Moldex 2380 User manual

www.moldex.com
Datasheet
FFP masks
Protection against Dust, Mist & Fumes
EU - 01 - 2010 / 01
FFP1 NR D
2380 non valved
2385 with Ventex®-valve
FFP2 NR D
2480 non valved
2485 with Ventex®-valve
FFP3 NR D
2505 with Ventex®-valve
CHARACTERISTICS
ActivForm®
Automatically fits to the face.
No manual adjustments by the user are necessary.
DuraMesh®
Masks have a strong and durable structure
Ventex®-valve
Starts to open even at low exhalation pressure and
significantly reduces moisture and heat inside the mask.
Nose seal
The flexible nose seal improves fit and provides
optimum wearing comfort.
Adjustable Strap
Makes it easier to take the mask on and off and
to adjust to different head/neck dimensions.
Clip
Easy on & off; mask can be worn around the neck
during breaks.
Dolomite clogging test
Masks have passed the Dolomite clogging test.
Better breathing resistance for longer.
100% PVC-FREE
All Moldex products and packaging are
completely free from PVC.
NR (non reusable) = Single use.
Comfortable and durable throughout the whole shift
D
CERTIFICATION
The Moldex New Generation FFP-masks meet the requirements of EN149:2001 +
A1:2009 and are CE-marked in accordance with the requirements of European Di-
rective 89/686/EEC. The BGIA Germany is responsible for both type examination
(Article 10) and monitoring of production (Article 11).
The products are manufactured in an ISO 9001:2000 certified plant.
MATERIALS
Filter Layer, Inner Shell, DuraMesh®:Polypropylene,
Ethylene-vinyl acetate (EVA)
Nose Seal, Clip: Polyethylene
Ventex®-valve: Natural Rubber
Head Strap: Polyester, Natural Rubber
WEIGHT
2380: 16 g 2385: 18 g 2480: 20 g 2485: 22 g 2505: 24 g
AREAS OF USE
(WEL = Workplace Exposure Limit)
New Generation
Level WEL Hazard type
Examples
FFP1 4 x FINE DUSTS, FUMES, WATER AND OIL BASED MISTS/
AEROSOLS
Against non-toxic dusts, e.g. Aluminium Oxide, Bauxite,
Borax, Brick Dust, Cellulose, Cement, Coal Dust, Gypsum,
Limestone, Plaster of Paris, Pollen, Portland Cement,
Sucrose, Sugar
FFP2 10 x FINE TOXIC DUSTS, FUMES, WATER AND OIL BASED
MISTS/AEROSOLS
As FFP1 but at higher concentrations, plus: Brake Dust,
Calcium Oxide, China Clay, Concrete Dust, Cotton Dust,
Granite, Hay, Lead Dust and Fume, Particulate Welding
Fumes (no heavy metal), Silica, Sodium Hydroxide, Wood
Dust (softwood), Zinc Oxide Fume
FFP3 20 x FINE TOXIC DUSTS, FUMES, WATER AND OIL BASED
MISTS/AEROSOLS
As FFP2 but at higher concentrations, plus: Ceramic Fibres,
Chromates, Chromium, Cobalt, Nickel, Micro Organisms,
radioactive and biochemical active Aerosols

www.moldex.com
TESTING ACCORDING TO EN 149:2001 + A1:2009
Total inward leakage
Ten test subjects perform a variety of exercises. During the exercises the amount
of test aerosol that penetrates the filter, face seal and valve are sampled. The
total inward leakage of 8 out of 10 test subjects shall not exceed the following
levels:
The filter penetration after loading the filter with 120 mg paraffin oil according
to DIN EN 149:2001 + A1:2009 shall not exceed the following levels:
Flammability
4 respirators are passed through a 800°C (+/- 50°C) flame with a speed of 6 cm/s.
After passing through the flame the respirator has to self-extinguish.
Breathing Resistance
Thebreathingresistance producedbythefilter oftherespiratoris testedatan airflowof
30 l/min and 95 l/min.
INSTRUCTIONS FOR USE
· The user has to be trained and instructed in wearing the mask.
· FFP Masks do not protect against gases and vapours.
· The oxygen concentration of the ambient atmosphere should be at 19,5 % Volume.
· These respirators may not be used if the concentration type, and properties of
contaminants in the ambient atmosphere are unknown or at dangerous levels.
· Respirators should be disposed if damaged, if the breathing resistance be-
comes high due to clogging, or at the end of a shift.
· Never tamper with, alter or modify the respirator.
1. Pull strap to form a
large loop.
2. Place respirator on chin and
pull loop over head tight to
the neck.
3. Pull upper strap and place on
back of head.
4. Adjust strap by pulling
loop on strap.
5. During breaks unclip strap.
6. Let mask hang around
your neck.
INSTRUCTIONS FOR FITTING
EU - 01 - 2010 / 02
Datasheet
FFP masks
Protection against Dust, Mist & Fumes
Category max. breathing resistance
30 l / min 95 l / min
FFP1 0,6 mbar 2,1 mbar
FFP2 0,7 mbar 2,4 mbar
FFP3 1,0 mbar 3,0 mbar
Category FFP1 FFP2 FFP3
max. total inward leakage 22 % 8 % 2 %
Category FFP1 FFP2 FFP3
max. Filter penetration 20 % 6 % 1 %
INFO
For help on selection and training please
contact us. We offer a wide range of training
packages and support material.
MOLDEX-METRIC AG & Co. KG
Tübinger Straße 50
72141 Walddorfhäslach
Germany
Tel.: [phone]
Fax: [phone]
[email protected]
www.moldex-europe.com