Mitsubishi MELSEC-F FX-50DU-TKS-C User manual

HARDWARE MANUAL
GRAPHIC FX-50DU-TK(S)-C UNITS
MELSEC-F

Foreword
•This manual contains text, diagrams and explanations which will guide the reader in the correct installation
and operation of the FX-50DU-TK(S)-C and should be read and understood before attempting to install or
use the unit.
•If in doubt at any stage during the installation of the FX-50DU-TK(S)-C always consult a professional
electrical engineer who is qualified and trained to the local and national standards. If in doubt about the
operation or use of the FX-50DU-TK(S)-C please consult the nearest Mitsubishi Electric distributor.
•This manual is subject to change without notice.

Under no circumstances will Mitsubishi electric be liable or responsible for any consequential
damage that may arise as a result of the installation of this equipment.
All examples and diagrams shown in this manual are intended only as an aid to understanding the
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of
the product based on these illustrative examples.
Owing to the very great variety in possible application of this equipment, you must satisfy yourself
as to its suitability for your specific application.

GRAPHIC FX-50DU-TK(S)-C UNITS
Hardware Manual
Manual number: JY992D64301
Manual revision: A
Date: January 1997
Graphic FX-50DU-TK(S)-C Units
i

Guidelines for the safety of the user and protection of the
FX-50DU-TK(S)-C units
This manual provides information for the installation and use of the FX-50DU-TK(S)-C
units.The manual has been written to be used by trained and competent personnel.The
definition of such a person or persons is as follows;
a) Anyengineerwhoisresponsiblefortheplanning,designandconstructionofautomatic
equipment using the product associated with this manual should be of a competent
nature, (trained and qualified to the local and national standards required to fulfil that
role). These engineers should be fully aware of all aspects of safety with regards to
automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and
qualified to the local and national standards required to fulfil that job.These engineers
should also be trained in the use and maintenance of the completed product. This
includes being completely familiar with all associated documentation for the said
product. All maintenance should be carried out in accordance with established safety
practices.
c) All operators of the completed product should be trained to use that product in a safe
and co-ordinated manner in compliance to established safety practices.The operators
should also be familiar with all documentation which is connected with the actual
operation of the completed equipment.
Note: the term ‘completed equipment’ refers to a third party constructed device which
contains or uses the product associated with this manual.
Note’s on the symbology used in this manual
At various times through out this manual certain symbols will be used to highlight points
of information which are intended to ensure the users personal safety and protect the
integrity of the equipment. Whenever any of the following symbols are encountered, its
associated note must read and understood. Each of the symbols used will now be listed
with a brief description of its meaning.
Hardware warnings
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property
damage.
3) Indicates a point of further interest or further explanation.
Software warnings
4) Indicates special care must be taken when using this element of software.
5) Indicates a special point of which the user of the associate software element should
be aware.
6) Indicates a point of interest or further explanation.
Graphic FX-50DU-TK(S)-C Units
ii

The following variations of the FX-50DU-TK(S)-C conform to the identified standards;
Graphic FX-50DU-TK(S)-C Units
iii

Table of Contents
1. Introduction
1.1 The Complete Family Of Graphic Data Access Units .........1-2
1.2 Dimensions and Specifications ....................1-3
1.2.1 FX-50DU-TK(S)-C Dimensions .................1-3
1.2.2 Unit Characteristics .......................1-3
1.2.3 Basic Specifications .......................1-3
1.3 Unit Accessories ...........................1-4
1.4 Optional Accessories .........................1-4
1.5 Configuration .............................1-5
1.5.1 Product Description .......................1-5
1.5.2 Connection Details ........................1-5
1.6 Function List ..............................1-6
1.7 Set-up Mode ..............................1-7
2.Terminal Layouts
2.1PowerTerminals............................2-2
2.2 RS232C Connector ..........................2-2
2.3 RS422 Connector ...........................2-2
3. Installation
3.1 Product Outline ............................3-2
3.2 FX-50DU-TK(S)-C Dimensions ....................3-3
3.3 Environment Specification .......................3-3
3.4 Data Access Unit Mounting ......................3-4
3.5 Control Devices ............................3-5
4.General Wiring
4.1 Wiring Cautions ............................4-2
4.2 Termination at screw terminals ....................4-2
4.3 Power Supply wiring ..........................4-2
4.4 Power Supply Wiring Cautions ....................4-2
4.5 Communication Cables ........................4-4
5. Diagnostics
5.1 Error Messages ............................5-2
5.2 Maintenance ..............................5-4
5.2.1 General Maintenance ......................5-4
5.2.2 Display and Back Light ......................5-4
5.2.3 Battery Replacement ......................5-4
5.2.4 Installing the EPROM ......................5-4
6. Index
Graphic FX-50DU-TK(S)-C Units
iv

1Introduction
2Terminal Layouts
3Installation Notes
4 Wiring
5Diagnostics
6Index
Graphic FX-50DU-TK(S)-C Units Introduction 1
1 – 1

1. Introduction
This manual covers the hardware specifications and installation instructions for the
following graphic data access units:
-FX-50DU-TK-C (monochrome)
-FX-50DU-TKS-C (STN; 8 colors)
1.1 The Complete Family Of Graphic Data Access Units
FX-25DU-E FX-30DU-E FX-40DU-TK-E
Graphic FX-50DU-TK(S)-C Units Introduction 1
1 – 2

1.2 Dimensions and Specifications
1.2.1 FX-50DU-TK(S)-C Dimensions
1.2.2 Unit Characteristics
MODEL SCREENTYPE KEYS IP RATING
FX-50DU-TK-C 320 ✕240 dots
40 ✕15 chars
96 ✕72 mm
TOUCH SCREEN
Monochrome LCD Complete Touch
Key operation
16 ✕8 zones
(32 per screen + 32
global)
IP 65
(Based on
manufacturer’s
own tests)
FX-50DU-TKS-C 8 color LCD
1.2.3 Basic Specifications
MODEL POWER SUPPLY DIMENSIONS (mm, inch) WEIGHT
WH D kg (lbs)
FX-50DU-TK-C 24V DC
+10%
-15%
220mA 170 (6.69) 130 (5.12) 66 (2.60) 1.0 (2.2)
(includes brackets:
0.1 (0.22))
FX-50DU-TKS-C 250mA
66 (2.60)
5.5
(0.22)
120
(4.72)
about 110 (4.33)
130
(5.12)
160 (6.30)
170 (6.69)
Graphic FX-50DU-TK(S)-C Units Introduction 1
1 – 3