modway EEI-3046 User manual

EEI-3046 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 6
Thank you for purchasing the
MODWAY SOFA.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the sofa, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A. Bolt M8x60mm x 20
B. Flat Washer M8x 20
C. Allen Wrench x1
Component:
1 Back Cushion x2 2 Left Back Frame x1 3 Right Back Frame x1 4 Left Arm x1
5 Right Arm x1 6 Seat Frame x1 7 Seat Cushion x2 8 Tilted Leg x4 9 Straight Center Leg x1
7

EEI-3046 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 6
STEP 1:
Please take the compressed Seat Cushions (7), Back Cushions (1), all Legs and hardwares bag from the
bottom of Seat Frame (6).
Carefully remove plastic packaging of the compressed Seat Cushions (7) and Back Cushions (1).
Being carefully not to cut through to them.
Place compressed Seat Cushions (7) and Back Cushions (1) on a flat surface in a well ventilated room and
allow 48 hours for expansion.
Due to the unique properties of the compressed Seat Cushions (7) and Back Cushions (1), dimensions after
expansion will vary slightly; this is normal and will not affect the performance of your sofa.
STEP 2:
Please put Seat Frame (6) on a carpeted or padded surface.
Attach 1 piece of Tilted Legs (8) to the one corner of Seat Frame (6) by using 2 pieces of Bolts (A)with 2 pieces
of Flat Washers (B)as shown. Repeat the same steps for the other 3 pieces of Leg (8).
Tighten Bolts (A)by using Allen Wrench (C) fully as shown.
Hardware & Tools required
8
8
8
8
A
x 8x 8
B
x 1
C
7
7
7
Carefully remove
plastic packaging
8
9
HARDWARE
INSIDE

EEI-3046 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 6
STEP 3:
Insert Straight Leg (9) to the middle of bottom of Seat Frame (6) and fully tighten by hand in the direction of
the arrow.
STEP 4:
Attach Left Arm (4) to the left side of Seat Frame (6) by using 4 pieces of Bolts (A) with 4 pieces of Flat
Washers (B) as shown.
Tighten Bolts (A) by using Allen Wrench (C) fully as shown.
Hardware & Tools required
8
8
8
8
9
A
C
B
8
8
8
8
A
x 4x 4
B
x 1
C

EEI-3046 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 6
STEP 5:
Attach Right Arm (5) to the right side of Seat Frame (6) by using 4 pieces of Bolts (A) with 4 pieces of Flat
Washers (B) as shown.
Tighten Bolts (A) by using Allen Wrench (C) fully as shown.
Hardware & Tools required
STEP 6:
Slide the left clip of Left Back Frame (2) to the clips of the inner side of Left Arm (4) by hand in the direction of
the arrow as shown.
A
x 4x 4
B
x 1
C
A
C
B
8
8
2
5
4
2
4
2

EEI-3046 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 5 of 6
STEP 7:
Slide the two clips of Right Back Frame (3) synchronously to the clip of the inner side of the Right Arm (5) and
the clip of the left side of the Left Back Frame (2) by two hands in the direction of the arrow as shown.
STEP 8:
Carefully turn over the assembled unit from step 7 as shown.
Insert 4 pieces of Bolts (A) with 4 pieces of Flat Washers (B) into the pre-drilled holes on the back of the bottom
of Seat Frame (6).
Use Allen Wrench (C)to tighten Bolts (A) clockwise until secure.
Hardware & Tools required
5
4
2
3
A
x 4x 4
B
x 1
C

EEI-3046 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 6 of 6
STEP 9:
Carefully turn over the assembled unit from step 8 as shown.
Put Back Cushion (1) and Seat Cushion (7) to the assembled sofa as shown.
Assembly is complete. Your Sofa is ready to be used now!
2
3
4
5

SOFA USER GUIDELINE
This product makes a long journey to reach you and the cushion is
compressed, please reshape the cushion to restore to its original
beauty before using, steps as follows:
1.Carefully remove the plastic packing
and put the cushion on a flat surface in
a well ventilated room and allow 48
hours for expansion.
2.Press the back cushions with both
hands from side edge.
3.Press the back cushions with both
hands from front side.
4.Restoring action is complete,you
can put it to the assembled sofa now.