Mitsubishi AJ65SBT2B-64AD User manual

A- 1
SAFETY PRECAUTIONS
(Read these precautions before using this product.)
Before using this product, please read this manual and the relevant manuals carefully and pay full attention
to safety to handle the product correctly.
The precautions given in this manual are concerned with this product only. For the safety precautions of the
programmable controller system, refer to the user's manual for the CPU module used.
In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".
Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to
serious consequences.
Observe the precautions of both levels because they are important for personal and system safety.
Make sure that the end users read this manual and then keep the manual in a safe place for future
reference.
[Design Precautions]
WARNING
●In the case of a communication failure in the network, data in the master module are held.
Check the communication status information and configure an interlock circuit in the sequence
program to ensure that the entire system will operate safely.
●Do not use any "use prohibited" signals as a remote input or output signal. These signals are
reserved for system use. If they are turned on/off by a user, correct operation of the module cannot
be guaranteed.
CAUTION
●Do not install the control lines or communication cables together with the main circuit lines or power
cables.
Keep a distance of 100mm or more between them.
Failure to do so may result in malfunction due to noise.
WARNING
CAUTION
Indicates that incorrect handling may cause hazardous conditions,
resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions,
resulting in minor or moderate injury or property damage.

A- 2
[Installation Precautions]
[Wiring Precautions]
CAUTION
●Use the module in an environment that meets the general specifications in this manual.
Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of the
product.
●For protection of the switches, do not remove the cushioning material before installation.
●Securely fix the module with a DIN rail or mounting screws. Tighten the screws within the specified
torque range.
Undertightening can cause drop of the screw, short circuit or malfunction.
Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.
●Do not directly touch any conductive part of the module.
Doing so can cause malfunction or failure of the module.
WARNING
●Shut off the external power supply (all phases) used in the system before wiring.
Failure to do so may result in malfunction or damage to the product.
CAUTION
●Ground the FG terminal to the protective ground conductor dedicated to the programmable
controller.
Failure to do so may result in electric shock or malfunction.
●Tighten any unused terminal screws within the specified torque range (0.42 to 0.50N•m). Failure to
do so may cause a short circuit.
●Use applicable solderless terminals and tighten them within the specified torque range.
If any spade solderless terminal is used, it may be disconnected when the terminal screw comes
loose, resulting in failure.
●Check the rated voltage and terminal layout before wiring to the module, and connect the cables
correctly.
Applying a voltage or inputting a current that exceeds the absolute maximum input of the module,
connecting a power supply with a different voltage rating, or wiring the cables incorrectly may cause
a fire or failure.
●Tighten the terminal screw within the specified torque range.
Undertightening can cause short circuit, fire, or malfunction.
Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.

A- 3
[Wiring Precautions]
[Startup and Maintenance Precautions]
CAUTION
●Prevent foreign matter such as dust or wire chips from entering the module.
Such foreign matter can cause a fire, failure, or malfunction.
●Place the cables in a duct or clamp them.
If not, dangling cable may swing or inadvertently be pulled, resulting in damage to the module or
cables or malfunction due to poor contact.
●Do not install the control lines or communication cables together with the main circuit lines or power
cables.
Doing so may result in malfunction due to noise.
●When disconnecting the cable from the module, do not pull the cable by the cable part.
Loosen the screws of connector before disconnecting the cable.
Failure to do so may result in damage to the module or cable or malfunction due to poor contact.
WARNING
●Do not touch any terminal while power is on.
Doing so will cause electric shock or malfunction.
●Shut off the external power supply (all phases) used in the system before cleaning the module or
retightening the terminal screws or module mounting screws.
Failure to do so may cause the module to fail or malfunction.
Undertightening can cause drop of the screw, short circuit or malfunction.
Overtightening can damage the screw and/or module, resulting in drop, short circuit, or malfunction.

A- 4
[Startup and Maintenance Precautions]
[Disposal Precaution]
CAUTION
●Do not disassemble or modify the module.
Doing so may cause failure, malfunction, injury, or a fire.
●Use any radio communication device such as a cellular phone or PHS (Personal Handy-phone
System) more than 25cm away in all directions from the module.
Failure to do so may cause malfunction.
●Do not drop or apply strong shock to the module.
Doing so may damage the module.
●Shut off the external power supply for the system in all phases before installing or removing a
module to/from a control panel.
Failure to do so may cause the module to fail or malfunction.
●After the first use of the product, do not mount/remove the terminal block to/from the module more
than 50 times (IEC 61131-2 compliant).
Exceeding the limit of 50 times may cause malfunction.
●Before handling the module, touch a grounded metal object to discharge the static electricity from
the human body. Failure to do so may cause the module to fail or malfunction.
CAUTION
●When disposing of this product, treat it as industrial waste.

A- 5
CONDITIONS OF USE FOR THE PRODUCT
(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;
i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major
or serious accident; and
ii) where the backup and fail-safe function are systematically or automatically provided outside of
the PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.
(2) The PRODUCT has been designed and manufactured for the purpose of being used in general
industries.
MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT
LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT,
WARRANTY, TORT, PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR
LOSS OR DAMAGE TO PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR
USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS,
OR WARNING CONTAINED IN MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY
MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.
("Prohibited Application")
Prohibited Applications include, but not limited to, the use of the PRODUCT in;
• Nuclear Power Plants and any other power plants operated by Power companies, and/or any
other cases in which the public could be affected if any problem or fault occurs in the PRODUCT.
• Railway companies or Public service purposes, and/or any other cases in which establishment of
a special quality assurance system is required by the Purchaser or End User.
• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as
Elevator and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation,
Equipment for Recreation and Amusement, and Safety devices, handling of Nuclear or
Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where there is a
significant risk of injury to the public or property.
Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the
PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT
is limited only for the specific applications agreed to by Mitsubishi and provided further that no
special quality assurance or fail-safe, redundant or other safety features which exceed the general
specifications of the PRODUCTs are required. For details, please contact the Mitsubishi
representative in your region.

A- 6
REVISIONS
* The manual number is given on the bottom left on the back cover.
Japanese manual version SH-080965-A
2011 MITSUBISHI ELECTRIC CORPORATION
Print date *Manual number Revision
May, 2011 SH(NA)-080979ENG-A First edition
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.
Mitsubishi Electric Corporation cannot be held responsible for any problem involving industrial property rights which may
occur as a result of using the contents noted in this manual.

A- 7
INTRODUCTION
Thank you for purchasing the Mitsubishi programmable controllers.
Before using this product, please read this manual carefully and develop familiarity with the functions and
performance of the programmable controller to handle the product correctly.
CONTENTS
SAFETY PRECAUTIONS .................................................................................................................................A - 1
CONDITIONS OF USE FOR THE PRODUCT..................................................................................................A - 5
REVISIONS.......................................................................................................................................................A - 6
INTRODUCTION...............................................................................................................................................A - 7
CONTENTS ......................................................................................................................................................A - 7
MANUALS.........................................................................................................................................................A - 9
COMPLIANCE WITH THE EMC AND LOW VOLTAGE DIRECTIVES............................................................. A - 9
GENERIC TERMS AND ABBREVIATIONS....................................................................................................A - 10
PACKING LIST ...............................................................................................................................................A - 11
CHAPTER 1 OVERVIEW 1 - 1 to 1 - 2
1.1 Features........................................................................................................................................... 1 - 1
CHAPTER 2 SYSTEM CONFIGURATION 2 - 1 to 2 - 2
2.1 Overall Configuration ....................................................................................................................... 2 - 1
2.2 Applicable System ........................................................................................................................... 2 - 2
2.3 Checking the Hardware Version ...................................................................................................... 2 - 2
CHAPTER 3 SPECIFICATIONS 3 - 1 to 3 - 21
3.1 General Specifications..................................................................................................................... 3 - 1
3.2 Performance Specifications ............................................................................................................. 3 - 2
3.3 I/O Conversion Characteristics ........................................................................................................ 3 - 3
3.3.1 Voltage input characteristics..................................................................................................... 3 - 4
3.3.2 Current input characteristics ..................................................................................................... 3 - 6
3.3.3 Accuracy................................................................................................................................... 3 - 8
3.3.4 Conversion speed..................................................................................................................... 3 - 8
3.4 Functions ......................................................................................................................................... 3 - 9
3.4.1 Function list .............................................................................................................................. 3 - 9
3.4.2 A/D conversion enable/disable function ................................................................................. 3 - 10
3.4.3 Sampling processing/average processing specification ......................................................... 3 - 11
3.4.4 Input range setting function .................................................................................................... 3 - 15
3.5 Remote I/O Signals........................................................................................................................ 3 - 16
3.5.1 List of remote I/O signals........................................................................................................ 3 - 16
3.5.2 Details on each remote I/O signal ..........................................................................................3-17
3.6 Remote Register............................................................................................................................ 3 - 21
3.6.1 List of remote register assignments........................................................................................3-21
3.6.2 Details of remote register ....................................................................................................... 3 - 21

A- 8
CHAPTER 4 SETTINGS AND THE PROCEDURE BEFORE OPERATION 4 - 1 to 4 - 14
4.1 The Procedure Before Operation..................................................................................................... 4 - 1
4.2 Handling Precautions....................................................................................................................... 4 - 2
4.3 Part Names ...................................................................................................................................... 4 - 4
4.3.1 Transmission speed auto-tracking function .............................................................................. 4 - 7
4.4 Station Number Setting.................................................................................................................... 4 - 8
4.5 Module Mounting Direction .............................................................................................................. 4 - 8
4.6 Wiring of Data Link Cables .............................................................................................................. 4 - 9
4.6.1 Wiring precautions .................................................................................................................... 4 - 9
4.6.2 Connecting modules using CC-Link dedicated cables ............................................................. 4 - 9
4.6.3 Connecting terminating resistors .............................................................................................. 4 - 9
4.7 Wiring with External Devices ......................................................................................................... 4 - 10
4.7.1 Wiring precautions .................................................................................................................. 4 - 10
4.7.2 Wiring with external devices ................................................................................................... 4 - 11
4.8 Offset/Gain Setting ........................................................................................................................ 4 - 12
4.9 Maintenance and Inspection .......................................................................................................... 4 - 14
CHAPTER 5 PROGRAMMING 5 - 1 to 5 - 24
5.1 Programming Procedure.................................................................................................................. 5 - 1
5.2 Conditions of Program Examples .................................................................................................... 5 - 2
5.3 Program Example When Using the QCPU (Q mode) ...................................................................... 5 - 4
5.4 Program Example When Using the LCPU ....................................................................................... 5 - 9
5.5 Program Example When Using the QnACPU................................................................................ 5 - 12
5.6 Program Example When Using the ACPU/QCPU (A mode) (Dedicated Instructions) .................. 5 - 17
5.7 Program Example When Using the ACPU/QCPU (A mode) (FROM/TO Instructions) .................. 5 - 21
CHAPTER 6 TROUBLESHOOTING 6 - 1 to 6 - 7
6.1 Error Check Method by the LED Display ......................................................................................... 6 - 1
6.2 When the Digital Output Value Cannot Be Read ............................................................................. 6 - 4
6.3 When the Data Link Needs a Lot of Time ........................................................................................ 6 - 4
6.4 Troubleshooting When the ERR. LED of the Master Station Flashes ............................................. 6 - 5
6.5 When Hardware Error Flag (RXnA) Turns on.................................................................................. 6 - 7
6.6 When User Range Read Error Flag (RXnB) Turns on..................................................................... 6 - 7
6.7 When Flash Memory Write Error Flag (RXnC) Turns on ................................................................. 6 - 7
6.8 When Number of Offset/Gain Settings Excess Flag (RXnD) Turns on............................................ 6 - 7
APPENDIX App - 1 to App - 2
Appendix 1 External Dimensions.........................................................................................................App - 1
INDEX INDEX - 1 to INDEX - 2

A- 9
MANUALS
The manuals related to this product are listed below.
Please place an order as needed.
COMPLIANCE WITH THE EMC AND LOW VOLTAGE DIRECTIVES
(1) Method of ensuring compliance
To ensure that Mitsubishi programmable controllers maintain EMC and Low Voltage
Directives when incorporated into other machinery or equipment, certain measures
may be necessary. Please refer to the "EMC AND LOW VOLTAGE DIRECTIVES"
chapter of the User's Manual for the CPU module used.
The CE mark on the side of the programmable controller indicates compliance with
EMC and Low Voltage Directives.
(2) Additional measures
To ensure that this product maintains EMC and Low Voltage Directives, please refer
to the "CC-Link module" section in the "EMC AND LOW VOLTAGE DIRECTIVES"
chapter in the user's manual for the CPU module used.
Relevant manuals
Manual name Manual number
(model name)
CC-Link System Master/Local Module Type AJ61BT11/A1SJ61BT11 User's Manual
System configuration, performance specifications, functions, handling, wiring, and troubleshooting of the AJ61BT11
and A1SJ61BT11
(Sold separately)
IB-66721
(13J872)
CC-Link System Master/Local Module Type AJ61QBT11/A1SJ61QBT11 User's Manual
System configuration, performance specifications, functions, handling, wiring, and troubleshooting of the
AJ61QBT11 and A1SJ61QBT11
(Sold separately)
IB-66722
(13J873)
Type AnSHCPU/AnACPU/AnUCPU/QCPU-A (A Mode) Programming Manual (Dedicated Instructions)
Instructions extended for the AnSHCPU/AnACPU/AnUCPU
(Sold separately)
IB-66251
(13J742)
CC-Link System Master/Local Module User's Manual
System configuration, performance specifications, functions, handling, wiring, and troubleshooting of the CC-Link
module
(Sold separately)
SH-080394E
(13JR64)
MELSEC-L CC-Link System Master/Local Module User's Manual
System configuration, performance specifications, functions, handling, wiring, and troubleshooting of the L26CPU-
BT and LJ61BT11
(Sold separately)
SH-080895ENG
(13JZ41)

A- 10
GENERIC TERMS AND ABBREVIATIONS
Unless otherwise specified, the following generic terms and abbreviations are used in this manual to describe the
AJ65SBT2B-64AD analog-digital converter module.
Generic term/
abbreviation Description
GX Developer The product name of the software package for the MELSEC programmable controllers
GX Works2
Programming tool A generic term for GX Works2 and GX Developer
ACPU
A generic term for the following CPU modules: A0J2CPU, A0J2HCPU, A1CPU, A2CPU,
A2CPU-S1, A3CPU, A1SCPU, A1SCPUC24-R2, A1SHCPU, A1SJCPU, A1SJCPU-S3,
A1SJHCPU, A1NCPU, A2NCPU, A2NCPU-S1, A3NCPU, A3MCPU, A3HCPU, A2SCPU,
A2SHCPU, A2ACPU, A2ACPU-S1, A3ACPU, A2UCPU, A2UCPU-S1, A2USCPU, A2USCPU-S1,
A2USHCPU-S1, A3UCPU, and A4UCPU
QnACPU A generic term for the following CPU modules: Q2ACPU, Q2ACPU-S1, Q2ASCPU, Q2ASCPU-S1,
Q2ASHCPU, Q2ASHCPU-S1, Q3ACPU, Q4ACPU, and Q4ARCPU
QCPU (A mode) A generic term for the Q02CPU-A, Q02HCPU-A, and Q06HCPU-A
QCPU (Q mode)
A generic term for the following CPU modules: Q00JCPU, Q00CPU, Q01CPU, Q02CPU,
Q02HCPU, Q06HCPU, Q12HCPU, Q25HCPU, Q02PHCPU, Q06PHCPU, Q12PHCPU,
Q25PHCPU, Q12PRHCPU, Q25PRHCPU, Q00UJCPU, Q00UCPU, Q01UCPU, Q02UCPU,
Q03UDCPU, Q04UDHCPU, Q06UDHCPU, Q10UDHCPU, Q13UDHCPU, Q20UDHCPU,
Q26UDHCPU, Q03UDECPU, Q04UDEHCPU, Q06UDEHCPU, Q10UDEHCPU, Q13UDEHCPU,
Q20UDEHCPU, Q26UDEHCPU, Q50UDEHCPU, and Q100UDEHCPU
LCPU A generic term for the L02CPU and L26CPU-BT
Master station A station that controls a data link system.
One master station is required for one system.
Local station A station that includes a CPU module and can communicate with the master station and other local
stations
Remote I/O station A station, such as AJ65BTB1-16D and AJ65SBTB1-16D, that exchanges I/O signals (bit data) with
an external device
Remote device station A station that exchanges I/O signals (bit data) and I/O data (word data) with an external device, and
converts analog data into digital data
Remote station A generic term for a remote I/O station and a remote device station
Intelligent device
station
A station, such as the AJ65BT-R2N, that can perform transient transmission.
Local stations are included.
Master module A generic term for modules that can serve as a master station
SB
Link special relay (for CC-Link)
Bit data that indicates the operating status and data link status of modules on the master and local
stations
SW
Link special register (for CC-Link)
Word data that indicates the operating status and data link status of modules on the master and
local stations
RX Remote input (for CC-Link)
Bit data input from a remote station to the master station
RY Remote output (for CC-Link)
Bit data output from the master station to a remote station
RWw Remote register (write area for CC-Link)
Word data output from the master station to a remote device station
RWr Remote register (read area for CC-Link)
Word data input from a remote device station to the master station

A- 11
PACKING LIST
The following items are included in the package of this product.
Product Quantity
AJ65SBT2B-64AD analog-digital converter module 1
Analog-Digital Converter Module User's Manual (Hardware) Type AJ65SBT2B-64AD 1

1- 1 1.1 Features
1OVERVIEW
CHAPTER 1 OVERVIEW
This user's manual explains the specifications, operations, and programming method of
the AJ65SBT2B-64AD analog-digital converter module (hereafter abbreviated as
AJ65SBT2B-64AD) used as a remote device station of a CC-Link system.
The AJ65SBT2B-64AD changes analog values (voltage or current) to digital values (16-bit
signed binary).
1.1 Features
This section describes the features of the AJ65SBT2B-64AD.
(1) A/D conversion by one module with 4 channels
One module enables an A/D conversion with 4 channels.
(2) Input range setting for each channel
I/O conversion characteristics can be changed by setting an analog input range in
each channel.
(3) Response by high-speed conversion
High-speed conversion of 200µs/channel is achieved.
(4) High resolution
In all analog input ranges, high resolution of 1/16000 is achieved.
(5) High accuracy
The module performs an A/D conversion in accuracy of ±0.2%*1 at the maximum
digital output value when the operating ambient temperature is within 0 to 55°C.
* 1 Except when receiving noise influence.
(6) Selecting the conversion method
A conversion processing method for each channel can be selected from the sampling
processing, time average processing, count average processing or moving average
processing.
(7) Saving man-hour
(a) Since the module has a built-in terminating resistor (110Ω), a terminating resistor
is not necessary when the module is used on the network terminal. In addition,
one operation with a switch can make the built-in terminating resistor invalid.
(b) The transmission speed need not be set by the user since it is automatically
determined according to the transmission speed set in a master station.
(c) The offset/gain setting can be configured by simple operations without the
connection to the master module.

1OVERVIEW
1.1 Features 1- 2
1
OVERVIEW
2
SYSTEM CONFIGURATION
3
SPECIFICATIONS
4
SETTINGS AND THE PROCEDURE BEFORE OPERATION
5
PROGRAMMING
6
TROUBLESHOOTINGAPPENDIXINDEX
(8) Connection with up to 42 modules
A master station can connect with up to 42 AJ65SBT2B-64ADs.
(9) Easy maintenance
The structure of the two-piece terminal block enables the user to remove a terminal
block with wiring unchanged for easy maintenance.

2- 1 2.1 Overall Configuration
2SYSTEM CONFIGURATION
CHAPTER 2 SYSTEM CONFIGURATION
This chapter describes the system configuration when using the AJ65SBT2B-64AD.
2.1 Overall Configuration
The following Figure 2.1 shows an overall configuration when using the AJ65SBT2B-
64AD.
Figure 2.1 Overall configuration when using the AJ65SBT2B-64AD
CC-Link system master/local module (master station) CC-Link system master/local module (local station)
CC-Link dedicated cable
(Intelligent device station)
Terminating resistor
Terminating resistor
Device to which a voltage is applied or
through which a current is passed
AJ65SBT2B-64AD
(Remote device station)
Occupies one station.
(Remote device station)
(Remote I/O station)

2SYSTEM CONFIGURATION
2.2 Applicable System 2- 2
1
OVERVIEW
2
SYSTEM CONFIGURATION
3
SPECIFICATIONS
4
SETTINGS AND THE PROCEDURE BEFORE OPERATION
5
PROGRAMMING
6
TROUBLESHOOTINGAPPENDIXINDEX
2.2 Applicable System
The applicable master modules are described in the website of CC-Link Partner
Association (CLPA). Refer to the following URL for the website of CC-Link Partner
Association (CLPA).
http://www.cc-link.org/
Remark
Before using the module, check the specifications of the master module made by
each manufacturer.
(1) Restrictions to use the dedicated instruction for CC-Link (RLPA, RRPA)
The dedicated instruction (RLPA, RRPA) for CC-Link may not be available depending
on the CPU module or master module to be used.
Refer to the following manuals for details on restrictions:
• User's manual for an A series master module
• Type AnSHCPU/AnACPU/AnUCPU/QCPU-A(A Mode) Programming Manual
(Dedicated Instructions)
Any dedicated instructions except RLPA or RRPA are not applicable for the
AJ65SBT2B-64AD.
Refer to Section 5.6 for an example of the program using the dedicated instructions
(RLPA and RRPA).
2.3 Checking the Hardware Version
The hardware version of the AJ65SBT2B-64AD can be checked in the DATE section on
the rating plate.
Figure 2.2 Checking the hardware version
Date of manufacture
Hardware version
Software version
Relevant regulation
standards

3- 1 3.1 General Specifications
3SPECIFICATIONS
CHAPTER 3 SPECIFICATIONS
This chapter describes the specifications of the AJ65SBT2B-64AD.
3.1 General Specifications
This section lists the general specifications of the AJ65SBT2B-64AD.
* 1 Do not use or store the programmable controller under pressure higher than the atmospheric
pressure of altitude 0m. Doing so may cause malfunction.
When using the programmable controller under pressure, please consult your local Mitsubishi
representative.
* 2 This indicates the section of the power supply to which the equipment is assumed to be
connected between the public electrical power distribution network and the machinery within
premises.
Category II applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the rated voltage of 300V is 2500V.
* 3 This index indicates the degree to which conductive material is generated in terms of the
environment in which the equipment is used.
Pollution level 2 is when only non-conductive pollution occurs. A temporary conductivity caused
by condensing must be expected occasionally.
Table 3.1 General specifications
Item Specifications
Operating ambient
temperature 0 to 55°C
Storage ambient
temperature -20 to 75°C
Operating ambient
humidity 10 to 90%RH, non-condensing
Storage ambient
humidity 10 to 90%RH, non-condensing
Vibration resistance
Compliant with
JIS B 3502 and
IEC 61131-2
Frequency Constant
acceleration Half amplitude Number of sweeps
Under
intermittent
vibration
5 to 9Hz - 3.5mm 10 times each in
X, Y, and Z
directions
9 to 150Hz 9.8m/s2-
Under continuous
vibration
5 to 9Hz - 1.75mm
-
9 to 150Hz 4.9m/s2-
Shock resistance Compliant with JIS B 3502 and IEC 61131-2 (147m/s2, 3 times each in X, Y, and Z directions)
Operating
atmosphere No corrosive gases
Operating altitude*1 2000m or less
Installation location Inside a control panel
Overvoltage
category*2 II or lower
Pollution degree*3 2 or less

3SPECIFICATIONS
3.2 Performance Specifications 3- 2
1
OVERVIEW
2
SYSTEM CONFIGURATION
3
SPECIFICATIONS
4
SETTINGS AND THE PROCEDURE BEFORE OPERATION
5
PROGRAMMING
6
TROUBLESHOOTINGAPPENDIXINDEX
3.2 Performance Specifications
This section lists the performance specifications of the AJ65SBT2B-64AD.
Table 3.2 Performance specifications
Item AJ65SBT2B-64AD
Analog input
Voltage -10 to 10VDC (Input resistance: 1MΩ)
Current 0 to 20mADC (Input resistance: 250Ω)
Digital output 16-bit signed binary (-16384 to 16383)
I/O characteristics,
resolution, accuracy
(accuracy at the maximum
digital output value)
Conversion speed 200µs/channel
Absolute maximum input Voltage: ±15V Current: ±30mA*3
Number of analog input
points 4 channels
Number of offset/gain setting
times*4 Max. 10,000 times
CC-Link version CC-Link Ver.1.10
CC-Link station type Remote device station
Number of occupied stations 1 station
Connection cable CC-Link dedicated cable
Withstand voltage 500VAC for 1 minute between all power supply and communication system terminals and all analog input
terminals
Insulation method
Between communication system terminal and all analog input terminals: Photocoupler isolation
Between power supply system terminal and all analog input terminals: Transformer insulation
Between input channels: Non-insulation
Noise immunity Noise voltage 500Vp-p, noise width 1µs, noise frequency 25 to 60Hz (DC type noise simulator condition)
Built-in terminating resistor Provided (110Ω)
External
connection
system
Communication
part, module
power supply
part
7-point two-piece terminal block
M3 × 5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
I/O part
18-point two-piece terminal block
M3 × 5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Applicable wire size 0.3 to 2.0mm2
Analog input range Digital output value
Accuracy*1
(ambient temperature:
0 to 55°C)
Resolution
Voltage
-10 to 10V
-16000 to 16000
±0.2%
(±32 digits)
0.625mV
User range setting 1
(-10 to 10V) 0.5mV*2
User range setting 2
(-5 to 5V) 0.25mV*2
0 to 5V
0 to 16000
0.3125mV
1 to 5V 0.25mV
Current
0 to 20mA
0 to 16000
1.25µA
4 to 20mA 1µA
User range setting 2 -16000 to 16000 1µA*2

3- 3 3.3 I/O Conversion Characteristics
3SPECIFICATIONS
* 1 Except when receiving noise influence.
* 2 These values indicate the maximum resolution with user range setting.
* 3 This value indicates a momentary input current value at which the built-in resistor will not be
broken.
* 4 The number of times that the SELECT/SET switch is set to SET in test mode.
3.3 I/O Conversion Characteristics
The I/O conversion characteristics are the gradient of a straight line connecting an offset
value and a gain value when an analog signal (voltage or current input) from outside the
programmable controller is converted to a digital value.
The offset value is an analog input value (voltage or current) which turns 0 as a digital
output value after conversion.
The gain value is an analog input value (voltage or current) which turns 16000 as a digital
output value after conversion.
Applicable solderless
terminal
•RAV1.25-3 (compliant with JIS C 2805) [Applicable wire size: 0.3 to 1.25mm2]
•V2-MS3, RAP2-3SL, TGV2-3N [Applicable wire size: 1.25 to 2.0mm2]
Module mounting screw M4 screw × 0.7mm × 16mm or more (tightening torque range: 0.78 to 1.08 N•m)
Mountable with a DIN rail
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
External power supply
24VDC (20.4 to 28.8VDC)
Inrush current: 16A, 4.0ms or less
Current consumption: 0.12A (24VDC)
Weight 0.25kg
Table 3.2 Performance specifications
Item AJ65SBT2B-64AD