Mitsubishi Electric R12A-D Series User manual

PROPELLER FAN
Wear gloves when cleaning or maintenance
Do not rotate the propeller fan counterclockwise
because the PCB will damage
The propeller fan should be removed if there is a risk
that the propeller fan will rotate in wrong direction
( In case carry on the pickup truck or motorcycle )
( The PCB will damage if rotate the propeller fan in
wrong direction at speed over 1500 rpm )
Do not start the fan while removing propeller fan or guard
( Propeller fan might be damaged and cause injury )
Do not place objects or a fan over the power cord
The power cord will be damaged / Burning or Short circuit parts ( May be injured if do not wear gloves )
PROPELLER
LOCK
FRONT
GUARD
REAR GUARD
LOCK
GUARD CLIP
REAR
GUARD
UNLOCK
BUTTON
FAN BASE
CONTROL BUTTON
OPERATION CONTROL
REMOTE RECEIVER
REMOTE CONTROL
The packing position in the carton boxis in Page 8
LITHIUM BATTERY
BATTERYIN BAG WITH
REMOTE CONTROL
REMOTE SLOT
CORD
PLUG
START-STOP FUNCTION NATURAL
WIND
START-STOP CHILD LOCK MODE
DISPLAY A LEVEL OF WIND SPEED
STOPPING TIME SETTING
STARTING TIME SETTING
WIND SPEED LEVEL CONTROL
START-STOP SWING UP AND DOWN
START-STOP SWING LEFT AND RIGHT
START-STOP FAN OPERATI NG
TURN OFF LED LIGHT AND SOUND
V. S WING (VERTICAL)
LED SPEED
SPEED
H.SWING (HORIZONTAL)
SWING DIRECTION (HORIZONTAL)
CHANGE THE DIRECTION
LEFT, RIGHT AND STOP SWING
LEFT- RIGHT
REMOTE CONTROL OPERATION
ON/OFF
SEE PAGE. 4
SEE PAGE. 4
SEE PAGE. 4
SEE PAGE. 4
SEE PAGE. 5
SEE PAGE. 6
SEE PAGE. 4
SEE PAGE. 8
SEE PAGE. 6
SEE PAGE. 6
SEE PAGE. 6
MIDDLE
PIPE
MOTOR
HANDLE
PIN
SLOT

ASSEMBLY
USAGE
PLUG CONNECTION
REMOTECONTROL AND BATTERY
FAN OPERATION AND REMOTE CONTROL
How to install Lithium battery
Press the tip pen to rear hold and slide along arrow direction
Press remote control button and checking LED display.
Control function of fan must be same with remote control.
Press on a center of remote control button
Turn the direction of remote sensor
to match with signal receiver
Child lock function , Turn off LED light and sound cannot control
by remote.
Change direction function by remote control.
Put the battery cover out
Put the Lithium battery in and always keep over cover
Pull cover untill “click ”sound
HIGH POSITION ASSEMBLY
CAUTION
CAUTION
LOW POSITION ASSEMBLY
Remove a pipe cap from the Motor , Middle pipe , Base
Unplug the fan before assembly the Motor , Middle pipe , Base
Take a fan handle on a motor cover
During to assembly. Do not adjust the degree of fan by hand
Insert a middle pipe before the motor ( in case the high position assembly )
removed the motor first ( in case of disassembly )
Do not insert fingers or objects into the guard and moving parts
( might be damaged and injury )
Do not take a face near the rear guard
A fan has sound “Beep” when the plug connected.
When the plug connected, the bases will warm up even the fan switch off because its has current
~ 2 Watt
in a PCB
Insert pin into slot
There are difference pin size ( Cannot assemble if the pin diameter not match with slot )
PIPE CAP
HANDLE
MOTOR
SUITABLE FOR
COOLING SUITABLE FOR
AIR FLOW
HANDLE
PIN
PIN
SLOT
SLOT
UNLOCK BUTTON
PRESS UNLOCK BUTTON
AND PULL UP
UNLOCK
BUTTON
MIDDLE PIPE
BASE
REMOTE CONTROL LITHIUM
BATTERY
BATTERY
COVER
BACK
PEN
UNLOCK HOLE
OPERATING CONTROL BUTTON
SIGNAL RECEIVER
REMOTE CONTROL BUTTON
BASE
PIPE CAP

START - STOP OPERATION
SPEED CONTROL
5 Levels speed control
Press
AND
Press
Time setting always change, after press the button.
LED OFF timer appear , OFF timer function start operating
START
STOP
Start natural wind mode LED
LED
appear
Stop natural wind mode LED disappear
for increase wind speed Press for decrease wind speed
LED light display a level of current speed
Press
when the propeller fan was locked
Motor lock function
Press button
Press button
again
Fan start operating ,
LED SPEED display
Fan stop operating ,
LED SPEED disappear
Remote sensor
Signal receiver
min
AIR VOLUME
VARIABLE AIR VOLUME
TIME
TIME CHANGE
min
min
min
hr
hr
hr
hr
min
hr
hr
hr
LED disply at
Sleep and Number
LED disappear
timer off canclled
LED display
only Number

-1
-2
Do not touch the propeller fan or guard
while the fan is on timer mode

LED light
disappear
Stop oscillation
Press H.SWING
HORIZONTAL SWING
While start the horizontal swing , Fan might be stop moving for set the position
When connecting plug and press swing button , Fan will moving backto start at the center axis
button to turn on oscillation LED light display at the oscillation degree

CHANGE DIRECTION
While operating in H.swing mode,
press
The fan will swing Left or Right 10
or button at the remote control.
While the normal operating ,
press
The fan will swing Left or Right 10
or button at the remote control.
VERTICAL SWING
Horizontal axis
Before
HANDLE
REMOTE CONTROL STORAGE
Keep the remote control in BASE SLOT Take handle at the motor cover
BASE SLOT
HANDLE
REMOTE
CONTROL
Press button
While change the direction,
Fan will stop for setting
the position
Swing adjustment limit at
( from front )
MOTOR COVER
DO NOT
ROTATE
BY HAND
Start vertical oscillation, LED light dispaly
Cannot change direction at
Before
Front
After
After
LED light
disappear
Stop oscillation
While start the vertical swing , Fan might be stopped moving for setting the position.
USAGE

MAINTAINING AND PACKING
Please make sure unplug the fan before
cleaning
MAINTAINANCE
Assembly and maintainance, please do
according to the manual
REAR GUARD
Take the front guard out of the
rear guard by releasing the
guard clip and prying the guard
lock until latches separated
Then remove the front guard
Remove the
Propeller lock by
turn its clockwise
Remove the propeller
fan from rotor shaft
Remove the rear guard
lock by rotate
counter clockwise
FRONT GUARD
GUARDCLIP
PROPELLER
LOCK
PROPELLER FAN
MOTOR SHAFT
GROOVE GROOVE
REAR GUARD
LOCK
REAR GUARD
MARK
MARK MARK
LATCH
Wear gloves when cleaning
or parts maintenance
(May be injured if do not wear gloves )

MOTOR
CAUTION
PIPE CAP
PACKING
PIPE CAP
RIFT
RIFT
FAN BASE
( The product or parts might be damaged )
Do not transport the product in a fanless condition. In transit, please store in a carton box
Tur n the motor to alignment , moving up and down
Put the fan base in a carton box
Put remote control in the carton box
Should be stored in dry place
Put the motor on a motor spacer and alignment with middle pipe box
Put the middle pipe into a carton box ( between rift of base spacer and motor spacer )
Put the Base spacer and Motor spacer in the carton box
Put a pipe cap into the motor pipe , middle pipe and lower pipe
After that put all parts into the plastic bag
Pull the plug out of the receptance , Then remove the motor from a middle pipe
( See page. 3 )
HOW TO PACK
CARTON BOX BASE SPACER
MOTOR SPACER
MIDDLE PIPE
MIDDLE PIPE BOX
MOTOR PIPE
LOWER PIPE
REMOTE CONTROL