Mitsubishi Electric PKFY-P NAMU-E Installation and operation manual

PKFY-1PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
PKFY-P-NBMU-E, NHMU-E, NKMU-E
1. SPECIFICATIONS..................................................................................................................................................PKFY-3
2. EXTERNAL DIMENSIONS.....................................................................................................................................PKFY-6
3. CENTER OF GRAVITY..........................................................................................................................................PKFY-9
4 ELECTRICAL WIRING DIAGRAMS.....................................................................................................................PKFY-10
5. SOUND PRESSURE LEVELS.............................................................................................................................PKFY-13
5-1. Sound Pressure Levels..............................................................................................................................PKFY-13
5-2. NC Curves..................................................................................................................................................PKFY-13
6. TEMPERATURE/AIRFLOW DISTRIBUTIONS....................................................................................................PKFY-14
6-1. Temperature Distributions..........................................................................................................................PKFY-14
6-2. AirowDistributions....................................................................................................................................PKFY-15
7. OPTIONAL PARTS...............................................................................................................................................PKFY-16
7-1. Optional Parts Line Up for the Indoor Unit.................................................................................................PKFY-16
7-2. External Heater Adapter PAC-725AD for PKFY-P06,08NBMU-E ..............................................................PKFY-16
7-3. External Heater Adapter CN24RELAY-KIT-CM3 for PKFY-P12,15NHMU/-P24,30NKMU-E......................PKFY-17
WALL-MOUNTED

PKFY-2 PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
WALL-MOUNTED
IU - H - 2
Wall mounted DATA U3
PKFY-P-NAMU-E, NGMU-E, NFMU-E
I.Wall mounted
PKFY-P-NAMU-E
PKFY-P-NGMU-E
PKFY-P-NFMU-E
Elegant design and compact dimensions ideal for offices, stores and residential uses
ŶThe PKFY auto-vane feature delivers optimal air distribution
and uniform temperature throughout your space.
ŶAll of the performance and design flexibility come in a unit
that is remarkably easy to install and maintain.
ŶThe template and back mounting plate shipped with each
unit makes application a snap.
ŶOperation is among the quietest available
ŶFront grille opens for easy filter cleaning
ŶA wide selection for your design and performance needs
ŶThey are more compact and weigh less than most competitive
units. In addition, they are extremely quiet with one of the
lowest sound ratings available from any manufacturer.
Optimized airflow passage.
Avoid turbo air returning
Avoid dewing at outlet.
PKFY-P-NGMU-E
PKFY-P-NAMU-E
PKFY-P-NFMU-A
Front grille
opens out
PKFY-P-NFMU-E
3.2HP 8.0HP4.0HP 5.0HP
PKFY-P-NAMU-E
PKFY-P-NGMU-E
P08 P12 P15 P18 P30 P36 P48P06 P24 P27 P54 P72
10.0HP
P96
0.8HP 1.0HP 1.3HP 1.6HP 2.0HP 2.5HP 2.8HP 5.6HP
Wall mounted
48,000
6,700
Nominal cooling cap.*1
Nominal heating cap.*2
6,000 8,000 12,000 15,000 18,000 24,000 27,000 30,000 36,000 54,000 72,000 96,000
60,000 80,000 108,00027,000 30,000 34,000 40,000 54,0009,000 13,500 17,000 20,000
BTU/h
BTU/h
* Nominal conditions *1, *2 are referable at the Specification sheet.
PKFY-P-NKMU-E
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
PKFY-P-NBMU-E
PKFY-P-NHMU-E
Elegant design and compact dimensions ideal for offices, stores and residential uses
The PKFY auto-vane feature delivers optimal air distribution
and uniform temperature throughout your space.
All of the performance and design flexibility come in a unit
that is remarkably easy to install and maintain.
The template and back mounting plate shipped with each
unit makes application a snap.
Operation is among the quietest available
Front panel opens for easy filter cleaning
A wide selection for your design and performance needs
They are more compact and weigh less than most competitive
units. In addition, they are extremely quiet with one of the
lowest sound ratings available from any manufacturer.
Optimized airflow passage.
Avoid turbo air returning
Avoid dewing at outlet.
Front panel
opens out
PKFY-P-NKMU-E
PKFY-P-NBMU-E
PKFY-P-NHMU-E
P08P12 P15 P18 P30P36 P48P06 P24 P2
7P
54 P72P96
Wall mounted
48,000
6,700
Nominal cooling cap.*1
Nominal heating cap.*2
6,000 8,000 12,000 15,000 18,000 24,000 27,000 30,000 36,000 54,000 72,000 96,000
60,000 80,000 108,00027,000 30,000 34,000 40,000 54,0009,000 13,500 17,000 20,000
BTU/h
BTU/h
* Nominal conditions *1, *2 are referred to in the Specification sheet.
Built-in wireless receiver for optional PAR-FL32MA remote
controller.
Auto vane and auto fan speed on models P12, P15, and P18
deliver optimal air distribution and uniform temperatures
throughout the space.

PKFY-3PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
1. SPECIFICATIONS
Model PKFY-P06NBMU-E PKFY-P08NBMU-E PKFY-P12NHMU-E PKFY-P15NHMU-E
Powersource 1-phase 208/230V 60Hz
Coolingcapacity(Nominal)*1 BTU / h 6,000 8,000 12,000 15,000
kW 1.8 2.3 3.5 4.4
Powerinput kW 0.03 0.03 0.03 0.03
Current input A 0.15 0.15 0.30 0.30
Heatingcapacity(Nominal)*2 BTU / h 6,700 9,000 13,500 17,000
kW 2.0 2.6 4.0 5.0
Powerinput kW 0.03 0.03 0.03 0.03
Current input A 0.15 0.15 0.30 0.30
MCA A 0.19 0.19 0.38 0.38
Externalnish Plastic,MUNSELL(1.0Y9.2/0.2)
External dimension HxWxD in. 11-5/8 x 32-1/8 x 8-7/8 11-5/8 x 32-1/8 x 8-7/8 11-5/8 x 35-3/8 x 9-13/16 11-5/8 x 35-3/8 x 9-13/16
mm 295x815x225 295x815x225 295x898x249 295x898x249
Netweight lbs (kg) 22 (10) 22 (10) 29(13) 29(13)
Heatexchanger Crossn(Aluminumnandcoppertube)
FAN
TypexQuantity Lineowfanx1 Lineowfanx1 Lineowfanx1 Lineowfanx1
Externalstatic
pressure
in.WG 0.000(208V) 0.000(208V) 0.000(208V) 0.000(208V)
Pa 0 0 0 0
in.WG 0.000(230V) 0.000(230V) 0.000(230V) 0.000(230V)
Pa 0 0 0 0
MotorType 1-phaseinduction
motor 1-phaseinductionmotor DC motor DC motor
Motor output kW 0.008 0.008 0.030 0.030
Drivingmechanism Direct-drivenbymotor
Airowrate
(Low-Mid1-Mid2-
High)
cfm 170-180-200-210 170-180-200-210 320-355-390 320-370-405
m3/ min 4.9-5.2-5.6-5.9 4.9-5.2-5.6-5.9 9-10-11 9-10.5-11.5
L/s 82-87-93-98 82-87-93-98 150-167-183 150-175-192
Sound pressure level
(Low-Mid1-Mid2-High)
(measuredinananechoicroom)
dB <A> 32-33-35-36 32-33-35-36 34-38-42 34-38-42
Insulation material Polyethylenesheet
Airlter PolypropyleneHoneycomb
Protectiondevice Fuse
Refrigerantcontroldevice LEV
Connectableoutdoorunit R410A , R22 CITY MULTI
Diameter of
refrigerant pipe
Liquid (R410A) in.(mm) 1/4(6.35) Flare 1/4(6.35) Flare 1/4(6.35) Flare 1/4(6.35) Flare
(R22) 1/4(6.35) Flare 1/4(6.35) Flare 1/4(6.35) Flare 1/4(6.35) Flare
Gas (R410A) in.(mm) 1/2(12.7) Flare 1/2(12.7) Flare 1/2(12.7) Flare 1/2(12.7) Flare
(R22) 1/2(12.7) Flare 1/2(12.7) Flare 1/2(12.7) Flare 1/2(12.7) Flare
Field drain pipe size in.(mm) I.D. 5/8(16) I.D. 5/8(16) I.D. 5/8(16) I.D. 5/8(16)
Drawing
External - - - -
Wiring - - - -
Refrigerantcycle - - - -
Standard
attachment
Document InstallationManual,InstructionBook
Accessory - - - -
Optional parts External heater adapter PAC-725AD PAC-725AD CN24RELAY-KIT-CM3 CN24RELAY-KIT-CM3
Remarks *Detailsonfoundationwork,ductwork,insulationwork,electricalwiring,powersourceswitch,and
other items shall be referred to the Installation Manual.
VentilationAir:Providingsufcientventilationairisanimportantpartofeverybuildingdesign.
ASHRAEstandard62providestheminimumventilationairrequirements.Alsochecklocalcodes.
Note: *1Nominalcoolingconditions *2Nominalheatingconditions Unitconverter
Indoor: 80degF D.B./ 67degF W.B. 70degF D.B. kcal=kWx860
(26.7degC D.B./ 19.4degC W.B.) (21.1degC D.B.) BTU/h=kWx3,412
Outdoor: 95degF D.B. (35degC D.B.) 47degF D.B./43degF W.B.
(8.3degC D.B./6.1degC W.B.)
cfm=m3/min x 35.31
lb=kg/0.4536
Pipe length: 25ft.(7.6m) 25ft.(7.6m) *Abovespecicationdataissubjecttorounding
variation.
Leveldifference: 0ft.(0m) 0ft.(0m)
*Duetocontinuingimprovement,abovespecicationsmaybesubjecttochangewithoutnotice.

PKFY-4 PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
1. SPECIFICATIONS
Model PKFY-P18NHMU-E PKFY-P24NKMU-E PKFY-P30NKMU-E
Powersource 1-phase 208/230V 60Hz
Coolingcapacity(Nominal)*1 BTU / h 18,000 24,000 30,000
kW 5.3 7.0 8.8
Powerinput kW 0.03 0.04 0.06
Current input A 0.30 0.29 0.43
Heatingcapacity(Nominal)*2 BTU / h 20,000 27,000 34,000
kW 5.9 7.9 10.0
Powerinput kW 0.03 0.04 0.06
Current input A 0.30 0.29 0.43
MCA A 0.38 0.37 0.54
Externalnish Plastic,MUNSELL(1.0Y9.2/0.2)
External dimension HxWxD in. 11-5/8 x 35-3/8 x 9-13/16 14-3/8 x 46-1/16 x 11-5/8 14-3/8 x 46-1/16 x 11-5/8
mm 295x898x249 365x1170x295 365x1170x295
Netweight lbs (kg) 29(13) 46(21) 46(21)
Heatexchanger Crossn(Aluminumnandcoppertube)
FAN
TypexQuantity Lineowfanx1
Externalstaticpressure
in.WG 0.000(208V) 0.000(208V) 0.000(208V)
Pa 0 0 0
in.WG 0.000(230V) 0.000(230V) 0.000(230V)
Pa 0 0 0
MotorType DC motor DC motor DC motor
Motor output kW 0.030 0.056 0.056
Drivingmechanism Direct-drive
Airowrate
(Low-Mid1-Mid2-High)
cfm 320-370-425 570-710 710-850
m3/ min 9-10.5-12 16-20 20-24
L/s 150-175-200 267-333 333-400
Soundpressurelevel(Low-Mid1-Mid2-
High)(measuredinananechoicroom) dB <A> 36-41-45 39-45 43-49
Insulation material Polyethylenesheet
Airlter PolypropyleneHoneycomb
Protectiondevice Fuse
Refrigerantcontroldevice LEV
Connectableoutdoorunit R410A, R22 CITY MULTI
Diameter of
refrigerant pipe
Liquid (R410A) in.(mm) 1/4(6.35) Flare 3/8(9.52) Flare 3/8(9.52) Flare
(R22) 3/8(9.52) Flare 3/8(9.52) Flare 3/8(9.52) Flare
Gas (R410A) in.(mm) 1/2(12.7) Flare 5/8(15.88) Flare 5/8(15.88) Flare
(R22) 5/8(15.88) Flare 5/8(15.88) Flare 5/8(15.88) Flare
Field drain pipe size in.(mm) I.D. 5/8(16) I.D. 5/8(16) I.D. 5/8(16)
Drawing
External - - -
Wiring - - -
Refrigerantcycle - - -
Standard
attachment
Document InstallationManual,InstructionBook
Accessory -L-shapedconnectionpipe L-shapedconnectionpipe
Optional parts External heater adapter CN24RELAY-KIT-CM3 CN24RELAY-KIT-CM3 CN24RELAY-KIT-CM3
Remarks *Detailsonfoundationwork,ductwork,insulationwork,electricalwiring,powersource
switch,andotheritemsshallbereferredtotheInstallationManual.
VentilationAir:Providingsufcientventilationairisanimportantpartofeverybuildingdesign.
ASHRAEstandard62providestheminimumventilationairrequirements.Alsochecklocalcodes.
Note: *1Nominalcoolingconditions *2Nominalheatingconditions Unitconverter
Indoor: 80degF D.B./ 67degF W.B. 70degF D.B. kcal=kWx860
(26.7degC D.B./ 19.4degC W.B.) (21.1degC D.B.) BTU/h=kWx3,412
Outdoor: 95degF D.B. (35degC D.B.) 47degF D.B./ 43degF W.B.
(8.3degC D.B./ 6.1degC W.B.)
cfm=m3/min x 35.31
lb=kg/0.4536
Pipe length: 25ft.(7.6m) 25ft.(7.6m) *Abovespecicationdataissubjecttorounding
variation.
Leveldifference: 0ft.(0m) 0ft.(0m)
*Duetocontinuingimprovement,abovespecicationsmaybesubjecttochangewithoutnotice.

PKFY-5PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
1. SPECIFICATIONS
PKFY-P06NBMU-E
60Hz 208 / 230V 198 to 253V
0.19 / 0.19 0.15 / 0.15
PKFY-P08NBMU-E0.19 / 0.19 0.15 / 0.15
PKFY-P12NHMU-E0.38 / 0.38 0.30 / 0.30
PKFY-P15NHMU-E0.38 / 0.38 0.30 / 0.30
PKFY-P18NHMU-E0.38 / 0.38 0.30 / 0.30
PKFY-P24NKMU-E0.37 / 0.37 0.29 / 0.29
PKFY-P30NKMU-E0.54 / 0.54 0.43 / 0.43
Symbols: MCA : Min.Circuit Amps (=1.25xFLA) FLA : Full Load Amps
IFM :Indoor Fan Motor
Model Indoor Uni
tI
FM
Hz Volts Voltage rang MCA(A) FLA(A)
Electrical characteristics of Indoor unit
e

PKFY-6 PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
2. EXTERNAL DIMENSIONS
PKFY-P06, 08NBMU-E Unit : in(mm)
Detailed figure dwg (ABC)
(Knock out hole)
5/32(4)1-31/32(50)
3/32(2.5) 5/8(16)
1-11/32(34)
13/32(10)
13/32(10) 1-25/32(45)
5°
3°
31/32(24.4)
45°
Knock out hole for
left piping
2-1/8(54)
3-19/32(91.5)1-25/32(45)
3/32(2.5)5/8(16)
1-31/32(50)
13/32(10)
Knock out holt for
under piping
Knock out hole for
remocon wiring
Knock out hole of
remocon wiring
Knock out hole of
right piping
R5/16(R8)
R15/32(R12)
R5/16(R8)
R19/32(R15)
R19/32(R15)
R19/32(R15)
R5/16(R8)
3/16×1-3/8(4.5×35) 4 holes
8- 5/32( 4.3) holes
Installation plate
Piping hole 2-9/16( 65)
87- 3/16( 5.1)holes
4- 11/32( 9)holes
12- 1/8( 2.8)holes
3/16×1-15/32(4.5×37) 4 holes
3/16×1-9/16(4.5×40) 4 holes
Installation plate balance point hole
Knock of hole
60mm or more for
left and left back piping.
Terminal block
Air intake
(Direction)
Address board
Note.1 Use M10 or W3/8 screw for installation plate.
Note.2 Extension piping side.
Note.3 in case of connecting MA-remote controller,please
MA-remote controller cable in anaccssories to the connector.
Transmission
Power supply
Address board
Detailed
Address setting digit
Mode selection
*3 Address board is protected
With PL cover.
Remove thr screw with driver
on the occasion of setting.
Connection No.
Address board
(Direction)
installaion plate
Air intake
Air outlet
(Direction)
Required space
5/8( 16) I.D
1/2F( 12.7)
1/4F( 6.35)
Drain pipe
Liquid pipe
Gas pipe
Refrigerart
piping
Liquid pipe
Gas pipe
Air intake
Air intake
Air intake
13/32(10)
13/32(10)
16-1/32(407.5)
11-23/32(298) 10-1/4(260) 8-27/32(225)
7-15/32(190)
6-3/32(155) 4-23/32(120) 3-11/32(85) 1-3/16(30)
16-1/32(407.5)
12-29/32(328) 11-5/8(295) 10-1/4(260) 8-27/32(225) 7-15/32(190)
6-3/32(155)
4-23/32(120) 3-11/32(85) 1-3/16(30)
5-1/4(133)
2-27/32(72.5)
3-11/32(85)
1-7/8(47.5)
2-3/8(60)
7/8(22.5)
0
4-13/16(122.5)
4-1/32(102.5)
19/32(15)
12-29/32(328)
6-5/8(168)
4-7/16(113)
3-7/16(87)
5-5/16(135)
4-11/32(110)
1-3/8(35)
13/32(10)
4-7/8(124)
3-17/32(90)
6-1/4(159)
2-9/16(65)
1-9/16(40)
5-1/32(128)
11-23/32(298)
9-1/4(235)
8-1/16(205)
6-7/8(175)
6-11/16(170)
0
1-3/4(45)
4-29/32(125)
2-3/32(53)
1-3/32(27.5)
0
7-3/32(180)
6-1/4(159)
0
3-27/32(97.5)
8-1/16(205)
6-11/16(170)
9-1/4(235)
6-7/8(175)
1-23/32(44)
1-31/32(50)
Details of installation plate
Min55/64(22) Min25/32(20)
Min3-15/16(100)
Min3-35/64(90)
Min1-31/32(50)
1-7/16(37.8)
1/4
(7)
Air intake
25-3/16(640)
Air intake
32-3/32(815)
4-1/2(115)
4-3/16(106.7)
1/8(3)
11-39/64(295)
2-3/8
(60)
25-3/16(640)
27-3/8(695)
8-55/64(225) 3/16(5)
4-11/32(110)
4-9/16(116)
26-31/32(660)(Drain pipe total 29-29/32(760))
17-23/32(450)
20-25/32(520)
3-15/16(100.6)17/32(14)
30-13/16(783)
2-7/8
(74.6)
Air outlet
Air outlet
Wireless Receiver
Operation lamp
DEFROST/STAND BY lamp

PKFY-7PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
2. EXTERNAL DIMENSIONS
PKFY-P12, 15, 18NHMU-E Unit : in(mm)
1/2F ( 12.7)
1/4F ( 6.35)
Refrigerart
Piping
Drain hose
Gas pipe
Liquid pipe
2-1/2~3-1/8
( 65~ 80)
2-1/2~ 3-1/8
( 65~ 80)
Through hole
Sleeve
(purchased locally)
Center measurement hole 3/32( 2.5)
5/32(3.8)
2-1/4(58) 0
Wall hole
for
left rear
piping Knock out hole for
left rear piping
2-3/4×12-3/16(70×310) Wall hole for
right rear piping
77- 3/16( 5.1)
Tapping
screw hole
4- 5/16( 9) Bolt hole Mount board
Indoor unit outline
0
5/8(16)
9-15/16(253.5)
9-1/8(232.5)
1-1/16(28.5)
1-9/16(41)
3-1/16(78.5)
4-1/16(103.5)
4-9/16(116)
6-1/2(166)
7(178.5)
8(203.5)
3-9/16(91)
13/16(21.8)
9-1/16(231.5)
10-3/4(273.2)
0
1-1/4(32.7)
2-9/16(66)
2-1/16(53.5)
5(128.5)
6(153.5)
3/4(20)
9/16(15)
14-5/8(372.3) 14(356.3) 12-7/8(237.5) 11-7/16(291.5) 10-3/8(265) 9-5/16(238) 8-13/16(225) 7-13/16(200)
4-7/8(125)
2-3/4(70)
9/16(15)
14-5/8(372.3) 14(356.3) 12-7/8(327.5) 10-3/8(265) 11-7/16(291.5) 7-13/16(200) 8-13/16(225) 4-7/8(125) 2-3/4(70) 0
17-5/8(449)
7-9/16(193.5)
7-1/16(180.3)
6-9/16(167)
5-1/2(140)
4-1/2(115)
6-13/16(174)
8-3/8(213)
9-5/16(238)
10-15/16(278.3)
15-1/2(394)
11-1/16(281)
17-5/8(449)
0
Emergency operation switch
(cooling/heating)
Terminal block for
MA-remote controller
Terminal block for transmission
Front side(Grille open)
Terminal block for power supply
17-15/16(457)Gas pipe
21-3/16(539)Liquid pipe 6-5/8(169)
6-3/16(158)
24(610)Drain hose 7-3/16(184)
250mm,9-13/16inch or greater with optional drain pump installation.
Required space(Indoor unit) (mm)
Air inlet
Air inlet
Air outlet
Min.1-31/32(50)
Min.9-13/16(250)
Min.5-7/8(150)
Min.8-5/8
(220)
Min.1-31/32(50)
Min.1/4(7)
Knock out hole for piping
D
2-3/16(56)
2-11/16(69)
3/16(6)
1-11/16(43)
C
2-3/16(56)7/16(12.5)
1-11/16(43)
B
1-3/4(46)
2-5/16(60)
2-5/16(59)
1-11/16(43)
A
1-11/16(43)
1-3/4(46)
2-3/16(56)
3/16(6)
A
Knock out hole
for right piping
Right side
Mount board
3/16(5)9-3/4(249)
Top side
15-3/16(387) 7-1/2(192)
7-3/4(197)
23-9/16(599)
CB
Operation lamp DEFROST/STAND BY lamp
Wireless Receiver
Louver(manual)
Vane(auto)
Knock out hole
for lower piping
Knock out hole
for lower piping
Under side
5/16(8)
24-1/16(612)
DKnock out hole
for left piping
Left side
Front side
6-1/16(155)
2-1/8
(55) 27-1/16(688)
11-9/16(295)
35-5/16(898)
5/8 ( 16) I.D

PKFY-8 PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
2. EXTERNAL DIMENSIONS
PKFY-P24, 30NKMU-E Unit : in(mm)
Front side
46-1/16(1170) 9-1/2(241)
33-21/32(855)2-29/32(74)
14-3/8(365)
Emergency operation switch
(cooling/heating)
Terminal block for power supply
Terminal block for
MA-remote controller
Front side(Grille open)
Terminal block for transmission
Filter hook
6-1/16(154)
4-27/32(123)
18-31/32(482)Liquid pipe
17-15/32(444)Gas pipe
23-1/32(585)Drain hose 5-9/32(134)
Min.9/32(7)
Center measurement hole
3/32( 2.5)
Knock out hole for
left rear piping
2-15/16×18-29/32(75×480)
75- 3/16( 5.1)
Tapping
screw hole
Mount board
Wall hole for
right rear piping
Indoor unit outline
4- 11/32( 9) Bolt hole
Wall hole for
left rear piping
1/8(3)
R1-15/32(R37.5)
2-1/8(54) 0
5/8(15.5) 0
17-9/32(439) 0
17-9/32(439)
15-1/8(384)
13/32(10) 20-3/8(517.4) 17-7/8(454) 16-3/32(408.5) 15-1/8(384) 14-11/32(364) 12-3/8(314) 4-11/32(110)
2-3/8(60) 13/32(10) 18-5/16(465.5) 17-7/8(454)
16-3/32(408.5)
15-1/8(384.5) 14-11/32(364) 12-3/8(314) 4-11/32(110)
2-3/8(60)
1-1/4(32)
12-5/32(308.5)
31/32(25)
11-1/2(292)
11(279.5)
9-17/32(242)
7-9/16(192)
5-19/32(142)
4-29/32(125)
4-19/32(117)
3-15/16(100)
2-15/16(75)
1-31/32(50)
15-1/8(384)
0
13-3/4(349.2)
16-15/16(430.5)
1/2(12.5)
11-1/2(292)
10-13/32(264)
9-1/32(229.5)
8-17/32(217)
6-9/16(167)
5-3/32(129.5)
4-1/8(104.5)
3-7/16(87.5)
2-15/32(62.5)
1-15/32(37.5)
1/2(12.5)
2-1/8(54)
31/32(25)
0
12-1/4(311)
8-17/32(216.5)
13-11/32(339)
20-7/8(530.5)
7-7/16(189)
13-11/32(339)
17-11/16(449.2)
23-1/32(585)
23-1/32(585)
A
5/16(7.8) 3-1/32(77)
2-5/8(67)
2-9/16(65)
B
Knock out hole for piping
13/32(10.7)
2-9/16(65)
3-1/32(77)
3-7/16(87)
C
5/16(7.8)
2-9/16(65)
3-1/32(77)
2-5/8(67)
Louver(manual)
Vane(auto)
Knock out hole
for lower piping
Under side
BB
Receiver
DEFROST/STAND BY lamp
Operation lamp
2-19/32(66)
23/32(18)
1-1/4(32)
2-3/32(53)
1-3/16(30)
1-3/8(35)
Mount board
C
Knock out hole
for right piping
Right side
11-5/8(295) 3/16(5)
Left side
A
Knock out hole
for left piping
Top side
2-9/16(65.2)
5-17/132(140.3)
7/16(11)
17(431.7)16-11/16(423.7)
Air outlet
Air inlet
Min.1-7/8(48)
Min.9-27/32(250)
(inch)
Required space(Indoor unit)
Min.2(50.5)Min.8-21/32(220)
Min.2-27/32(72.4)
3
2
1
Refrigerant pipe: 3/8 O.D( 9.52)
Refrigerant pipe: 5/8 O.D( 15.88)
5/8( 16) I.D
3 Drain hose
Piping connection department
1 Liquid pipe
2 Gas pipe
Through hole
2-15/16
( 75) 2-15/16~ 3-5/32
( 75~ 80)
Sleeve
(purchased locally) Flared connection: 5/8F
Flared connection: 3/8F

PKFY-9PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
PKFY-P-NBMU-E, NHMU-E, NKMU-E
X
D
Y
W
Z
H
in(mm)
Model WDHXYZ
PKFY-P06NBMU-E (815)
32-1/8 (225) 8-7/8 (295) 11-5/8 (120) 4-3/4 (300) 11-13/16 (150) 5-15/16
PKFY-P08NBMU-E (815)
32-1/8 (225) 8-7/8 (295) 11-5/8 (120) 4-3/4 (300) 11-13/16 (150) 5-15/16
PKFY-P12NHMU-E (898)
35-3/8 (249) 9-13/16 (295) 11-5/8 (120) 4-3/4 (390) 15-3/8 (160) 6-5/16
PKFY-P15NHMU-E (898)
35-3/8 (249) 9-13/16 (295) 11-5/8 (120) 4-3/4 (390) 15-3/8 (160) 6-5/16
PKFY-P18NHMU-E (898)
35-3/8 (249) 9-13/16 (295) 11-5/8 (120) 4-3/4 (390) 15-3/8 (160) 6-5/16
PKFY-P24NKMU-E (1170)
46-1/8 (295) 11-5/8 (365) 14-3/8 (190) 7-1/2 (460) 18-1/8 (190) 7-1/2
PKFY-P30NKMU-E (1170)
46-1/8 (295) 11-5/8 (365) 14-3/8 (190) 7-1/2 (460) 18-1/8 (190) 7-1/2
3. CENTER OF GRAVITY

PKFY-10 PKFY-P-NBMU-E/PKFY-P-NHMU-E/PKFY-P-NKMU-E (June 2010)
PKFY-P-NBMU-E
PKFY-P-NHMU-E
PKFY-P-NKMU-E
4. ELECTRICAL WIRING DIAGRAMS
PKFY-P06,08NBMU-E
Mark Meaning
LED1 Main power supply Main power supply (indoor unit: 208-230V)
power on lamp is lit
Function
LED on indoor board for service
ON
OFF 1234
MODELS SW2
P06 ON
OFF 1234
MODELS SW2
P08
<*1>
LED2 Power supply for
MA-Remote controller Power supply for MA-Remote controller on lamp is lit
Legend
Symbol
I.B
CN32
CN51
CN52-2
SW2
SW2
SW3 TH21
TH22
Remote switch
Centrally control
External Heater
Capacity code
Mode selection Room temp.detection
(32°F/15k ,77°F/5.4k )
Pipe temp.detection/Liquid
(32°F/15k ,77°F/5.4k )
Name
Indoor controller board
P.B
W.B
Indoor power board
ZNR Varistor
FUSE
Fuse (6A 250V)
F.CFan phase control
MF Fan motor
C1 Capacitor (Fan motor)
MV Vane motor
LEV Linear expansion valve
Connector
Switch
Switch
Thermistor
Symbol
TB2
TB5 Power supply
Transmission
Address board
Mode selection
Name Symbol Name
Terminal
block
TH23
Pipe temp.detection/Gas
(32°F/15k ,77°F/5.4k )
Note
1.At servicing for outdoor unit, always follow the wiring diagram of outdoor unit.
2.In case of using MA-remote controller,please connect MA-remote controller cable in an accessory
to the connector . (Remote controller wire is non-polar.)
3.In case of using M-NET,please connect to TB5 (Transmission line is non-polar.)
4.Symbols used in wiring diagram above are, : terminal block, : connector
5.The setting of the SW2 dip switches differs in the capacity. For the detail, refer to the fig :*1.
6.Please set the switch SW5 according to the power supply voltage.
Set SW5 to 230V side when the power supply is 230 volts.
When the power supply is 208 volts, set SW5 to 208V side.
12
A.B SW1
SW1
SW5
RU
BZ
LED1 LED(Operation indicator:Green)
LED
(Preparation for heating:Orange)
Emergency operation (Heat)
Emergency operation (Cool)
LED2
SW11
SW12
SW14
Voltage selection
Address setting 1s digit
Address setting 10ths digit
Branch No.
Switch
Receving unit
Buzzer
Wireless remote controller board
MV
MRED
WHT
BLU
ORN
YLW
CN5V
VANE
(BLU)
CN52-2CN51
CN41
CN32
6
5
9
CN60
LEV
(WHT)
BRN RED
BLU
ORN
YLW WHT
9
CN3A
MA-
REMOCON
(BLU)
MF
FAN
(GRN) CND
(RED)
CN2M
M-NET
(BLU)
TO OUTDOOR UNIT
BC CONTROLLER
M-NET REMOTE CONTROLLER
DC24-30V
BREAKER
(16A)
FUSE
(16A)
PULL
BOX
TB2
TO NEXT
INDOOR UNIT
POWER SUPPLY
208/230V 60Hz
RED RED WHT BLK BLU
GRN /YLW
BLU BLU
1TB5 2
TO MA-REMOTE
CONTROLLER
DC8.7-13V
ORN ORN
ZNR FUSE
250V
6A
C1
LED1
CN35P
(BLU)
F.C
CN53P
(RED)
CN53M
(RED)
CN35M
(BLU)
LED2
CN29
GAS
(BLK)
CN21
LIQUID
(WHT)
TH23 TH22
CN20
INTAKE
(RED)
TH21
CN81
ADDRESS
(RED)
(RED)
ADDRESS
CN82
CN42
ADDRESS
(RED)
(RED)
ADDRESS
CN43
SW2SW3
123456789 10
1234
ON
OFF
I.B
See fig :*1
SW5
SW1
208V 230V
A.B
W.B
ON
OFF
0
SW12
10ths
DIGIT
0
SW11 0
SW14
1s
DIGIT BRANCH
No.
P.B
4
8
12345678910
4
1
11 112
12 13
2
13
13
146
13 14
56 CN90
WIRELESS
(WHT)
91
1418
1
1
5
5
8
1
1
5
LED2
CNB
RU
SW2SW1
LED1 BZ t° t° t°
M
M
1~
LEV
M1M2
U
L1
L2
13 12
1515
<*2>
GR
<*2>Use copper supply wires.
Drain Safety
CN20