Mitsubishi Electric MR-J5D-G User manual

MR-J5D-G
User's Manual
(Introduction)
-MR-J5D_-_G_
Mitsubishi Electric AC Servo System

1
SAFETY INSTRUCTIONS
Please read the instructions carefully before using the equipment.
To use the equipment correctly, do not attempt to install, operate, maintain, or inspect the equipment until you have read
through this manual, installation guide, and appended documents carefully. Do not use the equipment until you have a full
knowledge of the equipment, safety information and instructions.
In this manual, the safety instruction levels are classified into "WARNING" and "CAUTION".
Note that the CAUTION level may lead to a serious consequence depending on conditions.
Please follow the instructions of both levels because they are important to personnel safety.
Forbidden actions and required actions are indicated by the following diagrammatic symbols.
In this manual, precautions for hazards that can lead to property damage, instructions for other functions, and other
information are shown separately in the "POINT" area.
After reading this manual, keep it accessible to the operator.
WARNING
Indicates that incorrect handling may cause hazardous conditions, resulting in
death or severe injury.
CAUTION
Indicates that incorrect handling may cause hazardous conditions, resulting in
medium or slight injury.
Indicates a forbidden action. For example, "No Fire" is indicated by .
Indicates a required action. For example, grounding is indicated by .

2
[Transportation]
[Installation/wiring]
[Setting/adjustment]
[Operation]
[Maintenance]
CAUTION
●To prevent injury, transport the products correctly according to their mass.
WARNING
●To prevent an electric shock, turn off the power and wait for 20 minutes or more before starting wiring
and/or inspection.
●To prevent an electric shock, ground the converter unit/drive unit.
●To prevent an electric shock, any person who is involved in wiring should be fully competent to do the
work.
●To prevent an electric shock, do not attempt to wire the converter unit/drive unit until it have been
mounted.
●To prevent an electric shock, connect the protective earth (PE) terminal of the converter unit/drive unit
to the protective earth (PE) of the cabinet, then connect the grounding lead wire to the ground.
●To prevent an electric shock, do not touch the conductive parts.
WARNING
●To prevent an electric shock, do not operate the switches with wet hands.
WARNING
●To prevent an electric shock, do not operate the switches with wet hands.
WARNING
●To prevent an electric shock, any person who is involved in inspection should be fully competent to do
the work.
●To prevent an electric shock, do not operate the switches with wet hands.

3
DISPOSAL OF WASTE
Please dispose of this product, battery (primary battery), and other options according to your local laws and regulations.
ABOUT THE MANUAL
e-Manuals are Mitsubishi Electric FA electronic book manuals that can be browsed with a dedicated tool.
e-Manuals enable the following:
• Searching for desired information in multiple manuals at the same time (manual cross searching)
• Jumping from a link in a manual to another manual for reference
• Browsing for hardware specifications by scrolling over the components shown in product illustrations
• Bookmarking frequently referenced information
• Copying sample programs to engineering tools

4
If using the servo for the first time, prepare and use the following related manuals to ensure that the servo is used safely.
No. Manual name Manual No.
(1) MR-J5D-G User's Manual (Introduction) IB(NA)-0300538ENG
(2) MR-J5D User's Manual (Hardware) IB(NA)-0300548ENG
(3) MR-CV Power Regeneration Converter Unit User's Manual IB(NA)-0300553ENG
(4) Rotary Servo Motor User's Manual (HK series) SH(NA)-030314ENG
(5) MR-J5 Partner's Encoder User's Manual SH(NA)-030320ENG
(6) MR-J5 User's Manual (Function) SH(NA)-030300ENG
(7) MR-J5-G/MR-J5W-G User's Manual (Communication Function) SH(NA)-030302ENG
(8) MR-J5 User's Manual (Adjustment) SH(NA)-030306ENG
(9) MR-J5 User's Manual (Troubleshooting) SH(NA)-030312ENG
(10) MR-J5-G/MR-J5W-G User's Manual (Parameters) SH(NA)-030308ENG
(11) MR-J5-G/MR-J5W-G User's Manual (Object Dictionary) SH(NA)-030304ENG
(4) Rotary Servo Motor
This manual is necessary primarily for installing, wiring, and
using options.
The manual is necessary for adjustment of operation status.
The manual is necessary for using communication functions.
The manual is necessary for specifying the causes of alarms
and warnings.
(5) Partner Encoder
(6) Function
(8) Adjustment
(11) Object Dictionary
(9) Troubleshooting
(1) Introduction
(2) Hardware
(7) Communication Function
(10) Parameters It describes the parameters of the drive unit.
It describes the objects for the drive unit.
The manual is necessary for operating drive units.
For the usage of each function, refer to this manual.
(3) Converter unit

5
Interpreting servo parameter numbers
For a servo parameter which uses one particular digit to select a function, the position of its digit indicates the detail number of
the servo parameter, and the value in hexadecimal which is set to the digit indicates the selected function.
For example, the detail number of the servo parameter in the last digit is expressed as [Pr. PA01.0]. In addition, a servo
parameter which uses a combination of several digits to select a function, is expressed using "-" as seen in [Pr. PA01.0-1].
The following is an example of the servo parameter number PA01 with the setting values of "FEDCBA98" in hexadecimal.
• When setting a servo parameter with one particular digit
• When setting a servo parameter using a combination of several digits
For example, if the servo parameter name is "Function selection A-1", the setting digit name is "Forced stop deceleration
function selection", and the setting digit is the forth last digit in PA04, the servo parameter is expressed as shown below.
[Pr. PA04.3 Forced stop deceleration function selection]
U.S. CUSTOMARY UNITS
U.S. customary units are not shown in this manual. Convert the values if necessary according to the following table.
Servo
parameter
Symbol Name Description
PA04.3 *AOP Forced stop deceleration function
selection
Set "Forced stop deceleration function" to enabled/disabled.
Initial value: 1h (enabled)
Quantity SI (metric) unit U.S. customary unit
Mass 1 [kg] 2.2046 [lb]
Length 1 [mm] 0.03937 [inch]
Torque 1 [N•m] 141.6 [oz•inch]
Moment of inertia 1 [(× 10-4 kg•m2)] 5.4675 [oz•inch2]
Load (thrust load/axial load) 1 [N] 0.2248 [lbf]
Temperature N [°C] × 9/5 + 32 N [°F]
[Pr. PA01] =
PA01.0 = "8"
PA01.1 = "9"
PA01.2 = "A"
PA01.3 = "B"
PA01.4 = "C"
PA01.5 = "D"
CDBFAE89
PA01.6 = "E"
PA01.7 = "F"
Detail No.
[Pr. PA01] =
PA01.0-1 = "98"
PA01.2-4 = "CBA"
PA01.5 = "D"
CDBFAE89
PA01.6 = "E"
PA01.7 = "F"
Detail No.

6
CONTENTS
SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
DISPOSAL OF WASTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ABOUT THE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
U.S. CUSTOMARY UNITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
CHAPTER 1 SPECIFICATIONS 8
1.1 Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2 Model designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3 Combination with drive units and servo motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.4 Drive unit standard specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MR-J5D1-_G_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MR-J5D2-_G_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MR-J5D3-_G_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Positioning mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Functional safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.5 Function block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MR-J5D1-_G_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MR-J5D2-_G_/MR-J5D3-_G_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1.6 Configuration including peripheral equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.7 Special specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Drive units without the dynamic brake (-ED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
CHAPTER 2 FUNCTION 21
2.1 Restrictions on the MR-J5_-_G_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Restrictions on CC-Link IE TSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Restrictions on CC-Link IE Field Network Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.2 Function list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.3 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
CHAPTER 3 STRUCTURE 33
3.1 Parts identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.2 Switch setting and display of the drive unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7-segment LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Status LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
CHAPTER 4 STARTUP 43
4.1 Turning on drive unit for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Test operation of the servo motor alone in test operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Equipment configuration setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Controller-related setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Operation by controller command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.2 Instructions on startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.3 Troubleshooting at startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.4 Duplicate setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Duplication using MR Configurator2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.5 Test operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

7
CONTENTS
Execution method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Test operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Motor driving by test operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Motor-less operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Output signal (DO) forced output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.6 Drive unit setting initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Initialization procedure by MR Mode Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
CHAPTER 5 MAINTENANCE, INSPECTION AND PARTS REPLACEMENT 61
5.1 Inspection items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Periodic inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5.2 Parts with a service life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5.3 Replacing fan unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
CHAPTER 6 COMPLIANCE WITH GLOBAL STANDARDS 63
6.1 Compliance with global standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.2 Handling of AC servo amplifier batteries for the United Nations Recommendations
on the Transport of Dangerous Goods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.3 Symbol for the new EU Battery Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.4 Compliance with China Compulsory Certification (CCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.5 Compliance with the China RoHS directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
REVISIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

81 SPECIFICATIONS
1.1 Outline
1SPECIFICATIONS
1.1 Outline
The MR-J5D_-_G_ is a drive unit that operates in the Ethernet open network (communication speed of up to 1 Gbps).
Each of the MR-J5D2-_G_ and the MR-J5D3-_G_ drive units can drive two or three servo motors. The footprint of the MR-
J5D2-_G_ drive unit and the MR-J5D3-_G_ drive unit is considerably smaller than that of two or three MR-J5D1-_G_ drive
units.
1.2 Model designation
Rating plate
The following shows an example of the rating plate for explanation of each item.
CC-Link IE TSN authentication class
Serial number
Model
Capacity
Applicable power supply
Rated output
Standard, manual number
Ambient temperature
IP rating
KC certification number
The year and month of manufacture
Country of origin

1 SPECIFICATIONS
1.3 Combination with drive units and servo motors 9
1
Model
The following describes what each block of a model name indicates. Not all combinations of the symbols are available.
■MR-J5D_-_G_
*1 For 2-axis or 3-axis drive units
*2 For 3-axis drive units
*1 : The corresponding item is included or supported. : The corresponding item is not included or not supported.
1.3 Combination with drive units and servo motors
Refer to "Combination with drive units and servo motors" in the following manual.
MR-J5D User's Manual (Hardware)
Item Special specifications *1 Detailed explanation
Not attached (standard model) -ED
MR-
J5D1
MR-
J5D2
MR-
J5D3
MR-
J5D1
MR-
J5D2
MR-
J5D3
CN2AL connector Page 35 External
encoder connector
Fully closed loop system
Scale measurement function
Two-wire type 
Four-wire type 
A/B/Z-phase
differential input

Built-in dynamic brake Page 20 Drive units
without the dynamic brake
(-ED)
100 1
200 2
350 3.5
500 5
700 7
1
2
3.5
5
7
-
-
2
1
-
MR - - -100G EDJ5D1 4
D2 2
D1 1
D3 3
-ED
4
Series
Number of axes
CC-Link IE TSN interface
Number
of axes
Rated output
Symbol
Rated output [kW]
Symbol A-axis B-axis *1 C-axis *2
Special specification
Symbol Special specification
Standard
None
Without the dynamic brake
Symbol
Power supply
Power supply
3-phase 380 V AC to 480 V AC

10 1 SPECIFICATIONS
1.4 Drive unit standard specifications
1.4 Drive unit standard specifications
MR-J5D1-_G_
400 V class
*1 This value is applicable when all I/O signals are used. Reducing the number of I/O points decreases the current capacity.
*2 The command communication cycle depends on the controller specifications and the number of the connected axes.
*3 The side protective cover (option) is required for IP20.
Model: MR-J5D1- 100G4 200G4 350G4 500G4 700G4
Output Voltage 3-phase 0 V AC to 480 V AC
Rated current [A] 3.0 5.5 8.6 14.0 17.0
Main circuit power supply input The main circuit power supply of the drive unit is supplied from a converter unit.
Control circuit power
supply input
Voltage/Frequency 1-phase 380 V AC to 480 V AC, 50 Hz/60 Hz
Rated current [A] 0.2
Permissible voltage
fluctuation
1-phase 323 V AC to 528 V AC
Permissible
frequency
fluctuation
Within ±5 %
Power consumption
[W]
40
Inrush current [A] Refer to "Inrush currents at power-on of control circuit" in the following manual.
MR-J5D User's Manual (Hardware)
Interface power supply Voltage 24 V DC ±10 %
Current capacity [A] 0.3 (including CN8 connector signals) *1
Control method Sine-wave PWM control, current control method
Dynamic brake Built-in
CC-Link IE TSN Communication
cycle *2
31.25 μs, 62.5 μs, 125 μs, 250 μs, 500 μs, 1 ms, 2 ms, 4 ms, 8 ms
Authentication
class
Class B
CC-Link IE Field Network Basic Supported
Communication
function
USB Connection to a personal computer or other devices (MR Configurator2-compatible)
Encoder output pulses Compatible (A/B/Z-phase pulse)
Analog monitor Two channels
Fully closed loop control Supported
Scale measurement function Supported
Load-side encoder interface Mitsubishi Electric high-speed serial communication/A/B/Z-phase differential input signal
Protective functions Overcurrent shut-off, overload shut-off (electronic thermal), servo motor overheat protection, encoder error
protection, undervoltage protection, instantaneous power failure protection, overspeed protection, excessive
error protection, magnetic pole detection protection, and linear servo control error protection
Satisfied standards CE marking LVD: EN 61800-5-1, EMC: EN 61800-3, MD: EN ISO 13849-1:2015, EN 61800-5-2, EN 62061
UKCA marking LVD: BS EN 61800-5-1, EMC: BS EN IEC 61800-3, MD: BS EN ISO 13849-1:2015, BS EN 61800-5-2, BS EN
62061
UL standard UL 61800-5-1
Structure (IP rating) Natural cooling, open (IP20) *3 Force cooling, open (IP20) *3
Mass [kg] 5.5 4.6

1 SPECIFICATIONS
1.4 Drive unit standard specifications 11
1
MR-J5D2-_G_
400 V class
*1 This value is applicable when all I/O signals are used. Reducing the number of I/O points decreases the current capacity.
*2 The command communication cycle depends on the controller specifications and the number of the connected axes.
*3 The side protective cover (option) is required for IP20.
*4 If the safety sub-function by a network (when [Pr. PSA01.0] is set to "1" and [Pr. PSA01.1] is set to "1") is used, encoder output pulses
will not be output.
Model: MR-J5D2- 100G4 200G4 350G4 500G4 700G4
Output Voltage 3-phase 0 V AC to 480 V AC
Rated current (each
axis) [A]
3.0 5.5 8.6 14.0 17.0
Main circuit power supply input The main circuit power supply of the drive unit is supplied from a converter unit.
Control circuit power
supply input
Voltage/Frequency 1-phase 380 V AC to 480 V AC, 50 Hz/60 Hz
Rated current [A] 0.2
Permissible voltage
fluctuation
1-phase 323 V AC to 528 V AC
Permissible
frequency
fluctuation
Within ±5 %
Power consumption
[W]
40
Inrush current [A] Refer to "Inrush currents at power-on of control circuit" in the following manual.
MR-J5D User's Manual (Hardware)
Interface power supply Voltage 24 V DC ±10 %
Current capacity [A] 0.35 (including CN8 connector signals) *1
Control method Sine-wave PWM control, current control method
Dynamic brake Built-in
CC-Link IE TSN Communication
cycle *2
62.5 μs, 125 μs, 250 μs, 500 μs, 1 ms, 2 ms, 4 ms, 8 ms
Authentication
class
Class B
CC-Link IE Field Network Basic Not supported
Communication
function
USB Connection to a personal computer or other devices (MR Configurator2-compatible)
Encoder output pulses Compatible (A/B-phase pulse) *4
Analog monitor Two channels
Fully closed loop control Supported
Scale measurement function Supported
Load-side encoder interface Mitsubishi Electric high-speed serial communication
Protective functions Overcurrent shut-off, overload shut-off (electronic thermal), servo motor overheat protection, encoder error
protection, undervoltage protection, instantaneous power failure protection, overspeed protection, excessive
error protection, magnetic pole detection protection, and linear servo control error protection
Satisfied standards CE marking LVD: EN 61800-5-1, EMC: EN 61800-3, MD: EN ISO 13849-1:2015, EN 61800-5-2, EN 62061
UKCA marking LVD: BS EN 61800-5-1, EMC: BS EN IEC 61800-3, MD: BS EN ISO 13849-1:2015, BS EN 61800-5-2, BS EN
62061
UL standard UL 61800-5-1
Structure (IP rating) Natural cooling,
open (IP20) *3
Force cooling, open (IP20) *3
Mass [kg] 5.7 5.6 6.2

12 1 SPECIFICATIONS
1.4 Drive unit standard specifications
MR-J5D3-_G_
400 V class
*1 This value is applicable when all I/O signals are used. Reducing the number of I/O points decreases the current capacity.
*2 The command communication cycle depends on the controller specifications and the number of the connected axes.
*3 The side protective cover (option) is required for IP20.
*4 If [Pr. PT01.1 Speed/acceleration/deceleration unit selection] is set to "1" (command unit/s), if the safety sub-function by a network
(when [Pr. PSA01.0] is set to "1" and [Pr. PSA01.1] is set to "1") is used, or if TPR1 (touch probe 1) to TPR3 (touch probe 3) are
assigned to devices, encoder output pulses will not be output.
Model: MR-J5D3- 100G4 200G4
Output Voltage 3-phase 0 V AC to 480 V AC
Rated current (each
axis) [A]
3.0 5.5
Main circuit power supply input The main circuit power supply of the drive unit is supplied from a converter unit.
Control circuit power
supply input
Voltage/Frequency 1-phase 380 V AC to 480 V AC, 50 Hz/60 Hz
Rated current [A] 0.2
Permissible voltage
fluctuation
1-phase 323 V AC to 528 V AC
Permissible
frequency
fluctuation
Within ±5 %
Power consumption
[W]
40
Inrush current [A] Refer to "Inrush currents at power-on of control circuit" in the following manual.
MR-J5D User's Manual (Hardware)
Interface power supply Voltage 24 V DC ±10 %
Current capacity [A] 0.45 (including CN8 connector signals) *1
Control method Sine-wave PWM control, current control method
Dynamic brake Built-in
CC-Link IE TSN Communication
cycle *2
250 μs, 250 μs, 500 μs, 1 ms, 2 ms, 4 ms, 8 ms
Authentication
class
Class B
CC-Link IE Field Network Basic Not supported
Communication
function
USB Connection to a personal computer or other devices (MR Configurator2-compatible)
Encoder output pulses Available only on axes A and B (A/B-phase pulse) *4
Analog monitor Two channels
Fully closed loop control Not supported
Scale measurement function Not supported
Protective functions Overcurrent shut-off, overload shut-off (electronic thermal), servo motor overheat protection, encoder error
protection, undervoltage protection, instantaneous power failure protection, overspeed protection, excessive
error protection, magnetic pole detection protection, and linear servo control error protection
Satisfied standards CE marking LVD: EN 61800-5-1, EMC: EN 61800-3, MD: EN ISO 13849-1:2015, EN 61800-5-2, EN 62061
UKCA marking LVD: BS EN 61800-5-1, EMC: BS EN IEC 61800-3, MD: BS EN ISO 13849-1:2015, BS EN 61800-5-2, BS EN
62061
UL standard UL 61800-5-1
Structure (IP rating) Natural cooling, open (IP20) *3 Force cooling, open (IP20) *3
Mass [kg] 5.9 5.8

1 SPECIFICATIONS
1.4 Drive unit standard specifications 13
1
Positioning mode
Point table method (CP)
Item Description
Command interface Object dictionary
Operational specifications Positioning by specifying the point table number (255 points)
System Signed absolute value command method
Position command input Absolute value command method Setting in the point table
Setting range of feed length for one point:
-2147483648 to 2147483647 [μm],
-214748.3648 to 214748.3647 [inch],
-2147483648 to 2147483647 [pulse],
-360.000 to 360.000 [degree]
Speed command input Set the servo motor speed in the point table.
Set the acceleration/deceleration time constants and acceleration/deceleration
in the point table.
Set the S-pattern acceleration/deceleration time constant in [Pr. PT51].
The speed unit can be selected ([r/min], command unit/s).
The acceleration/deceleration unit can be selected ([ms], command unit/s2).
Torque limit Setting by the servo parameter or object dictionary
Point table mode (pt) Each positioning operation Point table number input method
Perform each positioning operation based on the position command and speed
command.
Continuous positioning operation Varying-speed operation (2 to 255 speeds)/
Continuous positioning operation (2 points to 255 points)/
Continuous operation to the point table selected at startup/
Continuous operation to the point table No. 1
Jog mode (jg) JOG operation Perform inching operation in the network communication function based on the
speed command.
Homing mode (hm) For information on the homing method, refer to "Homing mode (hm) and
homing" in the following manual.
MR-J5 User's Manual (Function)
Function on positioning operation Absolute position detection/external limit switch/software position limit/
positioning function to the home position, etc.

14 1 SPECIFICATIONS
1.4 Drive unit standard specifications
Functional safety
Drive unit specifications
*1 When DI/O connection (CN8) is used, diagnosis by test pulses is required in order to satisfy Category 4 PL e, SIL 3.
*2 Although the special proof tests within the mission time of the safety sub-function is not needed to be performed, the suggested
diagnostic test interval in IEC 61800-5-2: 2016 is at least one test per three months for Category 3 PL e, SIL 3.
Function specifications
*1 Available functions and safety levels differ depending on the combination of the drive units and the servo motors.
Page 15 List of safety sub-function compatible units
*2 When DI/O connection (CN8) is used, diagnosis by test pulses is required in order to satisfy Category 4 PL e, SIL 3.
*3 This value applies when the transmission interval monitor time is 32.0 ms or less.
*4 For the MR-J5D1-_G_, connect to a network with a communication cycle of 125 μs or longer. For the MR-J5D2-_G_ and the MR-J5D3-
_G_, connect to a network with a communication cycle of 500 μs or longer.
*5 The safety observation speed can be set separately.
*6 A test pulse is a signal which instantaneously turns off a signal to the drive unit at a constant period for external circuits to perform self-
diagnosis.
*7 This specification applies when the safety sub-functions by a network connection is used.
*8 This value applies when the transmission interval monitor time is 64.0 ms or less.
Item Specifications
Safety performance Satisfied standards *1 EN ISO 13849-1:2015 Category 4 PL e, IEC 61508 SIL 3, EN 62061 SIL CL 3, EN
61800-5-2
Mean time to dangerous failure (MTTFd) MTTFd ≥100 [years] (750a)
Diagnostic coverage (DC) DC = Medium, 96.5 [%]
Probability of dangerous Failure per Hour (PFH) PFH = 3 × 10-9 [1/h]
Mission time (TM) *2 TM = 20 [year]
Item Specifications
Safety sub-function
*1 *2
STO Shut-off response time (STO
input off →energy shut off)
8 ms or less (when an input device is used)
60 ms or less (when a network is used) *3 *4 *7
SS1 Deceleration delay time 0 ms to 60000 ms (set by functional safety parameters)
SS2 Deceleration delay time 0 ms to 60000 ms (set by functional safety parameters)
SOS Observation position 0 rev to 1000 rev (set by functional safety parameters)
SBC Shut-off response time 8 ms or less (when an input device is used)
60 ms or less (when a network is used) *3 *4 *7
SLS1/2/3/4 Observation speed 0 r/min (mm/s) to 10000 r/min (mm/s) (set by functional safety parameters) *5
SSM Observation speed 0 r/min (mm/s) to 10000 r/min (mm/s) (set by functional safety parameters)
SDI Direction monitor delay time 0 ms to 60000 ms (set by functional safety parameters)
SLI Observation position 0 rev to 1000 rev (set by functional safety parameters)
SLT Observation torque -1000.0 % to 1000.0 % (set by functional safety parameters)
I/O function Input device Number of inputs 1 point x 2 systems
Permissible time for
mismatched double inputs
0 ms to 60000 ms (set by functional safety parameters)
Noise elimination filter 1.000 ms to 32.000 ms (set by functional safety parameters)
Test pulse off time *6 1 Hz to 25 Hz
Output device Number of outputs 1 point x 2 systems
Test pulse off time *6 0.500 ms to 2.000 ms (set by functional safety parameters)
Test pulse interval *6 Within 1 s
Safety communication function Response time 250 ms *8
Transmission interval monitor
time
16.0 ms to 1000.0 ms (set by functional safety parameters) (when a network is used)
*7
Safety communication delay
time
60 ms or less (when a network is used) *3 *7

1 SPECIFICATIONS
1.4 Drive unit standard specifications 15
1
List of safety sub-function compatible units
*1 Combine the drive unit with a safety programmable controller R_SFCPU that has firmware version 20 or later.
*2 The safety levels in the table apply if the safety sub-function control is performed by a safety programmable controller or a safety
controller that complies with Category 4 PL e, SIL 3. If the drive units are directly connected with emergency stop switches, safety
switches, enabling switches, or other similar devices, the safety level Category 3 PL d, SIL 2 applies.
*3 Fully closed loop control systems do not support SS1-r, SS2, SOS, SLS, SSM, SDI, and SLI.
*4 STO can be set separately for each axis.
*5 For the MR-J5D1-_G_, connect to a network with a communication cycle of 125 μs or longer. For the MR-J5D2-_G_ and the MR-J5D3-
_G_, connect to a network with a communication cycle of 500 μs or longer.
*6 When DI/O connection (CN8) is used, diagnosis by test pulses is required in order to satisfy Category 4 PL e, SIL 3.
*7 The safety sub-function by a network connection cannot be used with CC-Link IE Field Network Basic.
Drive unit Function
achieving
method
(wiring
destination)
Servo motor type Safety sub-function (IEC/EN 61800-5-2)
STO SS1 SS2 *3 SOS
*3
SBC SLS
*3
SSM
*3
SDI
*3
SLI
*3
SLT
SS1-
t
SS1-
r *3
SS2-t,
SS2-r
MR-J5D1-
_G_
MR-J5D2-
_G_ *4
MR-J5D3-
_G_ *4
DI/O
connection *2
*6 (CN8)
Servo motor with
functional safety
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
3PL d,
SIL 2
Rotary servo motor
Linear servo motor
Direct drive motor
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
3PL d,
SIL 2
Cat.
4PL e,
SIL 3
Cat.
3PL d,
SIL 2
Cat.
3PL d,
SIL 2
Cat.
3PL d,
SIL 2
Cat.
3PL d,
SIL 2
Network
connection *1
*5 *7 (CN1A/
CN1B)
Servo motor with
functional safety
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
3PL d,
SIL 2
Rotary servo motor
Linear servo motor
Direct drive motor
Cat.
4PL e,
SIL 3
Cat.
4PL e,
SIL 3
Cat.
3PL d,
SIL 2
Cat.
4PL e,
SIL 3
Cat.
3PL d,
SIL 2
Cat.
3PL d,
SIL 2
Cat.
3PL d,
SIL 2
Cat.
3PL d,
SIL 2

16 1 SPECIFICATIONS
1.4 Drive unit standard specifications
Environment
*1 Refer to "Restrictions when using this product at altitude exceeding 1000 m and up to 2000 m" in the following manual for using the
product at altitude exceeding 1000 m.
MR-J5D User's Manual (Hardware)
Item Operation Transportation Storage
Ambient temperature 0 ˚C to 60 ˚C (non-freezing)
Class 3K3 (IEC 60721-3-3)
-25 ˚C to 70 ˚C (non-freezing)
Class 2K12 (IEC 60721-3-2)
-25 ˚C to 70 ˚C (non-freezing)
Class 1K4 (IEC 60721-3-1)
Ambient humidity 5 %RH to 95 %RH (non-condensing) 5 %RH to 95 %RH (non-condensing) 5 %RH to 95 %RH (non-condensing)
Ambience Indoors (no direct sunlight); no corrosive gas, inflammable gas, oil mist or dust
Altitude/atmospheric
pressure
Altitude: 2000 m or less *1 Transportation conditions: Must be
transported by ground/sea, or air at an
atmospheric pressure of 700 hPa or
more.
Atmospheric pressure: 700 hPa to 1060
hPa
(equivalent to the altitude of -400 m to
3000 m.)
Vibration resistance Under intermittent vibration:
10 Hz to 57 Hz, displacement amplitude
0.075 mm
57 Hz to 150 Hz, acceleration amplitude
9.8 m/s2
Class 3M1 (IEC 60721-3-3)
Under continuous vibration (in each of
the X, Y, and Z directions): 10 Hz to 55
Hz, acceleration amplitude 5.9 m/s2
2 Hz to 9 Hz, displacement amplitude
(half amplitude) 7.5 mm
9 Hz to 200 Hz, acceleration amplitude
20 m/s2
Class 2M3 (IEC 60721-3-2)
2 Hz to 9 Hz, displacement amplitude
(half amplitude) 1.5 mm
9 Hz to 200 Hz, acceleration amplitude 5
m/s2
Class 1M2 (IEC 60721-3-1)
Dielectric
strength
400 V
class
Between main circuit (power supply/power terminal) and PE: 2000 V AC, 1 minute, 50 Hz/60 Hz
Insulation resistance Between main circuit (power supply/power terminal) and PE: 0.5 MΩor more (with a 500 V DC megger)

1 SPECIFICATIONS
1.5 Function block diagram 17
1
1.5 Function block diagram
The following shows the function block diagram of this drive unit.
MR-J5D1-_G_
400 V class
*1 Drive units with the rated output symbol of 500 (MR-J5D1-500G4_) or greater have a cooling fan.
L11
L21
L+
MCCB
MCCB
U
V
W
E
+
CN4
M
CN2A CNP3A
CN8
CN40A
CN2AL
CN5
USB
USB
CN1A CN1B
D/A
CN3
L-
CN40B
Servo motor
Dynamic brake
circuit
Current
detector
Power
supply Cooling fan *1
Control
circuit
power supply
STO
Control
circuit
STO
switch
Encoder
Overcurrent
protection
Base amplifier
Current
detection
Step-
down
circuit
Control engine
I/F control
Personal
computer Digital I/O
control
Network Network
Analog monitor
(2 channels)
Drive unit
From L+ of converter
unit
From L- of converter
unit
To the main
circuit power
supply input
of the
converter
unit
External encoder
From CN4 of converter
unit or CN40B of drive
unit
To CN40A of drive unit

18 1 SPECIFICATIONS
1.5 Function block diagram
MR-J5D2-_G_/MR-J5D3-_G_
400 V class
The following is an example using MR-J5D3-_G_.
*1 Drive units other than MR-J5D2-100G4_ and MR-J5D3-100G4_ have a cooling fan.
U
V
W
E
U
V
W
E
U
V
W
E
M
E
M
E
M
E
TRM (A)
L+
L-
MCCB
CNP3A
CN2ACNP3B
CN2B
CNP3CCN2CCN4
CN3 CN5
USB
L11
L21
CN8CN1ACN1B
+
*1
CN40ACN40B
MCCB
A-axis
servo motor
A-axis
output
Current
detector
Power
supply
Dynamic
brake circuit A A-axis
F/B
Cooling fan
STO circuit
Control
circuit
power
supply
B-axis
servo motor
Base
amplifier
Current
detection A
Overvoltage Overcurrent
A
B-axis
output
Control engine
STO switch
B-axis
F/B
Controlling B-axis
Network C-axis
servo motor
Controlling C-axis
C-axis
output
I/F
control
Network
C-axis
F/B
Step-
down
circuit
Digital I/O
control
Analog
output Personal
computer
From L+ of converter unit
From L- of converter unit
To the main circuit power supply
input of the converter unit
From CN4 of converter
unit or CN40B of drive
unit
To CN40A of drive unit
Drive unit