode—98
When the command 98 is entered locally, a long  is heard, followed by a click sound;
remotely, a  will be heard, followed by a click sound. The user must wait until the
Dialer clicks before hanging up the telephone device. The click should beheard
within ten seconds.The Compact Dialer will then cut through the subscriber side to the
Exchange side, saving any changes that were made to the program during the current
programming session.