Mitel Navigator 3300 ICP Quick start guide

MITEL – SIP CoE
Technical
Configuration Notes
Configure the 3300 ICP for use with
Avaya SES
SIP CoE 10-4940-00111

ii
NOTICE
The information contained in this document is believed to be accurate in all respects but
is not warranted by Mitel Networks™ Corporation (MITEL
®
). The information is subject to
change without notice and should not be construed in any way as a commitment by Mitel
or any of its affiliates or subsidiaries. Mitel and its affiliates and subsidiaries assume no
responsibility for any errors or omissions in this document. Revisions of this document or
new editions of it may be issued to incorporate such changes.
No part of this document can be reproduced or transmitted in any form or by any means -
electronic or mechanical - for any purpose without written permission from Mitel Networks
Corporation.
TRADEMARKS
Mitel is a trademark of Mitel Networks Corporation.
Windows and Microsoft are trademarks of Microsoft Corporation.
Other product names mentioned in this document may be trademarks of their respective
companies and are hereby acknowledged.
Mitel Technical Configuration Notes – Configure the 3300 ICP for use with Avaya SES
March 2010, 10-4940-00111
®,™ Trademark of Mitel Networks Corporation
© Copyright 2010, Mitel Networks Corporation
All rights reserved

Table of Contents
iii
OVERVIEW ............................................................................................................... 1
Interop History....................................................................................................................1
Interop Status ....................................................................................................................1
Software & Hardware Setup...............................................................................................1
CONFIGURATION NOTES ....................................................................................... 2
3300 Configuration Notes ..................................................................................................2
Network Requirements.................................................................................................................... 2
Assumptions for the 3300 Programming......................................................................................... 2
Licensing and Option Selection – SIP Licensing ............................................................................ 3
Class of Service Assignment .......................................................................................................... 4
Network Element Assignment ......................................................................................................... 5
Trunk Service Assignment .............................................................................................................. 7
Route Assignment........................................................................................................................... 8
ARS Digits Dialed Assignment........................................................................................................ 9

10-4940-00119 Nortel CS1K
1
Overview
This document provides a reference to Mitel Authorized Solutions providers for configuring
the Mitel 3300 to connect to a Avaya SES. The different devices can be configured in various
configurations depending on your VoIP solution. This document covers a basic setup with
required option setup.
Interop History
Version Date Reason
1 March , 2010 Field Assessed Interop with the 3300 ICP and Avaya SES
Interop Status
The Interop of Avaya SES has been given a Certification status. This service provider or
trunking device will be included in the SIP CoE Reference Guide. The status for the Avaya
SES achieved is:
For informational purposes only, field-assessed means that the Avaya
SES has been tested and/or used to some degree by someone
successfully, though details may or may not be available. Mitel
product support does NOT apply to field-assessed interops.
Software & Hardware Setup
This was the test setup to generate a basic SIP call between the Avaya SES and the 3300 .
Manufacturer Variant Software Version
Mitel 3300 – Mxe Platform 8.0.3.17
Avaya Avaya SES 4.5

10-4940-00119 Nortel CS1K
2
Configuration Notes
This section is a description of how the SIP Interop was configured. These notes should give
a guideline how a device can be configured in a customer environment and how the Avaya
SES and 3300 programming was configured in our test environment.
Disclaimer: Although Mitel has attempted to setup the interop testing facility as closely
as possible to a customer premise environment, implementation setup could be
different onsite. YOU MUST EXERCISE YOUR OWN DUE DILIGENCE IN REVIEWING,
planning, implementing, and testing a customer configuration.
3300 Configuration Notes
The following steps show how to program a 3300 to interconnect with the Avaya SES.
Network Requirements
•There must be adequate bandwidth to support the voice over IP. As a guide, the Ethernet
bandwidth is approx 85 Kb/s per G.711 voice session and 29 Kb/s per G.729 voice
session (assumes 20ms packetization). As an example, for 20 simultaneous SIP
sessions, the Ethernet bandwidth consumption will be approx 1.7 Mb/s for G.711 and
0.6Mb/s. Almost all Enterprise LAN networks can support this level of traffic without any
special engineering. Please refer to the 3300 Engineering guidelines for further
information.
•For high quality voice, the network connectivity must support a voice-quality grade of
service (packet loss <1%, jitter < 30ms, one-way delay < 80ms).
Assumptions for the 3300 Programming
•The SIP signaling connection uses UDP on Port 5060.

10-4940-00119 Nortel CS1K
3
Licensing and Option Selection – SIP Licensing
Ensure that the 3300 is equipped with enough SIP trunking licenses for the connection to the
Avaya SES This can be verified within the License and Option Selection form.
Enter the total number of licenses in the SIP Trunk Licences field. This is the maximum
number of SIP trunk sessions that can be configured in the 3300 to be used with all service
providers, applications and SIP trunking devices.
Figure 1 – License and Option Selection

10-4940-00119 Nortel CS1K
4
Class of Service Assignment
The Class of Service Options Assignment form is used to create or edit a Class of Service
and specify its options. Classes of Service, identified by Class of Service numbers, are
referenced in the Trunk Service Assignment form for SIP trunks.
Many different options may be required for your site deployment, but ensure that “Public
Network Access via DPNSS” Class of Service Option is configured for all devices that make
outgoing calls through the SIP trunks in the 3300.
•Public Network Access via DPNSS set to Yes
•Campon Tone Security/FAX Machine set to Yes
•Busy Override Security set to Yes
Figure 2 – Class of Service

10-4940-00119 Nortel CS1K
5
Network Element Assignment
Create a network element for the Avaya SES. In this example, the Avaya SES is reachable
by FQDN (Make sure the 3300 is using a DNS server that can resolve the FQDN) and is
defined as CS1K-EBX” in the network element assignment form.
Set the transport to UDP and port to 5060.

10-4940-00119 Nortel CS1K
6
SIP Peer Profile
The recommended connectivity via SIP Trunking does not require additional physical
interfaces. IP/Ethernet connectivity is part of the base 3300 Platform. The SIP Peer Profile
should be configured with the following options: NOTE: Ensure the remaining SIP Peer
profile policy options are similar the screen capture below.
Figure 3 – SIP Peer Profile Assignment