Mocka Jesse Bedside Table User manual

B
A
x20
CD E
FG
x20
x8 x2
L + R
bolt
locking nut
dowel
HIJ
35 mm
x8
small screw
x1
allen key
x4 x4
screw
x4
Hardware Supplied
*We recommend using a Flathead screwdriver to tighten all locking nuts 100%
inserting the nut to ensure it locks 100%
WARNING: Any furniture that is not anchored to a
wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on
the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is
anchored to a wall. We supply a free safety wall
anchor with all furniture sold and we recommend
these are used to prevent your product tipping. The
fixing device provided should fit most wall types, but
please note that different wall materials may require
different fixing devices from those supplied.
x2
L + R
x2
washer
Z
wall
screw
Y
wall
anchor
x1
X
safety
strap x1
W
V
screw
x1
x1
Wall Strap
cam nut cam bolt long
screw x4
Jesse Bedside Table
1
mocka.co.nz | mocka.com.au
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
For quicker assembly, we recommend the use of a power drill on a low-speed setting.
Phillips & Flathead screwdriver required

12
To begin assembly, screw 4x bolts (A) and insert 4x wooden dowels
(B) into panel [1].
Next attach 2x rail components (D) to the inside of panels [3] & [4] using
2x screws (C) in each and the holes provided.
AB
BA
AB
BA
A
x4
1
4
C
C
D
3
C
C
D
x4
C
Jesse Bedside Table
2
mocka.co.nz | mocka.com.au
Assembly Instructions

12
To begin assembly, screw 4x bolts (A) and insert 4x wooden dowels
(B) into panel [1].
Next attach 2x rail components (D) to the inside of panels [3] & [4] using
2x screws (C) in each and the holes provided.
AB
BA
AB
BA
A
x4
1
4
C
C
D
3
C
C
D
x4
C
34
Slot panels [3] and [4] together with panel [1]. Place 4x locking nuts (E)
into holes in the vertical panels and tighten with a flathead screwdriver.
Slide the back panel [5] down into place in the grooves of panel [3] and
[4].
Insert 4x dowels (B) into the top of panel [3] and [4]. Attach the base
panel [2] by inserting 4x long screws (H) and tighten with a screwdriver.
Screw 8x bolts (A) into holes in the base panel [2].
E
x4
4
E
3
E
E
1
5
B
A
x8
H
x4
H
A
A
A A A
A
A
H
H
H
B
B
B
2
4
3
A
Jesse Bedside Table
3
mocka.co.nz | mocka.com.au
Assembly Instructions

56
To assemble the base insert 4x bolts (A) and screw 4x cam bolts (G)
into pieces [6] & [7] using the allen key (J). Insert 2x cam nuts (F) into
each support panel [9]. Connect all components together using 4x
locking nuts (E). Tighten with a screwdriver.
Attach the base and legs using 8x locking nuts (E). Tighten with a
screwdriver.
E
x4
A
A
x4
6 7
9
9
E
8
6
7
8
7
6
E
G
G
G
F
G
EFF
EF
E
EE
G
J
E
Jesse Bedside Table
Assembly Instructions
4
mocka.co.nz | mocka.com.au

Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
56
To assemble the base insert 4x bolts (A) and screw 4x cam bolts (G)
into pieces [6] & [7] using the allen key (J). Insert 2x cam nuts (F) into
each support panel [9]. Connect all components together using 4x
locking nuts (E). Tighten with a screwdriver.
Attach the base and legs using 8x locking nuts (E). Tighten with a
screwdriver.
E
x4
A
A
x4
6 7
9
9
E
8
6
7
8
7
6
E
G
G
G
F
G
EFF
EF
E
EE
G
J
E
78
To assemble the drawer screw 4x bolt (A) into holes in the front panel
[10]. Attach side panels [11] and [12] to the front panel by inserting 4x
locking nuts (E) into holes in the side panels and tighten with a flathead
screwdriver.
Slide the base panel [13] into place in the grooves in side and front
panels as shown.
Drawer
A
x4
E
x4
13
11
12
10
E
E
AA
E
AA
10
Drawer
Jesse Bedside Table
Assembly Instructions
5
mocka.co.nz | mocka.com.au

910
Attach the back panel [14] into place between the side panels [11] and
[12] using 4x screws (I) in the holes provided with a screwdriver.
Attach 2x rail components (D) to both left and right side of each drawer
using 4x screws (C).
x4
I
II
I
I
14
12
11
DL
C
C
C
C
DR
DrawerDrawer
Jesse Bedside Table
Assembly Instructions
6
mocka.co.nz | mocka.com.au

910
Attach the back panel [14] into place between the side panels [11] and
[12] using 4x screws (I) in the holes provided with a screwdriver.
Attach 2x rail components (D) to both left and right side of each drawer
using 4x screws (C).
x4
I
II
I
I
14
12
11
DL
C
C
C
C
DR
DrawerDrawer
11
12
Flip the bedside cabinet over onto its legs. To complete the assembly
slide the completed drawer into place on the rails in the beside cabinet
as shown.
Ensure that the drawer easily slides open and closed.
Jesse Bedside Table
Assembly Instructions
7
mocka.co.nz | mocka.com.au

13 14
Attach 1x safety strap (V) to the top of the back side of the unit using 1x
washer (Z) abd 1x screw (W). Tighten with a screwdriver. Once
assembled lift furniture into place, do not drag.
Move the unit into the desired location up against a wall. Use a drill to
create a small hole lining up with the top of the safety strap (V). Fasten
to wall using 1x wall plug (X) and 1x long screw (Y). Ensure unit is
balanced and steady before use. You’re done, enjoy!
Wall Mount
V
W
Z
Z
V
W
X
Y
Z
wall
plug
screw
strap
washer
Jesse Bedside Table
Assembly Instructions
8
mocka.co.nz | mocka.com.au