Moldex 9000 Series User manual

EASY TO WEAR
At less than 13 ounces, the 9000 Series respirator is
ultra-lightweight. Workers will appreciate the comfort and
longer wearability and employers will benefit from increased
user acceptance.
ON & OFF MADE EASY
A convenient ratchet fastening strap system and the
stand-away head harness make donning and doffing the
9000 mask quick and easy. The strap tabs are securely
molded directly to the flange for rugged use.
A FRAMELESS MASK WITH A VIEW
The 9000 has an extra-wide viewing lens, with an exclusive
over-molded flange design. This eliminates the traditional
clamping frame found on most other face pieces.
COMPLETELY METAL-FREE
The 9000 is completely metal-free, making it ideal for mines,
refineries and other work environments where metal may be
hazardous.
MAINTENANCE HAS NEVER BEEN EASIER
Advanced design eliminates unnecessary parts. Our
over-molded flange and harness tabs, plus integrated
exhalation assembly, make cleaning and maintaining the
9000 Series respirator a breeze.
FEATURES
• High-tech, streamlined design for exceptional worker
acceptance.
• Exclusive over-molded lens offers greater field of vision.
• Lighter weight for superior all-day comfort.
• Fewer parts means less cost and easy maintenance.
• Stand-away head harness for easy donning and doffing.
• Lens stays away from flat surface when laid down to
avoid scratching.
• Tear away lens protector included.
• Lens meets ANSI Z87+ for high impact requirements.
• 100% PVC-Free for a greener alternative.
9000SERIES
REUSABLE RESPIRATORS

9000-807 REV B 1/19
®
PART # / DESCRIPTION SIZE DISPLAY CASE
9001 Full Facepiece S 1 per Box 2 Boxes
9002 Full Facepiece M 1 per Box 2 Boxes
9003 Full Facepiece L 1 per Box 2 Boxes
9000SERIES
REUSABLE RESPIRATORS
MOLDEX-METRIC, INC.
10111 Jefferson Blvd.
Culver City, CA 90232
TEL: [phone] or
[phone]
FAX: [phone]
E-mail: [email protected]
www.moldex.com
CANADIAN CUSTOMER SERVICE
Tel: [phone], Ext. 550
Fax: [phone]
USE AGAINST:
1. Contaminants specified on NIOSH approval label, matrix, cartridges or filters and
in accordance with all limitations and applicable safety and health regulations,
including OSHA.
2. Contaminants with good warning properties, i.e., smell, taste or irritation.
DO NOT USE AGAINST:
1. Concentrations of contaminants which are unknown, or are immediately dangerous
to life or health.
2. Concentrations of contaminants which exceed the maximum use concentration or
10X the OSHA Permissible Exposure Limit, (PEL), when qualitatively fit tested, or 50X
the PEL when quantitatively fit tested, or according to applicable government
regulations.
3. Gases or vapors with poor warning properties or those which generate high heats of
reaction, or paint sprays containing isocyanates.
4. Sandblasting.
5. Oil-based mists with N filters.
RESTRICTIONS:
01. This respirator does not supply oxygen and must not be used in atmospheres
containing less than 19.5% oxygen.
02. Do not remain in contaminated area if any physical distress occurs, for example
breathing difficulty, dizziness or nausea.
03. Leave contaminated area and replace respirator and/or cartridge or filter if it is
damaged, distorted, a proper fit cannot be obtained, you taste, smell or become
irritated by contaminants, or breathing becomes difficult.
04. Do not alter, modify, or abuse this respirator.
05. Store respirator in sealed bag in a clean, dry, non-contaminated area.
06. Dispose of facepiece, and/or cartridges and disks/filters according to your
employer’s policy and applicable regulations.
07. N, R or P filters are required for particulates.
08. Where oil mists are present, either alone or in combination with solid particulates,
do not use the R or P filters for longer than one eight-hour work shift. Dispose no
later than eight hours after first use. Do not exceed 10x PEL or a total of 200 mg
loading per respirator, whichever is lower. It is the user’s responsibility to know the
PEL and concentration of the contaminant, the maximum work rate of the
employee, and any other work site-specific information to calculate the loading of
the filter. Where oil mists are present do not use N filters.
09. Dispose of all cartridges, N, R, P filters no later than thirty days after a) first use,
and/or b) removing from sealed bag.
10. Use cartridges, filters, and facepieces before the “use by” expiration date printed on
box or bag.
LIMITED WARRANTY IMPORTANT NOTICE TO PURCHASER
This limited warranty is made in lieu of the warranties of merchantability, fitness for
particular purposes and all other warranties, express or implied. There are no other
warranties which extend beyond the description on the face hereof. The physical
standards and specifications of Moldex will be met by products sold. Exclusive
Remedies: damages for the breach of this limited warranty are limited to the replace-
ment of such quantity of Moldex, products proved to be defectively manufactured.
Except as provided above, Moldex shall not be liable or responsible for any loss,
damage, or liability, direct, indirect, incidental, special, or consequential, arising out of
sale, use, or misuse, or the inability to use products by the user.
MOLDEX TECHNICAL ASSISTANCE
For more information call [phone] or [phone], ext. 512/550 or
E-mail: [email protected], [email protected] or visit www.moldex.com.
DISTRIBUTED BY:
IMPORTANT NOTICE TO USERS
You are responsible to understand and follow all warnings, restrictions and
other information contained in the instruction manual before you enter a
contaminated work area. Failure to do so may result in sickness or death.
WARNING TO USER
1. Follow all instructions and warnings on the use of this respirator and wear
during all times of exposure. Failure to do so will reduce respirator
effectiveness, wearer protection, and may result in sickness or death.
2. For proper use, ask your supervisor or call [phone] or
[phone], ext. 512/550.
3. The user must first be trained by the employer in proper respirator use, in
accordance with applicable safety and health standards, for the
contaminant and exposure level in the assigned work area. A written
Respiratory Training Program must be in place and followed by each user
before first use. It must meet all requirements of all applicable standards,
including OSHA 29 CFR 1910.134, and in Canada CSA Z 94.4, e.g.
training, fit testing, medical evaluation, and applicable OSHA substance
specific standards.
4. The vapors, gases, dusts, mists, fumes, and other contaminants which
can be dangerous to your health include those which you cannot see,
taste, or smell.
5. Check with your supervisor for the appropriate cartridges and/or filters for
the contaminants in your work area.
6. A qualitative or quantitative fit test must be performed before a respirator
is assigned. Refer to current OSHA 29 CFR 1910.134 (f).
7. This respirator facepiece, when combined with any nuisance level organic
vapor and/or acid gas/particulate filter disk, may not be used for organic
vapor or acid gas contaminants exceeding their respective OSHA
Permissible Exposure Limit (PEL) or other government Occupational
Exposure Limits (OEL), whichever is lower. Nuisance level refers to
concentrations not exceeding the PEL or OEL, whichever is lower.
I
S
O
9
0
0
1
:
2
0
1
5
R
E
G
I
S
T
E
R
E
D
®