Mocka Jimmy Change Table User manual

nut
x20
A B C
D E F
Phillips & Flathead screwdrivers required
Hardware Supplied
dowel
x10
bolt
x16
bolt
x18
locking
nut x18
bolt
x4
*We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.
Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%.
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
WARNING: Any furniture that is not anchored to a wall has the potential to tip
over in certain circumstances, i.e. if a child attempts to climb up on the furniture
or in the event of an earthquake. Accordingly, we recommend that all furniture
is anchored to a wall. We supply a free safety wall anchor with all furniture sold
and we recommend these are used to prevent your product tipping. The fixing
device provided should fit most wall types, but please note that different wall
materials may require different fixing devices from those supplied.
x1
washer
Z
wall
screw x1
r/washer
screw
x1
Y
wall
anchor
x1
X
safety
strap x1
Wall Strap
W
Jimmy Change Table
1
mocka.co.nz | mocka.com.au
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.

12
Attach panels [2] and [3] to panel [1] using 4x bolts (A) and secure with
4x locking nuts (B). Tighten with a screwdriver.
A
A
A
A
BB
B
3
2
1
1
Attach the wall strap (W) to the preferred position on the underside of
panel [1] using 1x r/washer screw (Y). Tighten with a screwdriver.
Y
W
Jimmy Change Table
2
mocka.co.nz | mocka.com.au
Assembly Instructions

12
Attach panels [2] and [3] to panel [1] using 4x bolts (A) and secure with
4x locking nuts (B). Tighten with a screwdriver.
A
A
A
A
BB
B
3
2
1
1
Attach the wall strap (W) to the preferred position on the underside of
panel [1] using 1x r/washer screw (Y). Tighten with a screwdriver.
Y
W
34
Attach panels [6], [7] and 2x [8] together using 4x dowels (C), 4x bolts
(D) and secure with 4x nuts (E). Tighten with a screwdriver and repeat
to assemble the other legs.
D
C
D
C
C
D
C
EE
EE
D
8
76
8
x2
Attach panels [4] and [5] to panels [1], [2] and [3] using 2x dowels (C),
14x bolts (A) and secure with 14x locking nuts (B). Tighten with a
screwdriver.
C
AA
A
A
A
A
A
B
B
B
CA
A
B
BB
3
2
15
4
B
Jimmy Change Table
3
mocka.co.nz | mocka.com.au
Assembly Instructions

56
Attach panel [1] to the base as shown using 4x bolts (F) and secure
with 4x nuts (E). Tighten with a screwdriver.
EE
E
F
F
F
F
1
Attach the legs to panels [9] using 8x bolts (D) and secure with 8x nuts
(E). Tighten with a screwdriver.
D
D
D
D
D
D
D
D
E
E
E
E
E
E
9
9
Jimmy Change Table
Assembly Instructions
4
mocka.co.nz | mocka.com.au

Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
56
Attach panel [1] to the base as shown using 4x bolts (F) and secure
with 4x nuts (E). Tighten with a screwdriver.
EE
E
F
F
F
F
1
Attach the legs to panels [9] using 8x bolts (D) and secure with 8x nuts
(E). Tighten with a screwdriver.
D
D
D
D
D
D
D
D
E
E
E
E
E
E
9
9
78
Ensure the unit is balaced and steady before use. You’re done, enjoy!
Once assembled lift furniture into place, do not drag. Use a drill to create
a small hole lining up with the top of the safety strap (W). Fasten to wall
using 1x wall plug (X), 1x washer (Z) and 1x wall screw (not supplied).
Wall Strap
XZ
W
W
Z
X
Jimmy Change Table
Assembly Instructions
5
mocka.co.nz | mocka.com.au