Cisco EX60 User manual

78-19809-03 EX60 Installation Guide | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
Cisco TelePresence System EX60
installation guide

Lift the rectangular box out of the
package.
In the box you will find the cables,
and another box with the touch
screen and handset.
Unpack the touch screen with the
handset and handset base.
Handset
Handset
base
Touch
screen
1Unpacking the touch screen and cables
Cables
EX60 is delivered with:
• EX60 unit
• Touch screen with cable
• Handset base with cable
• Handset
• AC adapter and power cable
• DVI-D to DVI-I cable
(recommended for optimal PC
image quality)
• VGA to DVI-I cable
• Stereo audio cable 3.5mm
• Ethernet cable
• Screwdriver
• Cleaning cloth
User documentation
User guides and compliance and safety information for this product
are available at the Cisco web site: http://www.cisco.com/go/ex-docs

2Unpacking the EX60 unit
Lay the package flat on the floor.
Pull the EX60, surrounded by foam
protection, out of the package.
Carefully loosen the foam protection.
Lift the EX60 and place it on a firm surface.
Weight: 7 kg / 15lb
EX60

BFasten the two units together. The screws
are pre–mounted in the handset base.
Use the screwdriver and fasten the screws at the
handset base from the underneath.
AHold the touch screen and the handset
base in an upright position.
Move the two units together. Make sure the
connector on the handset base slides into the
corresponding hole on the touch screen.
CConnect the cable between the handset and the handset base; then place the handset on the base.
3Optional: Mounting the handset
Tool: Screwdriver
EMC Class A declaration
This is a class A product. In
a domestic environment this
product may cause radio
interference in which case the
user may be required to take
adequate measures.
声明
此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING: This is a class A product. In a domestic environment
this product may cause radio interference in which case the user
may be required to take adequate measures.
Touch
screen
Handset
base

4System overview and basic setup
Kensington
lock
USB
Micro-
phone
Remove the cover
to get access to the
connectors at the
rear side.
Local area
network (LAN)
Touch screen
Power supply
(use the supplied
AC adapter)
Optional PC
video input
Optional PC
audio input
For maintenance only
(requires purpose-built
cable)
Optional LAN
connection
for PC
Headset
Connect the touch screen,
LAN and power as illustrated.
To connect a PC, see more
details in step 5.
You may connect an
external microphone and
a headset to your system
(not provided).

Audio and video input from PC
Connect the audio and video cables from the PC.
We recomemend using the DVI-D to DVI-I video
cable for optimal PC image quality.
The cables are in the rectangular box, see
illustration in step 1.
Optional LAN connection for PC
If you have a single LAN wall outlet only, you
may connect your PC to the second RJ45
socket of the EX60 (labelled with a PC symbol).
Your PC and the EX60 will then share the LAN
connection.
5Connecting a PC
Optional LAN
connection
for PC, RJ45
PC video input,
DVI-I cable
PC audio input,
Stereo cable
3.5 mm mini jack
Power button
• Tap the power button once to switch
on/off the monitor.
• Press gently and hold the power button
to shut down the system.
Camera
• Turn to open/close the
privacy cover.
• Tilt downwards to use
as document camera.
Camera LED
Power LED
6Starting the system
Please read the user documentation,
which is available on the Cisco web
site, for further information about how
to set up and use your system.