Mocka Aspen Cot User manual

mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
Aspen
Cot
Thank you for your purchase.
Please follow the manufacturers assembly instructions in detail
to ensure the safety features of the cot are not compromised.
Hardware Supplied
A
8x
B
bolt
16x
C
bolt
8x
D
bolt
8x
E
nut
8x
F
dowel
1x
allen key
WARNING:
TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT
SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE
THE CHILD CAN SIT UP.
Ensure the cot is placed at a reasonable distance from curtains, blinds, heaters and power
points. Keep all medications, string, elastic, small toys or small items, such as money, out
of reach from any position in the cot.
Assembly
Care must be taken when attaching sides. Do not over-tighten screws as this can cause
damage to the cot.
Care and Maintenance
Regularly check all screws for tightness or damage that could render the cot unsafe. To
clean - use a damp cloth, avoiding the use of detergents or abrasives.
Recommended mattress size
This cot has been manufactured for use with a mattress which measures 1300mm long x
690mm wide x 100mm in thickness. The width and length are specified because it is impor-
tant that gaps between the mattress and the sides and ends of the cot will not exceed 40mm.
This is to minimize the risk of a child’s limb becoming caught in the gap. The thickness of the
mattress has been specified to ensure that the depth of the cot is greater than 500mm with
the mattress base in the lower position to minimize the risk of a child climbing or falling out
of the cot.
Flathead screwdriver required

Aspen
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
2
1
Cot
Insert 8x dowel (E) into 2x panel [7]. Attach 2x panel [5] and 2x panel
[6] to 2x panel [7] with 4x bolts (B). Tighten all bolts with allen key (F).
Place 8x nut (D) inside panels [5] and [6].Attach panels [5] and [6]
to panel [4] with 8x bolts (C). Use a flathead screwdriver to align
nuts (D) with bolts (C). Tighten all bolts with allen key (F).
B
B
B
B
E
E
E
E
E
E
E
E
C
C
C
C
C
F
D
D
D
F
B
6
6
6
6
5
5
5
5
7
7
4
2

Aspen
Cot
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
34
B
Attach 2x panel [1] to panel [4] with 4x bolts (B). Tighten all bolts with allen key (F). Attach 1x panel [2] to panels [1] with 4x bolts (A). Attach panel [2]
to panel [4] with 2x bolts (B). Tighten all bolts with allen key (F).
B
B
B
B
B
A
A
A
A
4
2
1
1
1
1
F
B
FB
A

mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
Aspen
Cot
56
Attach panel [3] to panels [1] with 4x bolts (B). Tighten all bolts with allen key (F). Attach 1x panel [2] to panels [1] with 4x bolts (A).Attach panel [2]
to panel [4] with 2x bolts (B). Tighten all bolts with allen key (F).
FB
A
B
B
B
B
A
A
A
A
B
B
4
3
2
1
1
1
1
F
B

Aspen
Cot
mocka.co.nz I mocka.com.au I PO BOX 18, Pinkenba QLD 4008
ASSEMBLY I N S TRUCTION S
78
B
B
B
B
5
OPTIONAL/MATTRESS HEIGHT ADJUSTMENT
(please keep these instructions handy for future reference)
All done! Regularly check all screws are suitably tightened. Place the
correct size mattress into the cot before use. To clean use a damp cloth,
avoiding the use of detergents or abrasives. Once assembled lift furniture
into place, do not drag.
To adjust mattress base settings, remove small plastic plugs. This will
require a small amount of force, please note these are not screws and
cannot be screwed out. You will need a screwdriver that fits into the centre
hole and possibly a hammer, or similar, to gently tap the end until the plug
pops out.
Repeat steps 2, 3 and 4 by removing the side panel and moving the base to
corresponding holes. Securely attach again in the adjusted position.