Mobatime ECO-M-DSC Series User manual

© MOBATIME BE-801314.00
INSTRUCTION MANUAL
In- and Outdoor Digital Clock
ECO-M-DSC Series

© MOBATIME 2 / 52 801314.00
Certification of the Producer
STANDARDS
The digital clock DSC has been developed and produced in accordance with the EU Standards
2006/95/ES (LVD), 2004/108/ES (EMC), 2011/65/EU (RoHS), 2002/96/EC (WEEE):
Applied Standards:
EN 60950-1/Cor. (2011)
EN 55022 (2010), class B
EN 55024 (2010)
EN 50121-4/Cor. (2008)
References to the Instruction Manual
1. The information in this Instruction Manual can be changed at any time without notice.
The current version is available for download on www.mobatime.com.
2. This Instruction Manual has been composed with the utmost care, in order to explain all details in
respect of the operation of the product. Should you, nevertheless, have questions or discover errors
on this manual, please contact us.
3. We do not answer for direct or indirect damages, which could occur, when using this Manual.
4. Please read the instructions carefully and only start setting-up the product, after you have correctly
understood all the information for the installation and operation.
5. The installation must only be carried out by skilled staff.
6. It is prohibited to reproduce, to store in a computer system or to transfer this publication in a way
or another, even part of it. The copyright remains with all the rights with BÜRK MOBATIME GmbH,
D-78026 VS-Schwenningen and MOSER-BAER AG – CH 3454 Sumiswald / SWITZERLAND.

© MOBATIME 3 / 52 801314.00
Table of contents
1Description ..................................................................................................................................................... 5
1.1 Basic properties........................................................................................................................................5
2Installation ...................................................................................................................................................... 7
2.1 Single-sided clock ....................................................................................................................................7
2.2 Assembly diagram....................................................................................................................................8
2.3 Double-sided ............................................................................................................................................8
2.4 Assembly diagram....................................................................................................................................9
2.5 Mechanical drawing ...............................................................................................................................10
2.5.1 Single-sided clock with wall mounting ............................................................................................10
2.5.2 Single-sided clock with ceiling suspension mounting.....................................................................10
2.5.3 Double-sided clock with ceiling suspension mounting ...................................................................10
2.6 Connectors and control elements ..........................................................................................................11
2.7 Function of the plug connectors .............................................................................................................12
2.8 Setting elements.....................................................................................................................................12
2.9 Connection of the cable ends.................................................................................................................13
3Control of the clock using keyboard or pushbuttons..............................................................................14
3.1 Setting of time and date .........................................................................................................................14
3.2 Menu for the setting of the clock parameters.........................................................................................14
3.2.1 Submenu for user-specific setting of time constants for data switchover ......................................15
3.2.2 Offset setting for time synchronization ...........................................................................................15
3.2.3 Submenu for network services configuration .................................................................................16
3.2.4 Manual setting of the IP address of the clock.................................................................................16
3.2.5 Manual setting of the subnet mask.................................................................................................16
3.2.6 Manual setting of default gateway IP address ...............................................................................17
3.2.7 Submenu for setting the multicast group address ..........................................................................17
3.2.8 Submenu for the setting of the NTP unicast synchronization ........................................................17
3.2.9 Submenu for displaying IPv6 addresses ........................................................................................18
4Control of the clock using IR remote control............................................................................................19
4.1 Setting of time and date .........................................................................................................................19
4.2 Menu for the setting of the clock parameters.........................................................................................20
4.2.1 Submenu for user-specific setting of time constants for data switchover ......................................21
4.2.2 Offset setting for time synchronization ...........................................................................................21
4.2.3 Submenu for network services configuration .................................................................................21
4.2.4 Manual setting of the IP address of the clock.................................................................................22
4.2.5 Manual setting of the subnet mask.................................................................................................22
4.2.6 Manual setting of default gateway IP address ...............................................................................22
4.2.7 Submenu for setting the multicast group address ..........................................................................22
4.2.8 Submenu for the setting of the NTP unicast synchronization ........................................................23
4.2.9 Submenu for displaying IPv6 addresses ........................................................................................23
5The clock menu table ..................................................................................................................................24
5.1 IPv6 adress submenu ............................................................................................................................26
6Control of the stopwatch via keyboard .....................................................................................................27
6.1 The stopwatch menu..............................................................................................................................27
6.2 Setting of the initial time for counting down ...........................................................................................27
7Control of the stopwatch using IR remote control ...................................................................................28
7.1 The stopwatch menu..............................................................................................................................28
7.2 Setting of initial time for counting down..................................................................................................29

© MOBATIME 4 / 52 801314.00
7.3 Switching contact ...................................................................................................................................29
8Stopwatch menu table.................................................................................................................................30
9Local time calculation .................................................................................................................................32
9.1 Basic setting – control according to source of synchronization .............................................................32
9.2 Calculation using MOBALine time zones ...............................................................................................32
9.3 Calculation using Timezone-server MOBATIME ...................................................................................32
9.4 Calculation using timezone entries preconfigured by MOBA-NMS software.........................................32
9.5 Calculation according to internal time zone table ..................................................................................33
10 Non-network clock operation ..................................................................................................................... 34
10.1 Autonomous clock synchronized by DCF 77 receiver ...........................................................................34
10.2 Autonomous clock synchronized by GPS4500 receiver ........................................................................34
10.3 Autonomous clock synchronized by internal GPS receiver ...................................................................34
10.4 Slave clock controlled by synchronizing impulses .................................................................................35
10.4.1 Synchronization and time setting – P5 mode 1 and 3....................................................................35
10.4.2 Synchronization only – P5 mode 2 and 4.......................................................................................35
10.5 Slave clock controlled by MOBATIME serial code, MOBALine, Active DCF code or IRIG-B................36
10.6 Cascaded connection of the DCF/GPS synchronised clock..................................................................36
11 NTP clock operation ....................................................................................................................................37
11.1 Unicast mode .........................................................................................................................................37
11.1.1 Network parameters assignation by DHCP....................................................................................38
11.1.2 Manual setting through setup menu ...............................................................................................38
11.1.3 Manual setting through telnet .........................................................................................................38
11.1.4 Setting network parameters over DHCPv6 ....................................................................................39
11.1.5 Setting network parameters over autoconfiguration (SLAAC) .......................................................39
11.1.6 SNMP .............................................................................................................................................40
11.2 Multicast mode .......................................................................................................................................40
12 Testing mode, parameter reset...................................................................................................................41
12.1 Synchronisation test...............................................................................................................................41
12.2 Parameter reset......................................................................................................................................41
13 Update firmware ........................................................................................................................................... 42
13.1 Update firmware trough TTL UART by protocol YMODEM 1K..............................................................42
13.2 Update firmware over Ethernet at NTP version .....................................................................................44
14 Time zone table ............................................................................................................................................45
15 Engineering data..........................................................................................................................................47
15.1 Standard design of the clock..................................................................................................................47
15.2 Voltage range and electric current consumption of the lines .................................................................48
16 Accessories ..................................................................................................................................................49
16.1 Single sided clock...................................................................................................................................49
16.2 Double sided clock .................................................................................................................................49
16.3 Optional accessories ..............................................................................................................................49
17 Cleaning ........................................................................................................................................................50
18 Disposal of used batteries ..........................................................................................................................50
19 Guarantee and maintenance.......................................................................................................................50

© MOBATIME 5 / 52 801314.00
1 Description
Digital clock of contemporary design and slim appearance. General-purpose digital clock,
intended particularly to be used outdoors. The clock meets the requirements of the majority of
conventional applications. 7segment display of high luminance LED for excellent readability for up
to 130 m distance from various angles of view even on direct sunshine. Autonomous TCXO time
base, with the possibility of synchronisation using DCF 77, Active DCF or MOBALine; IRIG-B,
GPS, NTP (PoE or mains powered) as option. NTP multicast or unicast synchronization in
Ethernet network. Mains powered, DC powering on request
1.1 Basic properties
•digit height of 100, 180, 250, 320 mm, which corresponds to readability distance
of 40, 70, 100, 130 m;
•digits in red colour;
•manual or automatic adjustment of the luminosity of LED displays;
•front side glass with dark filter and antiglare surface for improved readability;
•single sided design for wall mounting, single and double sided design for ceiling
suspension mounting;
•clock housing made of powder coated metal sheets, RAL9005 colour (black)
as standard, any other RAL colour on request;
•adjustment of clock parameters using two pushbuttons inside the clock (behind
the cover) or through remote controller;
•autonomous TCXO time base, with the possibility of synchronization using
DCF 77, Aktive DCF MOBAline; IRIG-B, GPS, NTP (PoE or mains powered)
as option;
•NTP multicast or unicast synchronization in Ethernet network
•mains powered, DC powering on request
•IPv4 and IPv6 support
•configuration / monitoring via MOBA-NMS is possible;
•protection degree IP 65
The clock
•display of time values (either 12 or 24 hours time cycle),
four digits (HH:MM) or six digits (HH:MM:SS) format
•display of calendar date in four or six digits format,
(DD.MM or DD.MM.YY)
•possibility of leading zero suppression when displaying the time and date;
•display of temperature in °C or °F – up to two sensors connectable;
•alternating indication of time, date and temperature, with adjustable period of
each of the displayed data;
•possibility of setting up the time zone.
•Temperature compensated RTC backup by means of lithium battery

© MOBATIME 6 / 52 801314.00
Stop watch
•counting up, starting from zero, up to 99 hours;
•countdown from a set up value, with stop at zero, automatic restart or counting to
negative values;
•indication of intermediate times, “freezing“ of the display, cumulated interim time;
•counting in steps of one minute, one second or 1/100 second;
•control using the keyboard or IR remote control;
•concurrently, possibility of changeover into the time/date display mode, or the
temperature indication
Accessories
•DCF 77/GPS receiver
•magnetic GPS antenna
•remote IR controller
On request
•housing colour

© MOBATIME 7 / 52 801314.00
2 Installation
The connection to the 110/230 V AC power network can only be done by authorized personnel
with appropriate qualification and training.
Connect the cables always in unpowered state – otherwise the risk of electric shock exist.
Producer is not responsible for breakdowns caused by unsuitable clock mounting on the
bearing surface.
2.1 Single-sided clock
•Prepare 2 holes in the wall by hinges pitch on the backside of clock.
•Insert the dowels to the prepared holes and screw the appropriate screws into
them.
•Remove the screws on the bottom of the clock. Remove the bottom cover and
front glass.
•Loosen the screws and remove the chassis with electronics; on ECO-M-DSC.100
disconnect DC power cable from clock electronics PCB (except PoE/PoE+); on
ECO-M-DSC.180 and higher disconnect DC power cable and flat data cable from
most left digit
•Remove the small cover, which includes gap with sealings for passage of cables
into the clock.
•Put the cable(s) through the opening and hang the clock on the prepared screws
in the wall.
•Tight the securing screws which prevent unauthorized demounting of the clock.
•Cut all cables to appropriate length and fix them with the holder in correct
positions in order to maintain regular spacing between the cables in the area of
passing through sealing; use appropriate force to not to damage the cables
insulation.
•Mount back the small cover and tight it’s screws with appropriate force.
•Connect the power cable to appropriate power supply terminals (except
PoE/PoE+ variant).
•Configure the Line type jumper according to used synchronisation signal (applies
only for DCF, MOBALine, Serial MOBATIME code, polarized impulse line or
IRIG-B).
•Connect the synchronisation / temperature / GPS cable to corresponding
terminals on the clock electronics PCB and/or crimp the RJ45 jack to the
Ethernet cable respectively.
•on ECO-M-DSC.100 connect the DC power cable back to electronics PCB
(except PoE/PoE+); on ECO-M-DSC.180 and higher connect DC power cable
and flat data cable back to most left digit; mount back the chassis with
electronics, tight the fixing screws.
•Mount back the front glass and bottom cover.

© MOBATIME 8 / 52 801314.00
2.2 Assembly diagram
2.3 Double-sided
•Prepare 4 holes for each suspension in appropriate pitch on the ceiling and insert
the dowels.
•Put the cables through one of the suspension tube and mount the suspension to
the ceiling.
•Remove the screws on the bottom of the clock, on the cover with triangle sign,
which identifies the side with access to clock electronics. Remove the cover and
front glass.
•Loosen the screws and remove the chassis with electronics; on ECO-M-DSC.100
disconnect DC power cable and flat data cable for second side from clock
electronics PCB (except PoE/PoE+); on ECO-M-DSC.180 and higher disconnect
DC power cable and flat data cable from most left digit.
•Put the cable(s) through the opening on top side and hang the clock on the
prepared ceiling suspension.
•Cut all cables to appropriate length.
•Connect the power cable to appropriate power supply terminals (except
PoE/PoE+ variant).
•Configure the Line type jumper according to used synchronisation signal (applies
only for DCF, MOBALine, Serial MOBATIME code, polarized impulse line or
IRIG-B).
•Connect the synchronisation / temperature / GPS cable to corresponding
terminals on the clock electronics PCB and/or crimp the RJ45 jack to the
Ethernet cable respectively.

© MOBATIME 9 / 52 801314.00
•On ECO-M-DSC.100 connect the DC power cable and flat data cable for second
side back to electronics PCB (except PoE/PoE+); on ECO-M-DSC.180 and
higher connect DC power cable and flat data cable back to most left digit; mount
back the chassis with electronics, tight the fixing screws.
•Mount back the front glass and bottom cover.
2.4 Assembly diagram

© MOBATIME 10 / 52 801314.00
2.5 Mechanical drawing
2.5.1 Single-sided clock with wall mounting
2.5.2 Single-sided clock with ceiling suspension mounting
2.5.3 Double-sided clock with ceiling suspension mounting

© MOBATIME 11 / 52 801314.00
2.6 Connectors and control elements
Note: The placement of particular connectors and control elements is different for the ECO-M-
DSC.100 clocks.

LINES, DC/DCF OUT – JP1
TEMP – JP2
CTRL – JP3
RS232 – JP4 (not available)
RS485 – JP5 (not available)
100 – 240VAC – JP6
LAN - JP7 (version NTP)
PROG – JP8
RELAY – JP27 (optional)

Line type jumper – JP11
PB1, PB2 buttons
RESET button
TRE jumper – JP10 (not available)
BATT jumper – JP12
jumper ISPE – JP9
LED indication of DCF signal
state LED
LED indication of powering
jumper DC Out / DCF Out – JP17

© MOBATIME 12 / 52 801314.00
2.7 Function of the plug connectors
LINES, DC/DCF OUT – JP1 time signal inputs: The DCF/GPS receiver,
polarized impulse line, MOBALine, MOBATIME
serial code, IRIG-B,
power supply output: DC OUT 12–40 VDC
or passive DCF current loop output
TEMP – JP2 connection of the temperature sensor(s)
CTRL – JP3 connection of the keyboard
100 – 240VAC – JP6 powering 100 - 240 VAC voltage
LAN - JP7 (optional) RJ45 10BaseT/100TX (IEEE 802.3)
auto negotiation
PROG – JP8 clock firmware programming
RELAY – JP27(optional) switching contact connection
2.8 Setting elements
Line type jumper – JP11 for the setting of the slave line type
IRIG / AFNOR
DCF
MOBALine
(Un)polarized impulse line
MOBATIME serial code
Active DCF code
PB1, PB2control pushbuttons
RESET the RESET button
BATT jumper – JP12 backup battery connection
ISPE jumper – JP9 invoking the firmware programming mode
DCF LED indication of receiving the DCF signal
STATE LED state indication
POWER LED power indication
jumper DC Out / DCF Out – JP17 Output signal setting on pins 3, 4
of the JP1 connector
pin3 = DC Out + (12-40V)
DC Out
pin4 = DC Out -
pin3 = (+)
passive DCF Out
pin4 = (-)

© MOBATIME 13 / 52 801314.00
2.9 Connection of the cable ends
TEMP wire connection – 1 or 2 thermometers
CTRL wire connection

© MOBATIME 14 / 52 801314.00
3 Control of the clock using keyboard or pushbuttons
The clock is adjusted and controlled using two pushbuttons located on the control PCB. If you
use a keyboard for setting the stopwatch, then use the pushbuttons PB1 and PB2 for the
clock setting.
Abbreviations used for the key strokes
PB1L, PB2L pushing the pushbutton for more than 1 second
PB1S, PB2S pushing the pushbutton for less than 1 second
Function of the pushbuttons in the “Clock“ mode
PB1S time correction to the whole minute (±30 sec)
PB2S changeover of the displayed items
Time -> date -> temperature -> stopwatch -> time
PB1L entry into the time and date setting mode
PB2L entry into the clock menu
3.1 Setting of time and date
The setting of time and calendar date takes place in following steps: year – days
– months – hours – minutes. The entry into the time and date setting
mode occurs by pushing the PB1L pushbutton.
The display shows the following:
The item to be adjusted
is now blinking.
Move to another item by pushing the PB1S pushbutton. After having adjusted the
minutes and by pushing PB1S,the entered values are stored (the seconds are
set to zero) and the operation of the clock resumes. The clock returns into normal
working mode.
Function of the pushbuttons in the “Time and date setting“ mode.
PB1S advancement to another item to be set up
PB2S increase of the item to be set up by 1
PB2L continuous increase of the current item
3.2 Menu for the setting of the clock parameters
The entry into the parameter setup menu is done by pushing the
PB2L button.

© MOBATIME 15 / 52 801314.00
The display shows the following:
The item to be adjusted
is now blinking
The options for the parameter setup are shown in the clock menu table
(chapter 5).
Function of the pushbuttons in the setup menu mode
PB1S storage of the current item and move to another menu item
PB1L storage of values and return into normal display mode, or entry
into the submenu, where it is permitted by the program
PB2S increase of the current item by 1
PB2L continuous increase of the current item
PB1L+PB2L return into normal display mode, without storage of the data
3.2.1 Submenu for user-specific setting of time constants for data switchover
In menu item P2 (time constants for automatic switching over of values) set value
U, then by pushing the PB1L enter the submenu. The item to be set is blinking.
By pushing the PB2S button the adjusted value is increased in steps of 1, by
pushing the PB2L button the value will be continuously increased.
The display shows the following:
Enter the time constant for the display of
time in seconds. Push the PB1S button
and enter the constant for date display
in seconds.
Push the PB1S pushbutton.
The display shows the following:
Enter the time constant for the display
of temperature in seconds. Push the
PB1S pushbutton and enter the
constant for stopwatch display in
seconds.
By pushing the PB1L button are the entered values stored and the clock returns
to the menu item P2.
3.2.2 Offset setting for time synchronization
Clocks can run with a defined offset to synchronization source.
In menu item P4 (synchronization source), push PB1L to go to the time
synchronization offset setting submenu.
The setting unit is 1/100 second.
Setting range -9.99 to +9.99.
Push PB1Lto save the setting and return to menu item P4.
Push together PB1L and PB2L to return to P4 without storage of the data

© MOBATIME 16 / 52 801314.00
3.2.3 Submenu for network services configuration
Choose the value 2or 3in the item P19 (network workmode selection) in the
clock menu, then enter the submenu by pushing the PB1L pushbutton for
configuring the network services (Multicast support in unicast workmode, SNMP
service, Telnet service). The item to be set is blinking.
The display shows the following:
Set value 1for enabling the multicast
support in the unicast workmode or
value 0for disabling it by pushing the
PB2S.
Switch to the next parameter – SNMP communication support by pushing the
PB1S. The display shows the Sn: 1. Set value 1for enabling the SNMP support
or value 0for disabling it by pushing the PB2S.
Switch to the next parameter – Telnet support by pushing the PB1S. The display
shows the tn: 1. Set value 1for enabling the telnet support or value 0for
disabling it by pushing the PB2S.
By pushing PB1L save the setting and return to item P19.
3.2.4 Manual setting of the IP address of the clock
Choose the item P20 in the main menu and push the PB1Lbutton to enter the
submenu for setting the IP address. The item to be set is blinking.
By pushing PB2S,the adjusted digit value is increased in steps of 1, by pushing
the PB2L button, the value will be continuously increased.
The display shows the following:
Enter the four octets of the IP address
step by step. Switch to next digit or octet
respectively by pushing the PB1S.
Octets are marked by letters A, b, C
and d.
By pushing the PB1Lbutton, the entered values are stored and the clock returns
to the menu item P20.
3.2.5 Manual setting of the subnet mask
Choose the item P21 in the main menu and push the PB1L button to enter the
submenu for setting the subnet mask. The item to be set is blinking.
By pushing PB2S,the adjusted value is increased in steps of 1, by pushing the
PB2L button, the value will be continuously increased.
The display shows the following:
Enter the four octets of the subnet mask
step by step. Switch to the next octet by
pushing the PB1S button. Octets are
marked by letters A, b, Cand d.
By pushing the PB1Lbutton, the entered values are stored and the clock returns
to the menu item P21.

© MOBATIME 17 / 52 801314.00
3.2.6 Manual setting of default gateway IP address
Choose item P22 in the main menu and push the PB1Lbutton to enter the
submenu for setting the default gateway IP address. The item to be set is
blinking.
By pushing PB2S the adjusted digit value is increased in steps of 1, by pushing
the PB2L button the value will be continuously increased.
The display shows the following:
Enter the four octets of the gateway IP
address step by step. Switch to the next
digit or octet respectively by pushing the
PB1S button. Octets are marked by
letters A, b, Cand d.
By pushing PB1L button are the entered values stored and the clock returns to
the menu item P22.
3.2.7 Submenu for setting the multicast group address
Choose the menu item P23 and then enter the submenu by pushing the PB1L
pushbutton for setting the multicast group address. The item to be set is blinking.
By pushing the PB2S button, the adjusted digit value is increased in steps of 1;
by pushing the PB2L button, a continuous increase of the value takes place.
The display shows the following:
Enter the four octets of the IP address step by
step. Switch to the next digit or octet respectively
by pushing the PB1S button. Octets are marked
by the letters A, b, Cand d.
By pushing the PB1L button, the entered values are stored and the clock returns
to the menu item P23.
3.2.8 Submenu for the setting of the NTP unicast synchronization
Choose the menu item P24 then enter the submenu by pushing the PB1L
pushbutton for setting the parameters of the NTP unicast synchronization. The
item to be set is blinking.
By pushing the PB2S button, the adjusted digit value is increased in steps of 1;
by pushing the PB2L button, the value will be continuously increased.
The display shows the following:
Set the four octets of the NTP server’s IP address
step by step. Switch to the next digit or octet
respectively by pushing the PB1S button. Octets
are marked by letters A, b, Cand d.
After the last octet setting, set the constant xwhich determines the interval of
synchronization in seconds.
By pushing the PB1L button, the entered values are stored and the clock returns
to the menu item P24.

© MOBATIME 18 / 52 801314.00
Note: Through the setup menu is possible to set only one NTP server IP address.
If more than one NTP server addresses were previously configured (using telnet
or MOBA-NMS tool), after opening the P24 submenu the IP address of currently
active NTP server is displayed. When the IP address was modified and the
configuration is saved using the setup menu, the IP address is stored to the
definition of the first NTP server, the other NTP server addresses are cleared
including those defined by the NTP server domain names.
3.2.9 Submenu for displaying IPv6 addresses
Choose the menu item P25 and push PB1L to enter the IPv6 addresses
submenu. In the submenu choose required IP address for displaying and push
PB1L to display the first part of the IPv6 address.
The IPv6 address consists of a total of 8 parts. You can switch to IPv6 address
particular part by pushing PB1S. The parts are distinguished by the decimal dots
on the last three digits. Decimal dots show the order of each IPv6 address parts
(0-7) in the binary system.
Push together PB1L and PB2L to return to P25.
Example of IPv6 address display 2001: 0db8: 0000: 0012: f68e: 38ff: fee8: 4a13
2001 – first part of IPv6 address (000b)
0db8. – second part of IPv6 address (001b)
000.0 – third part IPv6 address (010b)
001.2. – fourth part of the IPv6 address (011b)
f6.8e – fifth part of the IPv6 address (100b)
38.ff. – sixth part of the IPv6 address (101b)
fe.e.8 – seventh IPv6 address (110b)
4a.1.3. – eighth part of iPv6 address (111b)

© MOBATIME 19 / 52 801314.00
4 Control of the clock using IR remote control
A 2-digit address is assigned to the clock. With the IR remote control the clock can be locked.
The setting of time, date and the clock parameters can only take place at clocks in an
unlocked state.
Function of the pushbuttons in normal display mode
pushing F1 + entry of 2-digit address, unlock the clock with the
using numerical pushbuttons corresponding address
holding down F1 button unlock all clocks within the reach of the IR
beam of the remote control unit
holding down F2 button lock all clocks within the reach of the IR
beam of the remote control unit
holding down F3 button display the address of all locked clocks within
the reach of the IR beam of the remote control
Function of the pushbuttons in the “Clock“ operation mode
SET entry into the time and date setting mode
The + button button brightness increase (not applicable when
P0 is set to A)
The - button button brightness decrease (not applicable when
P0 is set to A)
CLOCK visualisation of time
DATE visualisation of date
TEMP visualisation of temperature
TIMER visualisation of stopwatch
MENU entry into the menu of setting of clock
parameters
CLR time correction to the whole minute (±30 sec)
4.1 Setting of time and date
The time and date values are adjusted in the following sequence: year – day –
month – hours – minutes. By pushing the SET button enter the time and date
setting mode.
The display shows the following:
The item to be set is blinking.
After having set up the minutes the value is blinking. By pushing the OK button
the value is stored (with seconds reset to zero) and the clock operation resumes.
The clock returns into normal working mode.
Function of the pushbuttons in the “Time and date setting“ mode
The +pushbutton increase of the value adjusted, in steps of 1
The –pushbutton decrease of the value adjusted, in steps of 1
Holding down the +button continuous increase of the value set up

© MOBATIME 20 / 52 801314.00
Holding down the –button continuous decrease of the value set up
ESC return into normal display mode, without storage
of the data
>> move to next parameter
<< move to previous parameter
CLR entry of zero or minimum value
OK storage of values set up and return into normal
working mode, followed with seconds reset
Pushbuttons 0–9 entry of the corresponding numerical value
4.2 Menu for the setting of the clock parameters
The entry into the menu for the setting of the clock parameters is done be
pushing the MENU button.
The display shows the following:
The item to be set is blinking.
The options for the parameters to be set up are shown in the menu table on page
(chapter 5).
Function of the pushbuttons in the “MENU“ mode
>> move to next menu item
<< move to previous menu item
The + button increase of the value adjusted,
in steps of 1
The - button decrease of the current value,
in steps of 1
Holding down the +button continuous increase of the value set up
Holding down the –button continuous decrease of the value set up
ESC return into the normal working mode,
without storing the modified items
OK storing of the modified items and return
into the normal working mode
SET enter the sub-menu, where it is possible
Pushbuttons 0–9 entry of the corresponding numerical value
Note: During entering the numbers in the octets
of the IP addresses the editing to the next digit
moves automatically.