Moldex 3000 NR Series User manual

www.moldex.com
Datasheet
FFP masks
Protection against Dust, Mist & Fumes
EU - 01 - 2010 / 01
CERTIFICATION
The Moldex Series 3000 FFP-masks meet the requirements of EN149:2001 +
A1:2009 and are CE-marked in accordance with the requirements of European Di-
rective 89/686/EEC. The BGIA Germany is responsible for both type examination
(Article 10) and monitoring of production (Article 11).
The products are manufactured in an ISO 9001:2000 certified plant.
MATERIALS
Filter Layer, Inner Shell, DuraMesh®: Polypropylene,
Ethylene-vinyl acetate (EVA)
Cusion Seal: TPE
Head Strap: Polyester, Natural Rubber
Ventex®-valve: Natural Rubber
WEIGHT
3505: 42 g
AREAS OF USE
(WEL = Workplace Exposure Limit)
Series 3000 NR (3505)
CHARACTERISTICS
ActivForm®
Automatically fits to the face.
No manual adjustments by the user are necessary.
DuraMesh®
Masks have a strong and durable structure.
Ventex®-valve
Starts to open even at low exhalation pressure and
significantly reduces moisture and heat inside the mask.
Low breathing resistance
Pleated filter technology reduces inhalation resistance by up
to 50% whilst maintaining filtration performance.
Full face seal
3D face seal – like a rubber half mask – improves fit
and provides optimum wearing comfort.
Adjustable Clip
Easy on & off; Adjustable strap for optimal fit and
wearer comfort.
100% PVC-FREE
All Moldex products and packaging are
completely free from PVC.
NR (non reusable) = Single use.
Comfortable and durable throughout the whole shift
FFP3 NR
3505 with Ventex®-valve
Level WEL Hazard type
Examples
FFP3 20 x FINE TOXIC DUSTS, FUMES, WATER AND OIL BASED
MISTS/AEROSOLS
As FFP2 but at higher concentrations, plus: Ceramic Fibres,
Chromates, Chromium, Cobalt, Nickel, Micro Organisms,
radioactive and biochemical active Aerosols

www.moldex.com
TESTING ACCORDING TO EN 149:2001 + A1:2009
Total inward leakage
Ten test subjects perform a variety of exercises. During the exercises the amount
of test aerosol that penetrates the filter, face seal and valve are sampled. The
total inward leakage of 8 out of 10 test subjects shall not exceed the following
levels:
The filter penetration after loading the filter with 120 mg paraffin oil according
to DIN EN 149:2001 + A1:2009 shall not exceed the following levels:
Flammability
4 respirators are passed through a 800°C (+/- 50°C) flame with a speed of 6 cm/s.
After passing through the flame the respirator has to self-extinguish.
Breathing Resistance
Thebreathingresistanceproducedbythefilteroftherespiratoristestedatanairflowof
30 l/min and 95 l/min.
INSTRUCTIONS FOR USE
· The user has to be trained and instructed in wearing the mask.
· FFP masks do not protect against gases and vapours.
· The oxygen concentration of the ambient atmosphere should be at 19,5 % Volume.
· These respirators may not be used if the concentration type, and properties of
contaminants in the ambient atmosphere are unknown or at dangerous levels.
· Respirators should be disposed if damaged, if the breathing resistance
becomes high due to clogging.
· Never tamper with, alter or modify the respirator.
INSTRUCTIONS FOR FITTING
EU - 01 - 2010 / 02
Datasheet
FFP masks
Protection against Dust, Mist & Fumes
Category max. breathing resistance
30 l / min 95 l / min
FFP3 1,0 mbar 3,0 mbar
1.
2. Fasten the two pieces buckles
at the back of the neck.
3. Place respirator on chin and
lift upper strap to place on
back of neck.
4. Ensure respirator fits secure
and comfortable. To fasten
respirator pull strap at either
side of the buckle.
5. Unbuckle to take off. During
work breaks open the buckles
and let the mask hang around
the neck.
Category FFP3
max. total inward leakage 2 %
Category FFP3
max. Filter penetration 1 %
INFO
For help on selection and training please
contact us. We offer a wide range of training
packages and support material.
MOLDEX-METRIC AG & Co. KG
Tübinger Straße 50
72141 Walddorfhäslach
Germany
Tel.: [phone]
Fax: [phone]
[email protected]
www.moldex-europe.com